Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  P0137  Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)  P0138  Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)  


DESCRIPTION

HINT:

Sensor 2 refers to the sensor mounted behind the three way catalytic converter and located far from the engine assembly.


A three way catalytic converter is used in order to convert carbon monoxide, hydrocarbons and nitrogen oxide into less harmful substances. To allow the three way catalytic converter to function effectively, it is necessary to keep the air fuel ratio of the engine near the stoichiometric air fuel ratio. For the purpose of helping the ECM to deliver accurate air fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the three way catalytic converter and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with a heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The heated oxygen sensor informs the ECM that the post three way catalytic converter air fuel ratio is lean (low voltage, i.e. below 0.45 V).

Conversely, when the air fuel ratio is richer than the stoichiometric air fuel level, the oxygen concentration in the exhaust gas becomes lean. The heated oxygen sensor informs the ECM that the post three way catalytic converter air fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air fuel ratio after the three way catalytic converter is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in primary air fuel ratio control.

A208686
2.635,2.042 3.125,2.042 false 2.552,1.813 3.125,1.813 false 2.656,1.583 3.125,1.583 false 1.042,2.219 1.24,2.219 false 2.688,1.448 3.229,0.969 3.229,0.969 3.302,0.969 false 3.073,0.625 3.292,0.625 false 3.333,0.542 4.01,0.802 0.677,0.26 10 false Housing 3.344,0.896 4.604,1.313 1.26,0.417 10 false Solid Electrolyte (Zirconia Element) 3.156,1.5 4.417,1.75 1.26,0.25 10 false Platinum Electrode 3.156,1.729 3.698,1.958 0.542,0.229 10 false Heater 3.156,1.958 4.375,2.25 1.219,0.292 10 false Coating (Ceramic) 1.292,2.135 1.75,2.323 0.458,0.188 10 false Cover 1.781,2.479 2.75,2.698 0.969,0.219 10 false Exhaust Gas 1.677,0.042 2.542,0.292 0.865,0.25 10 false Atmosphere 3.958,0.208 5.021,0.479 1.063,0.271 10 false Output Voltage 5.167,0.229 6.635,0.49 1.469,0.26 10 false Ideal Air Fuel Mixture 4.719,2.25 6.75,2.521 2.031,0.271 10 false Richer - Air Fuel Ratio - Leaner

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)
·

Abnormal voltage output:

During active air fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

The heated oxygen sensor voltage does not decrease to below 0.21 V.

2.

The heated oxygen sensor voltage does not increase to higher than 0.59 V.



·

Open or short in heated oxygen sensor circuit

·

Heated oxygen sensor

·

Air fuel ratio sensor

·

Gas leak from exhaust system


Comes on DTC stored
P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)
·

Low voltage (open):

During active air fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

The heated oxygen sensor voltage output is below 0.21 V.

2.

The target air fuel ratio is rich.



·

Open in heated oxygen sensor circuit

·

Heated oxygen sensor

·

Air fuel ratio sensor

·

Gas leak from exhaust system


Comes on DTC stored
P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)
·

High voltage (short):

During active air fuel ratio control, conditions (a) and (b) are met for a certain period of time (2 trip detection logic):

1.

The heated oxygen sensor voltage output is 0.59 V or higher.

2.

The target air fuel ratio is lean.



·

Short in heated oxygen sensor circuit

·

Heated oxygen sensor

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored

WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

A301803
0.49,0.49 1.688,0.74 1.198,0.25 10 false 120 km/h (75 mph) 0.552,1.365 1.75,1.615 1.198,0.25 10 false 90 km/h (56 mph) 4.01,0.708 4.25,0.958 0.24,0.25 10 false [C] 5,3.313 5.24,3.563 0.24,0.25 10 false [D] 2.625,2.104 2.865,2.354 0.24,0.25 10 false [B] 2.021,2.427 2.26,2.677 0.24,0.25 10 false [A] 1.25,2.219 1.833,2.458 0.583,0.24 10 false Idling 0.521,2.469 1.719,2.719 1.198,0.25 10 false Ignition Switch ON 2.333,3 3.198,3.25 0.865,0.25 10 false Warming up 3.51,3.021 4.885,3.292 1.375,0.271 10 false 10 minutes or more

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

With the transmission in 5th gear or higher, drive the vehicle at 90 to 120 km/h (56 to 75 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0136, P0137 or P0138.

