Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  


DESCRIPTION

Refer to DTC P0136 (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P0136).

HINT:
·

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.

·

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. The ECM continues operating in fail-safe mode until the ignition switch is turned off.



A303366
0.135,0.125 2.802,0.375 2.667,0.25 10 false Reference (System Diagram of Sensor 2): 0.167,0.667 0.656,1.052 0.49,0.385 10 false from Battery 1.302,0.854 1.573,1.042 0.271,0.188 10 false EFI 2.177,1.885 2.563,2.094 0.385,0.208 10 false MAIN 0.792,2.99 1.302,3.198 0.51,0.208 10 false Ground 3.698,0.594 3.927,0.781 0.229,0.188 10 false +B 3.698,1.271 3.927,1.458 0.229,0.188 10 false E2 4.75,0.604 5.229,0.802 0.479,0.198 10 false HT1B 4.75,1.271 5.229,1.469 0.479,0.198 10 false OX1B 5.333,0.604 5.813,0.802 0.479,0.198 10 false HT1B 5.323,1.271 5.802,1.469 0.479,0.198 10 false OX1B 4.083,0.896 4.573,1.135 0.49,0.24 10 false Heater 4.073,1.583 4.563,1.813 0.49,0.229 10 false Sensor 3.688,1.99 5.177,2.229 1.49,0.24 10 false Heated Oxygen Sensor 5.292,2.313 5.771,2.51 0.479,0.198 10 false EX1B 5.313,2.656 5.792,2.854 0.479,0.198 10 false MREL 6.01,3.156 6.49,3.354 0.479,0.198 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) The heater current is below the specified value while the heater is operating (1 trip detection logic).
·

Open in heated oxygen sensor heater circuit

·

Heated oxygen sensor heater

·

ECM power source circuit

·

ECM


Comes on DTC stored
P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) The heater current is higher than the specified value while the heater is operating (1 trip detection logic).
·

Short in heated oxygen sensor heater circuit

·

Heated oxygen sensor heater

·

ECM power source circuit

·

ECM


Comes on DTC stored
P102D O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON The heater current is higher than the specified value while the heater is not operating (1 trip detection logic). ECM Comes on DTC stored

HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated oxygen sensor heater range check (P0037, P0038 and P102D):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.




CONFIRMATION DRIVING PATTERN

A198819
0.75,1.031 1.5,1.354 0.75,0.323 10 false 3000 rpm 0.979,1.74 1.469,2 0.49,0.26 10 false Idling 0.167,2.042 1.5,2.365 1.333,0.323 10 false Ignition Switch ON 1.927,2.156 2.25,2.406 0.323,0.25 10 false [A] 2.76,1.625 3.021,1.885 0.26,0.26 10 false [B] 4.042,0.865 4.344,1.104 0.302,0.24 10 false [C] 5.385,1.604 5.719,1.875 0.333,0.271 10 false [D] 2.344,2.594 3.604,2.844 1.26,0.25 10 false 5 minutes or more 4.844,2.604 6.021,2.844 1.177,0.24 10 false 5 minutes or more 3.885,2.615 4.583,2.823 0.698,0.208 10 false 1 minute 5.958,3.031 6.323,3.354 0.365,0.323 10 false [E]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) [A].

4.

Start the engine and idle it for 5 minutes or more [B].

5.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

6.

Idle the engine for 5 minutes or more [D].

7.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

8.

Input the DTC: P0037, P0038 or P102D.

9.

Check the DTC judgment result [E].

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



10.

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.

11.

If the test result is N/A, enter the following menus: Powertrain / Engine and ECT / Trouble Code / Pending.

12.

Read Pending DTCs.

HINT:

If a pending DTC is output, the system is malfunctioning.


13.

If the test result is INCOMPLETE or N/A and no pending DTC is output, refer to the appropriate section (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.
A112088
2.063,0.813 2.667,0.813 false 2.073,1.385 2.677,1.385 false 0.771,1.406 1.26,1.406 false 0.781,0.813 1.271,0.813 false 0.552,0.729 0.865,0.927 0.313,0.198 10 false +B 0.563,1.323 0.875,1.521 0.313,0.198 10 false E2 2.76,1.313 3.188,1.531 0.427,0.219 10 false OX1B 2.76,0.719 3.188,0.938 0.427,0.219 10 false HT1B

Disconnect the heated oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (HT1B) - 2 (+B) 20°C (68°F) 11 to 16 Ω
1 (HT1B) - 4 (E2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG


c.

Reconnect the heated oxygen sensor connector.



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)
a.
A242481
0.521,1.042 0.854,1.26 0.333,0.219 2.021,0.979 2.406,0.594 2.406,0.594 2.531,0.594 false 0.073,0.073 0.385,0.354 0.313,0.281 10 false *a 0.563,1.083 0.875,1.365 0.313,0.281 10 false C88 2.583,0.51 2.896,0.792 0.313,0.281 10 false +B
*a Front view of wire harness connector
(to Heated Oxygen Sensor)


Disconnect the heated oxygen sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C78-2 (+B) - Body ground Ignition switch ON 11 to 14 V



d.

Reconnect the heated oxygen sensor connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - INTEGRATION RELAY [MAIN])
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C78-1 (HT1B) - C97-18 (HT1B) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C78-1 (HT1B) or C97-18 (HT1B) - Body ground Always 10 kΩ or higher



d.

Reconnect the heated oxygen sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038 OR P102D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038 OR P102D)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Clear DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Start the engine.


f.

Allow the engine to idle for 1 minute or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0037, P0038 or P102D is output B




A

B

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - INTEGRATION RELAY [MAIN])
a.

Disconnect the heated oxygen sensor connector.


b.

Remove the integration relay (MAIN relay) from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C78-2 (+B) - 1J-5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C78-2 (+B) or 1J-5 - Body ground Always Below 1 Ω



d.

Reconnect the heated oxygen sensor connector.


e.

Reinstall the integration relay.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR