Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY(for 1GR-FE) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052502 AUTOMATIC TRANSMISSION ASSEMBLY(for 1GR-FE) A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 1GR-FE)  INSTALLATION  


PROCEDURE

Hide 2.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C209685

Attach the splines of the input shaft and turbine runner.


b.
C209687

Attach the splines of the stator shaft and stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter back approximately 10 mm (0.393 in.) and engage the splines while rotating the torque converter assembly.



c.
C217017

Turn the torque converter to engage the key of the oil pump drive gear with the slot on the torque converter assembly.


d.
C193529C01
2.76,1.438 2.479,1.708 2.479,1.708 2.479,1.875 false 2.438,0.708 2.438,1.042 false 1.302,0.563 1.156,0.563 1.156,0.563 1.021,1.031 true 0.958,2.333 0.958,2.823 true 2.083,0.396 2.302,0.583 0.219,0.188 10 false A 2.354,1.063 2.615,1.26 0.26,0.198 10 false *1 1.344,0.469 1.573,0.646 0.229,0.177 10 false *1 0.885,2.854 1.125,3.063 0.24,0.208 10 false *2 2.406,1.896 2.625,2.104 0.219,0.208 10 false *2
*1 Engine Surface
*2 Drive Plate Surface


Using a vernier caliper and straightedge, measure dimension A between the transmission contact surface of the engine and the torque converter contact surface of the drive plate.

NOTICE:

Make sure to deduct the thickness of the straightedge.



e.
C193531N02
2.406,0.25 2.604,0.458 0.198,0.208 10 false B

Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the previous step.

Standard:

B = A + 1.00 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the transaxle is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.




Hide 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

C187504C01
2.969,1.083 1.917,1.083 true 0.958,0.99 1.188,1.198 0.229,0.208 10 false *2 3.031,0.99 3.271,1.188 0.24,0.198 10 false *1
*1 Torque Converter Centerpiece
*2 Crankshaft


a.

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter clutch centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1.0 g (0.0353 oz)



b.
C283592N01
0.74,2.823 0.896,3.021 0.156,0.198 10 false A 1.208,2.542 1.365,2.74 0.156,0.198 10 false A 2.094,2.531 2.25,2.729 0.156,0.198 10 false A 2.667,2.865 2.823,3.063 0.156,0.198 10 false A 0.604,3.948 0.76,4.146 0.156,0.198 10 false A 0.719,4.177 0.875,4.375 0.156,0.198 10 false B 0.948,4.365 1.104,4.563 0.156,0.198 10 false B 2.229,4.438 2.385,4.635 0.156,0.198 10 false B 2.729,4.063 2.885,4.26 0.156,0.198 10 false B

Install the transmission to the engine with the 9 bolts.

Torque:
for bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Confirm that the 2 knock pins are installed to the surface of the engine block before installing the transmission.



Hide 5.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.

Turn the crankshaft to gain access to the installation locations of the 6 torque converter clutch setting bolts and install each bolt through the hole of the flywheel while holding the crankshaft pulley bolt with a wrench.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

NOTICE:

Install the black colored bolt first, and then the silver colored 5 bolts.



Hide 6.INSTALL STARTER ASSEMBLY

Hide 7.CONNECT WIRE HARNESS

a.

Connect the 8 connectors and attach the 7 clamps.


b.

Connect the ground cable with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 8.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the engine mounting insulator to the transmission with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 9.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Connect the ends of the No. 3 frame crossmember to the vehicle with the 4 bolts and 4 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


b.

Install the No. 3 frame crossmember to the rear No. 1 engine mounting insulator with the 4 set bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


Hide 10.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the control cable bracket with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 11.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Move the shift lever to N.


b.
C245255N02
1.396,0.052 1.552,0.25 0.156,0.198 10 true N 1.781,0.042 1.938,0.24 0.156,0.198 10 true R 2.146,0.135 2.302,0.333 0.156,0.198 10 true P

Turn the control shaft lever clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.


c.

Connect the transmission control cable to the transmission control cable bracket with a new clip, and then connect the cable end to the control shaft lever with the nut.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 12.INSTALL OIL COOLER TUBE

a.

Loosely install the tip of the inlet oil cooler tube to the automatic transmission by hand.


b.

Loosely install the tip of the outlet oil cooler tube to the automatic transmission by hand.


c.

Install the 2 clamps with the 2 bolts.

Torque:
5.0 N*m (50 kgf*cm, 43 in.*lbf)


d.

Using a union nut wrench, tighten the inlet and outlet oil cooler tubes.

Torque:
34 N*m (346 kgf*cm, 25 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 13.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY

Hide 17.INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY

a.
C213733C02
1.438,1.219 1.75,0.729 1.75,0.729 1.896,0.729 true 1.938,0.646 2.229,0.833 0.292,0.188 10 false *1
*1 Select Return Spring


While pushing the select return spring to the left with the end of the transfer high and low shift lever, insert the end of the shift lever into the shift fork.


b.
C213734C02
2.083,1.063 2.51,0.74 2.51,0.74 2.781,0.74 true 2.813,0.646 3.031,0.833 0.219,0.188 10 false *1
*1 Shift Lever Cap


While holding down the shift lever cap, install the snap ring to install the transfer high and low shift lever.


c.

Return the transfer front drive shift boot to its original position.


Hide 18.INSTALL SHIFT LEVER BOOT ASSEMBLY

a.

Install the shift lever boot with the 4 screws.


Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 24.CHECK FOR EXHAUST GAS LEAKS

Hide 25.INSTALL NO. 3 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 26.INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 27.INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)