Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2011.10–2012.01
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

When one of the following conditions is met, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

The vacuum inside the brake booster decreases.

·

There is an open circuit in the harness between the combination meter and the skid control ECU (brake actuator assembly).

·

EBD operation has been disabled.


WIRING DIAGRAM

C238265
0.365,0.698 1.313,0.917 0.948,0.219 10 false from IG Circuit 0.167,1.615 1.094,1.844 0.927,0.229 10 false from IG Circuit 2.052,0.865 3.188,1.073 1.135,0.208 10 false ECU-IG&GAUGE 2.99,1.583 3.938,1.802 0.948,0.219 10 false Reverse Circuit 2.25,1.802 2.667,1.969 0.417,0.167 10 false Brake 1.563,1.521 1.76,1.688 0.198,0.167 10 false 21 2.031,3.323 2.167,3.49 0.135,0.167 10 false 2 3.229,4.802 3.365,4.969 0.135,0.167 10 false 2 3.229,3.323 3.365,3.49 0.135,0.167 10 false 1 2.063,4.802 2.198,4.969 0.135,0.167 10 false 1 3.229,6.188 3.365,6.354 0.135,0.167 10 false 1 4.563,1.521 4.76,1.688 0.198,0.167 10 false 26 5.417,0.594 5.615,0.76 0.198,0.167 10 false 34 5.417,4.771 5.615,4.938 0.198,0.167 10 false 29 5.458,1.521 5.604,1.688 0.146,0.167 10 false 8 5.458,3.313 5.604,3.479 0.146,0.167 10 false 1 4.563,1.99 4.76,2.156 0.198,0.167 10 false 36 2.156,2.573 4.073,2.792 1.917,0.219 10 false Combination Meter Assembly 2.156,2.417 2.667,2.583 0.51,0.167 10 false G19 1.906,3.74 2.323,3.906 0.417,0.167 10 false A18 1.906,3.885 4.448,4.271 2.542,0.385 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly) 5.406,6.479 5.823,6.646 0.417,0.167 10 false A36 5.406,6.635 6.969,7.021 1.563,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 1.906,5.146 2.323,5.313 0.417,0.167 10 false A37 1.906,5.313 4.115,5.521 2.208,0.208 10 false Vacuum Warning Switch Assembly 1.906,6.604 2.323,6.771 0.417,0.167 10 false K6 1.906,6.771 3.938,7 2.031,0.229 10 false Parking Brake Switch Assembly 5.698,0.719 6.115,0.885 0.417,0.167 10 false IG1 5.698,1.615 6.115,1.781 0.417,0.167 10 false BRL 5.698,4.885 6.115,5.052 0.417,0.167 10 false PKB 5.698,3.438 6.115,3.604 0.417,0.167 10 false GND1 4.135,1.531 4.552,1.698 0.417,0.167 10 false PKBI 4.219,2 4.563,2.167 0.344,0.167 10 false SW 1.792,1.542 2.083,1.708 0.292,0.167 10 false IG+

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.
C199357
0.156,0.958 0.51,1.198 0.354,0.24 2.073,1.927 2.146,1.927 2.146,1.927 2.302,1.396 false 0.146,0.063 0.458,0.219 0.313,0.156 10 false *a 0.219,1 0.594,1.26 0.375,0.26 10 false A36 1.823,1.854 2.198,2.115 0.375,0.26 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A36-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK BRAKE BOOSTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK BRAKE BOOSTER ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

REPLACE BRAKE BOOSTER ASSEMBLY

6.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.

Turn the ignition switch to ON.


b.

With the brake fluid at the specified level, disconnect the brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector and check the brake warning light.

Result:
Result Proceed to
Brake warning light does not turn off A
Brake warning light turns off B


HINT:

If the brake warning light turns off, the brake fluid level warning switch (brake master cylinder reservoir sub-assembly) has an internal short circuit.




A

7.CHECK VACUUM WARNING SWITCH ASSEMBLY

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

7.CHECK VACUUM WARNING SWITCH ASSEMBLY
a.

Start the engine.


b.

Idle the engine.


c.

Disconnect the vacuum warning switch connector and check the brake warning light.

Result:
Result Proceed to
Brake warning light does not turn off A
Brake warning light turns off B


HINT:

If the brake warning light turns off, the vacuum warning switch has an internal short circuit.




A

8.INSPECT PARKING BRAKE SWITCH ASSEMBLY

B

REPLACE VACUUM WARNING SWITCH ASSEMBLY

8.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.

Turn the ignition switch off.


b.

Remove the parking brake switch assembly.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>REMOVAL


c.

Inspect the parking brake switch.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER AND PARKING BRAKE SWITCH)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER AND PARKING BRAKE SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G19 combination meter connector.


d.

Disconnect the parking brake switch connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A36-8 (BRL) - G19-26 (PKBI) Always Below 1 Ω
A36-8 (BRL) - Body ground Always 10 kΩ or higher
A36-29 (PKB) - K6-1 Always Below 1 Ω
A36-29 (PKB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BODY GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the G19 combination meter connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Disconnect the brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


e.

Disconnect the vacuum warning switch connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-36 (SW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Brake Warning Light Brake warning light Warning light ON / OFF Observe the combination meter.
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Brake Warning Light
50004 105 12

f.

When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light ON or OFF ON: Brake warning light on
OFF: Brake warning light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Brake Warning Light
50003 105 52
Result:
Result Proceed to
Data List Display Data List Display When Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B




A

B

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)