12.

Check the DTC judgment result.

Intelligent tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, shift the transmission to 2nd gear, and then perform steps [C] and [D] again.




HINT:

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.


CAUTION / NOTICE / HINT

HINT:

Intelligent tester only:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F sensor operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine and turn the tester on.

3.

Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.

5.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

6.

Monitor the output voltages of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the tester.



HINT:
·

The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Tester Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio sensor)
+12.5% Rich Below 3.1 V
AFS Voltage B1S1
(Air fuel ratio sensor)
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
O2S B1S2
(Heated oxygen sensor)
-12.5% Lean Below 0.4 V

NOTICE:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


A301859
0.135,0.688 0.75,0.885 0.615,0.198 10 false Case 0.844,0.635 2.906,1.021 2.063,0.385 10 false Air Fuel Ratio Sensor (Sensor 1) Output Voltage 3.427,0.625 5.573,1 2.146,0.375 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.948,0.635 7.052,1.01 1.104,0.375 10 false Main Suspected Trouble Area 6.427,2.208 6.719,2.479 0.292,0.271 10 false - 0.24,2.198 0.448,2.458 0.208,0.26 10 false 1 0.26,4.292 0.469,4.552 0.208,0.26 10 false 2 0.26,6.344 0.469,6.604 0.208,0.26 10 false 3 0.26,8.396 0.469,8.656 0.208,0.26 10 false 4 1.385,1.594 2,1.792 0.615,0.198 8 false +12.5% 1.417,1.823 2.031,2.021 0.615,0.198 8 false -12.5% 0.583,2.281 1.573,2.5 0.99,0.219 9 false Output Voltage 0.594,1.333 1.75,1.667 1.156,0.333 9 false Injection Volume 0.865,2.646 2.042,2.917 1.177,0.271 8 false Higher than 3.4 V 1.115,2.865 1.906,3.104 0.792,0.24 8 false Below 3.1 V 2.521,2.76 2.823,3.01 0.302,0.25 8 false OK 1.417,3.885 2.031,4.083 0.615,0.198 8 false -12.5% 1.396,3.656 2.01,3.854 0.615,0.198 8 false +12.5% 0.583,3.417 1.75,3.667 1.167,0.25 9 false Injection Volume 0.583,4.333 1.854,4.594 1.271,0.26 9 false Output Voltage 0.875,4.802 1.875,5.01 1,0.208 8 false Almost no reaction 2.552,4.719 2.938,5 0.385,0.281 8 false NG 1.427,5.938 2.042,6.135 0.615,0.198 8 false -12.5% 1.406,5.729 2.021,5.927 0.615,0.198 8 false +12.5% 0.583,5.469 1.677,5.667 1.094,0.198 9 false Injection Volume 0.583,6.417 1.635,6.656 1.052,0.24 9 false Output Voltage 0.865,6.76 1.917,6.917 1.052,0.156 8 false Higher than 3.4 V 1.115,6.979 1.906,7.219 0.792,0.24 8 false Below 3.1 V 2.531,6.865 2.833,7.115 0.302,0.25 8 false OK 0.583,7.5 1.583,7.708 1,0.208 9 false Injection Volume 1.427,8.01 2.042,8.208 0.615,0.198 8 false -12.5% 1.396,7.802 2.01,8 0.615,0.198 8 false +12.5% 0.583,8.438 1.635,8.667 1.052,0.229 9 false Output Voltage 0.865,8.927 1.823,9.125 0.958,0.198 8 false Almost no reaction 