Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  


DESCRIPTION

The Variable Valve Timing (VVT) system controls the intake camshaft and exhaust camshaft to achieve optimal valve timing according to various driving conditions. This control is performed based on the intake air volume, throttle valve position, engine coolant temperature and other engine operating conditions. The ECM controls the camshaft timing oil control valves based on the signals transmitted by several sensors. As a result, the relative positions of the camshafts are optimized, improving engine torque and fuel economy and reducing exhaust emissions. In addition, the ECM detects the actual valve timing based on the signals from the VVT sensors and performs feedback control, achieving optimal valve timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) A deviation in the crankshaft position sensor signal and VVT sensor (bank 1) signal (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


Comes on DTC stored

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0016.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read DTCs.

Result:
Result Proceed to
DTC P0016 is output A
DTC P0016 and other DTCs are output B


HINT:

If any DTCs other than P0016 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).

Powertrain > Engine and ECT > Active Test
Tester Display
Control the VVT Linear (Bank1)
50004 234 32

e.

Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.

HINT:
·

When performing the Active Test, make sure the air conditioning is on.

·

Make sure the engine coolant temperature when the engine is started is 30°C (86°F) or less.



OK:
Tester Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [VVT OCV Duty #1 and VVT Change Angle #1].

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Start the engine and warm it up.


f.

Switch the ECM from normal mode to check mode using the tester.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Allow the engine to idle for more than 1 minute.


h.

Drive the vehicle for more than 10 minutes.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

j.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0016 is output B


HINT:

DTC P0016 is stored when foreign objects in the engine oil are caught in some parts of the system. This code remains stored for a short time even after the system returns to normal. These foreign objects may then be captured by the oil control valve filter, thus eliminating the source of the problem.




A

B

7.ADJUST VALVE TIMING
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


b.
A183795E21
0.135,0.094 2.615,0.313 2.479,0.219 10 false Component without harness connected: 0.146,0.281 2.333,0.719 2.188,0.438 10 false (Camshaft Timing Oil Control Valve Assembly) 0.219,1.323 1.531,1.552 1.313,0.229 10 false Valve moves quickly

Connect the positive (+) battery terminal to terminal 1 and the negative (-) battery terminal to terminal 2. Check the valve operation.

OK:

Valve moves quickly.



c.

Reinstall the camshaft timing oil control valve assembly.


Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
a.

Inspect the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2TR-FBE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


Result:
Proceed to
OK
NG



OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

6.INSPECT OIL CONTROL VALVE FILTER
a.

Remove the oil control valve filter.


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



c.

Reinstall the oil control valve filter.


Result:
Proceed to
OK
NG



OK

7.ADJUST VALVE TIMING

NG

REPLACE OIL CONTROL VALVE FILTER

7.ADJUST VALVE TIMING
HINT:

There are no marks on the cylinder head to align for the purpose of checking valve timing. Valve timing can only be inspected by aligning the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and reinstall the chain to align the timing marks.

Click hereEngine / Hybrid System>2TR-FBE ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Start the engine and warm it up.


f.

Switch the ECM from normal mode to check mode using the tester.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Allow the engine to idle for more than 1 minute.


h.

Drive the vehicle for more than 10 minutes.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

j.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0016 is output B




A

END

B