Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P101D  A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P2195).

HINT:
·

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

·

The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A227661
0.167,1.094 1.094,1.49 0.927,0.396 10 false from Battery 0.271,2.625 0.948,3.042 0.677,0.417 10 false from MAIN Relay 1.313,1.25 1.625,1.448 0.313,0.198 10 false A/F 2.281,2.115 2.604,2.313 0.323,0.198 10 false A/F 0.094,0.073 3.458,0.354 3.365,0.281 8 false Reference (System Diagram of Sensor 1): 3.438,2.375 5.083,2.594 1.646,0.219 10 false Air Fuel Ratio Sensor 3.469,0.979 3.75,1.188 0.281,0.208 10 false +B 3.323,1.646 3.76,1.844 0.438,0.198 10 false A1A- 4.5,0.979 5.031,1.177 0.531,0.198 10 false HA1A 5.219,0.979 5.75,1.177 0.531,0.198 10 false HA1A 4.521,1.646 4.979,1.844 0.458,0.198 10 false A1A+ 5.219,1.646 5.677,1.844 0.458,0.198 10 false A1A+ 5.219,2.854 5.854,3.125 0.635,0.271 10 false A1A- 3.865,1.271 4.5,1.469 0.635,0.198 10 false Heater 3.844,1.948 4.458,2.146 0.615,0.198 10 false Sensor 5.896,0.417 6.375,0.615 0.479,0.198 10 false ECM 6.385,1.854 6.865,2.26 0.479,0.406 10 false Duty Control



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) The heater current is below the specified value while the heater is operating (1 trip detection logic).
·

Open in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM power source circuit

·

ECM


Comes on DTC stored
P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) An air fuel ratio sensor heater current failure (1 trip detection logic).
·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM power source circuit

·

ECM


Comes on DTC stored
P101D A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON The heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM Comes on DTC stored

HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air-fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the Three-Way Catalytic Converter (TWC) to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air-fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.
G038638
2.031,1.083 2.448,0.667 false 1.385,1.115 0.906,0.688 false 1.375,1.615 0.958,1.927 false 2.042,1.604 2.365,1.885 false 2.354,0.49 2.917,0.76 0.563,0.271 10 false HA1A 0.781,0.51 1.094,0.708 0.313,0.198 10 false +B 0.667,1.917 1.083,2.167 0.417,0.25 10 false A1A- 2.25,1.917 2.667,2.167 0.417,0.25 10 false A1A+

Disconnect the air fuel ratio sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (HA1A) - 2 (+B) 20°C (68°F) 1.6 to 3.2 Ω
1 (HA1A) - 4 (A1A-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)
a.
A100209
0.625,0.979 0.958,1.188 0.333,0.208 2.406,0.563 1.938,0.917 false 0.094,0.042 0.344,0.26 0.25,0.219 10 false *a 2.458,0.438 2.823,0.698 0.365,0.26 10 false +B 0.677,1.01 1.042,1.271 0.365,0.26 10 false C85
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C85-2 (+B) - Body ground Ignition switch ON 11 to 14 V



d.

Reconnect the air fuel ratio sensor connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY (A/F)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C85-1 (HA1A) - C97-6 (HA1A) Always Below 1 Ω


Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C85-1 (HA1A) or C97-6 (HA1A) - Body ground Always 10 kΩ or higher



d.

Reconnect the air fuel ratio sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Clear DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Start the engine.


f.

Allow the engine to idle for 1 minute or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0031, P0032 or P101D is output B




A

B

5.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY (A/F)
a.
B060778
2.531,1.125 2.927,1.125 false 2.531,1.625 2.927,1.625 false 2.625,0.573 2.75,0.229 false 2,0.552 1.854,0.208 false 0.24,1.313 0.396,1.51 0.156,0.198 10 false 2 1.198,0.76 1.354,0.958 0.156,0.198 10 false 5 0.24,0.771 0.396,0.969 0.156,0.198 10 false 3 1.198,1.313 1.354,1.51 0.156,0.198 10 false 1 1.792,0.042 1.948,0.24 0.156,0.198 10 false 1 2.729,0.042 2.885,0.24 0.156,0.198 10 false 2 2.99,1.042 3.146,1.24 0.156,0.198 10 false 5 2.99,1.542 3.146,1.74 0.156,0.198 10 false 3

Inspect the A/F relay.

i.

Remove the A/F relay from the engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Always 10 kΩ or higher
3 - 5 Always Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)




Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (A/F SENSOR - A/F RELAY, A/F RELAY - INTEGRATION RELAY)

NG

REPLACE AIR FUEL RATIO SENSOR HEATER RELAY (A/F)

6.CHECK HARNESS AND CONNECTOR (A/F SENSOR - A/F RELAY, A/F RELAY - INTEGRATION RELAY)
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the A/F relay from the engine room relay block.


c.

Remove the integration relay from the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C85-2 (+B) - A/F relay terminal (3) Always Below 1 Ω
A/F relay terminal (5) - 1H-1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C85-2 (+B) or A/F relay terminal (3) - Body ground Always 10 kΩ or higher
A/F relay terminal (5) or 1H-1 - Body ground Always 10 kΩ or higher



e.

Reconnect the air fuel ratio sensor connector.


f.

Reinstall the integration relay.


g.

Reinstall the A/F relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR