Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING(for Single Cab) › from 2012.10
RM1840EF _58 Vehicle Interior _009650 INTERIOR PANELS / TRIM _0052775 ROOF HEADLINING(for Single Cab) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for Single Cab)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL REAR NO. 2 SIDE RAIL SPACER LH

a.

Attach the 2 claws to install the rear No. 2 side rail spacer.


Hide 2.INSTALL REAR NO. 2 SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.


Hide 3.INSTALL SIDE RAIL SPACER

a.

Attach the 2 claws to install the side rail spacer.


Hide 4.INSTALL FRONT SIDE RAIL SPACER LH

a.

Attach the 2 claws to install the front side rail spacer.


Hide 5.INSTALL FRONT SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.


Hide 6.INSTALL ROOF HEADLINING ASSEMBLY

B278254

a.

Place the roof headlining into the vehicle as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when placing it.



b.

Install the roof headlining with the 5 clips.


c.

Connect the connectors and attach the 4 clamps.


d.

Attach the 4 clamps to the front pillar.


Hide 11.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 12.INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 13.INSTALL ASSIST GRIP

a.

Install the assist grip with the 2 screws.


b.

Attach the 4 claws to close the 2 covers.


Hide 14.INSTALL VISOR HOLDER LH

a.

Attach the 2 claws to install the visor holder.


b.

Install the screw.


Hide 15.INSTALL VISOR HOLDER RH

HINT:

Use the same procedure described for the LH side.


Hide 16.INSTALL VISOR ASSEMBLY LH

a.

Install the visor with the 2 screws.


b.

Attach the guide.


Hide 17.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 18.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 19.INSTALL QUARTER INSIDE TRIM BOARD LH

a.

Attach the 3 clips to install the quarter inside trim board.


b.

Connect the front seat belt shoulder anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Attach the 2 claws to close the front seat belt shoulder anchor cover.


Hide 20.INSTALL QUARTER INSIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 21.INSTALL LOWER QUARTER TRIM PANEL LH

a.

Attach the 3 clips, claw and 2 guides to install the lower quarter trim panel.


b.

Connect the front seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 22.INSTALL LOWER QUARTER TRIM PANEL RH

HINT:

Use the same procedure described for the LH side.


Hide 23.INSTALL UPPER BACK PANEL GARNISH

a.

Attach the 5 clips, 4 guides and 4 claws to install the upper back panel garnish.


Hide 24.INSTALL FRONT PILLAR GARNISH LH

a.

Attach the 2 guides and 2 clips to install the front pillar garnish.


Hide 25.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 26.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for both front assist grips.


a.

Install the front assist grip with the 2 screws.


Hide 27.INSTALL ASSIST GRIP PLUG LH

HINT:

Use the same procedure for both front No. 1 assist grip plug.


a.

Attach the 2 claws to install the front No. 1 assist grip plug.


Hide 28.INSTALL ASSIST GRIP PLUG RH

HINT:

Use the same procedure described for the LH side.


Hide 29.INSTALL FRONT DOOR OPENING TRIM LH

B277003
2.813,1.49 2.781,1.26 2.781,1.26 2.885,1.26 false 2.938,1.167 3.104,1.313 0.167,0.146 10 false *1 1.323,0.604 1.542,0.823 0.219,0.219 10 false *2 2.583,0.917 2.771,1.094 0.188,0.177 10 false *2
*1 Paint Mark
*2 Mark Position


a.

Align the paint mark on the front door opening trim with the mark position on the vehicle and install the front door opening trim as shown in the illustration.


Hide 30.INSTALL FRONT DOOR OPENING TRIM RH

HINT:

Use the same procedure described for the LH side.


Hide 31.INSTALL FRONT DOOR SCUFF PLATE LH

a.

Attach the 4 clips and 8 claws to install the front door scuff plate.


Hide 32.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 34.INSTALL FRONT SEAT ASSEMBLY RH

a.

for Manual Seat:

HINT:

Use the same procedure described for the LH side.




Hide 35.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 36.CHECK SRS WARNING LIGHT (w/ Airbag System)