Home › Drivetrain › R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY › from 2012.10
RM1840EF _52 Drivetrain _009614 R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE _0052519 MANUAL TRANSMISSION ASSEMBLY A

R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY

a.

Make sure that the knock pins are not loose, bent, damaged or scratched.


b.

Align the input shaft with the clutch disc and install the transmission to the engine.


c.
C281604
0.26,0.198 0.573,0.396 0.313,0.198 10 false *A 0.229,2.302 0.542,2.5 0.313,0.198 10 false *B 1.281,0.198 1.438,0.396 0.156,0.198 10 false A 2.552,0.219 2.708,0.417 0.156,0.198 10 false A 0.625,1.073 0.781,1.271 0.156,0.198 10 false A 0.76,1.604 0.917,1.802 0.156,0.198 10 false B 1.063,2.031 1.219,2.229 0.156,0.198 10 false B 2.594,1.948 2.75,2.146 0.156,0.198 10 false B 2.854,1.875 3.01,2.073 0.156,0.198 10 false B
*A for TR Engine series
*B for 1KD-FTV, 2KD-FTV


for TR Engine series:

Install the 7 bolts.

Torque:
for bolt A : 72 N*m (729 kgf*cm, 53 ft.*lbf)
for bolt B : 37 N*m (379 kgf*cm, 27 ft.*lbf)


d.

for 1KD-FTV, 2KD-FTV:

Install the 5 bolts.

Torque:
72 N*m (729 kgf*cm, 53 ft.*lbf)


Hide 2.INSTALL STIFFENER PLATE (for 1KD-FTV, 2KD-FTV)

a.

Install the stiffener plate RH with the 4 bolts.

Torque:
72 N*m (729 kgf*cm, 53 ft.*lbf)


b.

Install the stiffener plate LH with the 4 bolts.

Torque:
72 N*m (729 kgf*cm, 53 ft.*lbf)


Hide 4.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the mounting insulator with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 5.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


b.

Connect the No. 3 frame crossmember sub-assembly to the No. 1 rear engine mounting insulator.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 7.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

a.

Install the clutch release cylinder with the 2 bolts.

Torque:
12 N*m (119 kgf*cm, 9 ft.*lbf)


Hide 8.CONNECT WIRE HARNESS

a.

Connect the back-up light switch connector and speedometer sensor connector.


Hide 10.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 12.INSTALL FLOOR SHIFT LEVER ASSEMBLY

a.

Cover the shift lever cap with a cloth.


b.

Press down on the shift lever cap and rotate it clockwise to install the floor shift lever assembly.

HINT:

Apply MP grease to the tip of the shift lever.



Hide 13.INSTALL SHIFT LEVER BOOT ASSEMBLY

a.

Install the shift lever boot with the 4 screws and 2 clips.


b.

w/o Console Box:

Install the floor carpet, front seat, front door scuff plate, etc.


Hide 14.INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box)

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).