Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL › from 2012.10
RM1840EF _58 Vehicle Interior _009650 INTERIOR PANELS / TRIM _0052774 LOWER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  LOWER INSTRUMENT PANEL  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 1.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

a.

for Automatic Air Conditioning System:

Connect the room temperature sensor.


b.

Attach the 2 guides to install the lower instrument panel.


c.

Connect the connectors and attach the clamps.


d.

Connect the hood lock control cable, fuel lid lock control cable and DLC3.


e.

Install the 2 bolts <C>, nut <D> and 3 screws <E>.


f.

Install the 2 clips <B>.

B278247
6.479,1.115 6.656,1.281 0.177,0.167 10 false *1 1,2.76 1.177,2.927 0.177,0.167 10 false *1 6.281,2.479 6.458,2.646 0.177,0.167 10 false *2 1.281,3.813 1.458,3.979 0.177,0.167 10 false *2 2.927,1.406 3.104,1.573 0.177,0.167 10 true *3 5.125,2.677 5.302,2.844 0.177,0.167 10 false *4 3.885,3.354 4.063,3.521 0.177,0.167 10 false *4 5.104,0.49 5.281,0.656 0.177,0.167 10 false *4 2.219,3.448 2.396,3.615 0.177,0.167 10 false *5 1.75,3.49 1.927,3.656 0.177,0.167 10 true *6 2.5,3.281 2.677,3.448 0.177,0.167 10 false *7 4.969,3.969 5.146,4.135 0.177,0.167 10 true *8 3.313,5.021 3.521,5.188 0.208,0.167 10 true *8 2.281,5.052 2.458,5.219 0.177,0.167 10 true *8 3.969,5 4.146,5.167 0.177,0.167 10 true *8 5.771,1.146 5.948,1.313 0.177,0.167 10 true *9 1.823,2.344 2,2.51 0.177,0.167 10 true *9 3.917,2.052 4.094,2.219 0.177,0.167 10 true *8
*1 Clip <B> *2 Bolt <C>
*3 Nut <D> *4 Screw <E>
*5 Hood Lock Control Cable *6 Fuel Lid Lock Control Cable
*7 DLC3 *8 Clamp
*9 Guide - -



Hide 2.INSTALL NO. 1 SWITCH HOLE BASE

a.

Attach the 5 claws to install the No. 1 switch hole base.


Hide 3.INSTALL SWITCH BASE

a.

Connect the connectors.


b.

Attach the 8 claws to install the switch base.


Hide 4.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (w/o Front Passenger Airbag)

Hide 5.INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL (w/o Console Box, w/o Console Box Lid)

a.

Attach the 3 claws to install the lower center instrument panel finish panel.


b.

Install the 2 clips <B>.


Hide 7.INSTALL NO. 1 INSTRUMENT PANEL BOX

a.

Connect the connectors and attach the clamp.


b.

Install the No. 1 instrument panel box with the 6 screws <A>.


Hide 8.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

a.

Attach the 3 guides, 2 claws and 3 clips to install the lower instrument panel finish panel.


Hide 12.INSTALL COWL SIDE TRIM BOARD LH

a.

Attach the 2 clips to install the cowl side trim board.


b.

Install the clip.


c.

Install the front door opening trim.


Hide 13.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 15.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 16.INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 17.INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 18.INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 20.CHECK SRS WARNING LIGHT (w/ Airbag System)