Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2012.10
RM1840EF _58 Vehicle Interior _009641 THEFT DETERRENT / KEYLESS ENTRY _0052688 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Starter Relay Circuit  


DESCRIPTION

When the theft deterrent system operates, the theft warning ECU assembly deactivates the ST relay so that the starter cannot crank the engine.

WIRING DIAGRAM

B276451
5.698,3.406 5.979,3.573 0.281,0.167 10 false G29 5.875,2.865 6.156,3.031 0.281,0.167 10 false E 5.698,2.792 5.823,2.958 0.125,0.167 10 false 1 5.875,0.396 6.271,0.563 0.396,0.167 10 false SRLY 5.635,0.313 5.833,0.479 0.198,0.167 10 false 12 4.656,0.313 4.781,0.479 0.125,0.167 10 false 2 3.823,0.302 3.948,0.469 0.125,0.167 10 false 1 3.552,0.302 3.719,0.469 0.167,0.167 10 false *1 3.646,0.781 3.813,0.948 0.167,0.167 10 false *2 3.177,0.771 3.302,0.938 0.125,0.167 10 false 5 2.552,0.771 2.677,0.938 0.125,0.167 10 false 4 0.354,0.667 0.479,0.833 0.125,0.167 10 false 7 0.75,1.104 0.958,1.271 0.208,0.167 10 false G9 0.75,1.25 1.74,1.74 0.99,0.49 10 false Ignition Switch Assembly 2.219,1.135 2.51,1.302 0.292,0.167 10 false C57 2.219,1.271 3.542,1.76 1.323,0.49 10 false Park/Neutral Position Switch Assembly 0.073,3.354 0.958,3.646 0.885,0.292 10 false from Battery 0.135,3.927 2.083,4.094 1.948,0.167 10 false *1: for Manual Transmission 0.135,4.177 2.448,4.344 2.313,0.167 10 false *2: for Automatic Transmission 0.365,1.917 0.49,2.083 0.125,0.167 10 false 5 0.188,1.698 0.521,1.865 0.333,0.167 10 false AM2 0.208,0.875 0.5,1.042 0.292,0.167 10 false ST2 1.635,0.51 1.844,0.677 0.208,0.167 10 false ST 4.188,2.406 4.396,2.573 0.208,0.167 10 false ST 4.656,2 4.781,2.167 0.125,0.167 10 false 3 3.823,1.99 3.927,2.156 0.104,0.167 10 false 5 5.719,3.594 6.917,3.969 1.198,0.375 10 false Theft Warning ECU Assembly 2.99,2.75 3.75,2.927 0.76,0.177 10 false from Starter

CAUTION / NOTICE / HINT

NOTICE:
·

If the engine cranks but does not start, there is a problem with the SFI system*1 or ECD system*2. If this is the case, refer to SFI System*1 or ECD System*2 and perform troubleshooting.

*1: for 2TR-FE, 2TR-FBE, 1GR-FE

*2: for 1KD-FTV, 2KD-FTV


·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the theft warning ECU assembly, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(for Built-in Type Door Control Receiver)>REGISTRATION).



PROCEDURE

1.INSPECT ST RELAY
a.
B205010
0.104,0.156 0.417,0.313 0.313,0.156 10 false *A 0.135,2.646 0.448,2.802 0.313,0.156 10 false *B 0.385,1.052 0.604,1.229 0.219,0.177 10 false 3 2.76,1.771 2.979,1.948 0.219,0.177 10 false 3 2.406,3.594 2.677,3.833 0.271,0.24 10 false 3 0.406,3.344 0.677,3.583 0.271,0.24 10 false 3 0.396,1.583 0.542,1.76 0.146,0.177 10 false 1 2.615,0.917 2.802,1.083 0.188,0.167 10 false 1 2.177,3.271 2.365,3.438 0.188,0.167 10 false 1 0.417,3.875 0.604,4.042 0.188,0.167 10 false 1 1.385,1.042 1.542,1.24 0.156,0.198 10 false 5 1.375,3.354 1.531,3.552 0.156,0.198 10 false 5 2.76,3.865 2.917,4.063 0.156,0.198 10 false 5 2.75,1.292 2.906,1.49 0.156,0.198 10 false 5 1.385,1.594 1.604,1.833 0.219,0.24 10 false 2 1.375,3.875 1.594,4.115 0.219,0.24 10 false 2 2.188,3.906 2.406,4.146 0.219,0.24 10 false 2 2.292,0.917 2.51,1.156 0.219,0.24 10 false 2
*A for 2TR-FE, 2TR-FBE, 1GR-FE
*B for 1KD-FTV, 2KD-FTV


Remove the ST relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPLACE ST RELAY

2.INSPECT IGNITION SWITCH ASSEMBLY
a.
B275965
0.896,1.76 1.219,1.76 1.219,1.76 1.417,1.344 false 1.99,1.344 2.25,1.813 2.25,1.813 2.458,1.813 false 0.604,1.677 1.063,1.875 0.458,0.198 10 false ST2 2.51,1.729 2.969,1.927 0.458,0.198 10 false AM2

Remove the ignition switch assembly.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (AM2) - 7 (ST2) Off, ACC, ON 10 kΩ or higher
Start Below 1 Ω


HINT:

If replacing the park/neutral position switch assembly, refer to the procedures below.




Resul:
Proceed to
OK
NG



OK

3.CHECK VEHICLE TYPE

NG

REPLACE IGNITION SWITCH ASSEMBLY

3.CHECK VEHICLE TYPE
a.

Check the vehicle type.

Result:
Result Proceed to
for Automatic Transmission A
for Manual Transmission B




A

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

5.CHECK HARNESS AND CONNECTOR (ST RELAY - BATTERY)
4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 - 5 Shift lever in P or N Below 1 Ω
Shift lever not in P and N 10 kΩ or higher


Result:
Result Proceed to
OK A
NG (for A750F) B
NG (for A340F) C
NG (for A343F) D
NG (for A343E) E




A

5.CHECK HARNESS AND CONNECTOR (ST RELAY - BATTERY)

B

C

D

E

5.CHECK HARNESS AND CONNECTOR (ST RELAY - BATTERY)
a.
B276697
0.344,0.708 0.656,0.865 0.313,0.156 10 false *A 2,0.708 2.313,0.865 0.313,0.156 10 false *B 0.073,0.104 0.385,0.26 0.313,0.156 10 false *a
*A for 2TR-FE, 2TR-FBE, 1GR-FE
*B for 1KD-FTV, 2KD-FTV
*a Front view of wire harness connector
(to ST Relay)


Remove the ST relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay block ST relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)
a.
B274165
0.24,1.177 0.656,1.531 0.417,0.354 0.396,0.896 0.563,0.896 0.563,0.896 0.865,1.208 true 2.271,1.198 2.552,0.729 2.552,0.729 2.729,0.729 true 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.26,0.823 0.417,1.021 0.156,0.198 10 false E 2.771,0.646 3.385,0.844 0.615,0.198 10 false SRLY 0.313,1.271 0.771,1.469 0.458,0.198 10 false G29
*a Front view of wire harness connector
(to Theft Warning ECU Assembly)


Disconnect the G29 theft warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G29-1 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G29-12 (SRLY) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR