Home › Drivetrain › R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY › 2012.04–2012.10
RM1840EF _52 Drivetrain _009614 R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE _0052519 MANUAL TRANSMISSION ASSEMBLY A

R150 / R151 / R156 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box)

Hide 4.REMOVE SHIFT LEVER BOOT ASSEMBLY

a.

w/o Console Box:

Remove the front seat, front door scuff plate, etc. and fold back the floor carpet so that the shift lever can be removed.


b.
G034215
0.677,0.917 0.917,1.115 0.24,0.198 10 true *1 2.531,1.146 2.771,1.344 0.24,0.198 10 true *1 2.448,1.719 2.688,1.917 0.24,0.198 10 true *1 0.677,1.688 0.917,1.885 0.24,0.198 10 true *1 2.396,0.688 2.635,0.885 0.24,0.198 10 true *2 0.781,0.448 1.021,0.646 0.24,0.198 10 true *2
*1 Screw
*2 Clip


Remove the 4 screws, 2 clips and shift lever boot assembly.


Hide 5.REMOVE FLOOR SHIFT LEVER ASSEMBLY

a.
G021695
1.177,1.094 0.708,1.729 true 0.583,1.771 0.75,1.927 0.167,0.156 10 false *1 2.646,0.083 2.875,0.281 0.229,0.198 10 false *a 2.708,1.792 2.875,1.938 0.167,0.146 10 false *b
*1 Cloth
*a Press down
*b Rotate counterclockwise


Cover the shift lever cap with a cloth.


b.

Press down on the shift lever cap and rotate it counterclockwise to remove it.


c.

Pull out the shift lever.


Hide 6.REMOVE NO. 1 ENGINE UNDER COVER

Hide 7.REMOVE NO. 2 ENGINE UNDER COVER

Hide 9.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 11.DISCONNECT WIRE HARNESS

a.

Disconnect the back-up light switch connector and speedometer sensor connector.


Hide 12.DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

a.
G034217

Remove the 2 bolts and disconnect the release cylinder assembly.


Hide 14.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Support the transmission rear side with a support stand.


b.
C180320

Remove the 4 set bolts of the rear No. 1 engine mounting insulator.


c.
C180319

Remove the 4 bolts, 4 nuts and No. 3 frame crossmember sub-assembly.


Hide 15.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
G034219

Remove the 4 bolts and mounting insulator.


Hide 16.REMOVE MANIFOLD STAY (for TR Series Engine)

Hide 17.REMOVE STIFFENER PLATE (for 1KD-FTV, 2KD-FTV)

a.
C281602

Remove the 4 bolts and stiffener plate RH.


b.

Remove the 4 bolts and stiffener plate LH.


Hide 18.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY

a.

Using a transmission jack, support the transmission.


b.

Remove the support stand from the transmission.


c.
C238790
0.302,2.208 0.51,2.417 0.208,0.208 10 false *B 0.302,0.135 0.51,0.344 0.208,0.208 10 false *A
*A for TR Engine series
*B for 1KD-FTV, 2KD-FTV


for 1KD-FTV, 2KD-FTV:

Remove the 5 bolts and transmission.


d.

for TR Engine series:

Remove the 7 bolts and transmission.