1.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY
Make sure that the knock pins are not loose, bent, damaged or scratched.
Align the input shaft with the clutch disc and install the transmission to the engine.
| *A | for TR Engine series |
| *B | for 1KD-FTV, 2KD-FTV |
for TR Engine series:
Install the 7 bolts.
for 1KD-FTV, 2KD-FTV:
Install the 5 bolts.
2.INSTALL STIFFENER PLATE (for 1KD-FTV, 2KD-FTV)
Install the stiffener plate RH with the 4 bolts.
Install the stiffener plate LH with the 4 bolts.
3.INSTALL MANIFOLD STAY (for TR Series Engine)
4.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR
Install the mounting insulator with the 4 bolts.
5.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.
Connect the No. 3 frame crossmember sub-assembly to the No. 1 rear engine mounting insulator.
6.INSTALL STARTER ASSEMBLY
for 2TR-FE: (See page Engine / Hybrid System>2TR-FE STARTING>STARTER(for 1.7 kW Type)>INSTALLATION)
for 2TR-FBE: (See page Engine / Hybrid System>2TR-FBE STARTING>STARTER>INSTALLATION)
for 1KD-FTV: (See page Engine / Hybrid System>1KD-FTV STARTING>STARTER(for BOSCH Made)>INSTALLATION)
for 2KD-FTV DENSO made: (See page Engine / Hybrid System>2KD-FTV STARTING>STARTER(for DENSO Made)>INSTALLATION)
for 2KD-FTV BOSCH made: (See page Engine / Hybrid System>2KD-FTV STARTING>STARTER(for BOSCH Made)>INSTALLATION)
7.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY
Install the clutch release cylinder with the 2 bolts.
8.CONNECT WIRE HARNESS
Connect the back-up light switch connector and speedometer sensor connector.
9.INSTALL FRONT EXHAUST PIPE ASSEMBLY
for 2TR-FE: (See page Engine / Hybrid System>2TR-FE INTAKE / EXHAUST>EXHAUST PIPE>INSTALLATION)
for 2TR-FBE: (See page Engine / Hybrid System>2TR-FBE INTAKE / EXHAUST>EXHAUST PIPE>INSTALLATION)
for 1KD-FTV: (See page Engine / Hybrid System>1KD-FTV INTAKE / EXHAUST>EXHAUST PIPE(w/o DPF)>INSTALLATION)
for 2KD-FTV w/o DPF: (See page Engine / Hybrid System>2KD-FTV INTAKE / EXHAUST>EXHAUST PIPE(w/o DPF)>INSTALLATION)
for 2KD-FTV w/ DPF: (See page Engine / Hybrid System>2KD-FTV INTAKE / EXHAUST>EXHAUST PIPE(w/ DPF)>INSTALLATION)
10.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
11.ADD MANUAL TRANSMISSION OIL
12.INSTALL FLOOR SHIFT LEVER ASSEMBLY
Cover the shift lever cap with a cloth.
Press down on the shift lever cap and rotate it clockwise to install the floor shift lever assembly.
Apply MP grease to the tip of the shift lever.
13.INSTALL SHIFT LEVER BOOT ASSEMBLY
Install the shift lever boot with the 4 screws and 2 clips.
w/o Console Box:
Install the floor carpet, front seat, front door scuff plate, etc.
14.INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box)
15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).