Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  


DESCRIPTION

HINT:

If DTC P0011 or P0012 is output, check the Variable Valve Timing (VVT) system.


The VVT system includes the ECM, oil control valve and VVT controller. The ECM sends a target duty cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure applied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve assembly based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the camshaft timing oil control valve assembly. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A192077E04
4.427,0.815 6.408,1.027 1.981,0.212 10 Camshaft Position Sensor 4.427,1.325 6.521,1.486 2.094,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.268 1.551,0.253 10 VVT System: 2.333,1.96 3.61,2.135 1.277,0.175 10 Target Valve Timing 2.333,1.287 3.61,1.462 1.277,0.175 10 Actual Valve Timing 2.683,2.695 3.397,2.87 0.714,0.175 10 Correction 2.822,3.204 3.224,3.379 0.402,0.175 10 ECM 1.599,3.747 4.516,3.922 2.917,0.175 10 Camshaft Timing Oil Control Valve Assembly 0.166,2.69 0.861,2.865 0.695,0.175 10 Duty Cycle 4.427,1.827 6.017,1.981 1.589,0.154 10 Mass Air Flow Meter 4.427,2.854 6.78,3.043 2.353,0.189 10 Engine Coolant Temperature Sensor 4.427,2.344 6.211,2.512 1.784,0.168 10 Throttle Position Sensor 4.427,3.353 6.169,3.507 1.742,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 6.982,4.401 3.323,0.184 10 VVT Controller (Camshaft Timing Gear Assembly) 3.883,4.917 4.984,5.101 1.101,0.184 10 Intake Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) Valve timing is not adjusted in the valve timing advance range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


Comes on DTC stored
P0012 Camshaft Position "A" - Timing Over-Retarded (Bank 1) Valve timing is not adjusted in the valve timing retard range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


Comes on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC remains stored for a short time even after the system returns to normal. These foreign objects may then be captured by the oil filter.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0012)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.

Result:
Result Proceed to
DTC P0011 or P0012 is output A
DTC P0011 or P0012 and other DTCs are output B


HINT:

If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).

Powertrain > Engine and ECT > Active Test
Tester Display
Control the VVT Linear (Bank1)
50004 234 32

e.

Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.

HINT:
·

When performing the Active Test, make sure the air conditioning is on.

·

Make sure the engine coolant temperature when the engine is started is 30°C (86°F) or less.



OK:
Tester Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [VVT OCV Duty #1 and VVT Change Angle #1].

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Start the engine and warm it up.


f.

Switch the ECM from normal mode to check mode using the tester.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Allow the engine to idle for more than 1 minute.


h.

Drive the vehicle for more than 10 minutes.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

j.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0011 or P0012 is output B


HINT:

DTC P0011 or P0012 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes remain stored for a short time even after the system returns to normal. These foreign objects may then be captured by the oil control valve filter, thus eliminating the source of the problem.




A

B

7.ADJUST VALVE TIMING
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


b.
A183795E21
0.135,0.094 2.615,0.313 2.479,0.219 10 false Component without harness connected: 0.146,0.281 2.333,0.719 2.188,0.438 10 false (Camshaft Timing Oil Control Valve Assembly) 0.219,1.323 1.531,1.552 1.313,0.229 10 false Valve moves quickly

Connect the positive (+) battery terminal to terminal 1 and the negative (-) battery terminal to terminal 2. Check the valve operation.

OK:

Valve moves quickly.



c.

Reinstall the camshaft timing oil control valve assembly.


Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
a.

Inspect the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2TR-FBE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


Result:
Proceed to
OK
NG



OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

6.INSPECT OIL CONTROL VALVE FILTER
a.

Remove the oil control valve filter.


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



c.

Reinstall the oil control valve filter.


Result:
Proceed to
OK
NG



OK

7.ADJUST VALVE TIMING

NG

REPLACE OIL CONTROL VALVE FILTER

7.ADJUST VALVE TIMING
HINT:

There are no marks on the cylinder head to align for the purpose of checking valve timing. Valve timing can only be inspected by aligning the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and reinstall the chain to align the timing marks.

Click hereEngine / Hybrid System>2TR-FBE ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011 OR P0012)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Start the engine and warm it up.


f.

Switch the ECM from normal mode to check mode using the tester.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Allow the engine to idle for more than 1 minute.


h.

Drive the vehicle for more than 10 minutes.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

j.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0011 or P0012 is output B


HINT:

DTC P0011 or P0012 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes remain stored for a short time even after the system returns to normal. These foreign objects may then be captured by the oil control valve filter, thus eliminating the source of the problem.




A

END

B