2.563,8.854 2.948,9.135 0.385,0.281 8 false NG 3.25,1.333 4.427,1.635 1.177,0.302 9 false Injection Volume 4.021,1.594 4.635,1.792 0.615,0.198 8 false +12.5% 4.042,1.813 4.656,2.01 0.615,0.198 8 false -12.5% 3.25,2.271 4.281,2.5 1.031,0.229 9 false Output Voltage 3.49,2.604 4.667,2.813 1.177,0.208 8 false Higher than 0.55 V 3.813,2.844 4.604,3.083 0.792,0.24 8 false Below 0.4 V 5.198,2.708 5.5,2.958 0.302,0.25 8 false OK 3.25,3.417 4.427,3.604 1.177,0.188 9 false Injection Volume 4.042,3.875 4.656,4.073 0.615,0.198 8 false -12.5% 4.01,3.667 4.625,3.865 0.615,0.198 8 false +12.5% 3.25,4.333 4.396,4.583 1.146,0.25 9 false Output Voltage 3.448,4.698 4.521,4.917 1.073,0.219 8 false Higher than 0.55 V 3.76,4.927 4.594,5.167 0.833,0.24 8 false Below 0.4 V 5.208,4.813 5.51,5.063 0.302,0.25 8 false OK 6.083,3.615 6.906,4.01 0.823,0.396 8 false Air fuel ratio sensor 6.094,4 6.854,4.573 0.76,0.573 8 false Air fuel ratio sensor heater 6.083,4.563 6.844,5.146 0.76,0.583 8 false Air fuel ratio sensor circuit 5.917,3.604 6.083,3.792 0.167,0.188 10 false - 5.917,3.99 6.083,4.177 0.167,0.188 10 false - 5.917,4.542 6.083,4.729 0.167,0.188 10 false - 4.042,5.948 4.656,6.146 0.615,0.198 8 false -12.5% 4.021,5.75 4.635,5.948 0.615,0.198 8 false +12.5% 3.25,5.469 4.354,5.729 1.104,0.26 9 false Injection Volume 3.25,6.417 4.198,6.667 0.948,0.25 9 false Output Voltage 3.5,6.865 4.552,7.052 1.052,0.188 8 false Almost no reaction 5.177,6.781 5.563,7.063 0.385,0.281 8 false NG 3.25,7.5 4.417,7.698 1.167,0.198 9 false Injection Volume 4.031,8 4.646,8.198 0.615,0.198 8 false -12.5% 4.01,7.813 4.625,8.01 0.615,0.198 8 false +12.5% 3.479,8.938 4.521,9.104 1.042,0.167 8 false Almost no reaction 5.156,8.854 5.542,9.135 0.385,0.281 8 false NG 3.26,8.417 4.333,8.667 1.073,0.25 9 false Output Voltage 6.083,5.438 6.927,5.75 0.844,0.313 8 false Heated oxygen sensor 6.073,5.958 6.896,6.333 0.823,0.375 8 false Heated oxygen sensor heater 6.073,6.646 6.917,7.25 0.844,0.604 8 false Heated oxygen sensor circuit 5.917,5.948 6.083,6.135 0.167,0.188 10 false - 5.917,5.417 6.083,5.604 0.167,0.188 10 false - 5.917,6.615 6.083,6.802 0.167,0.188 10 false - 6.083,7.531 6.948,7.906 0.865,0.375 8 false Fuel injector assembly 6.083,7.917 6.833,8.167 0.75,0.25 8 false Fuel pressure 6.094,8.177 6.917,9.281 0.823,1.104 8 false Gas leak from exhaust system (air-fuel ratio extremely rich or lean) 5.917,7.521 6.083,7.708 0.167,0.188 10 false - 5.917,7.906 6.083,8.094 0.167,0.188 10 false - 5.917,8.156 6.083,8.344 0.167,0.188 10 false -

·

Following the Control the Injection Volume for air fuel ratio sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensor sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / A/F Control System / AFS Voltage B1S1 and O2S B1S2.


HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.READ OUTPUT DTC (DTC P0136, P0137 OR P0138)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read DTCs.

Result:
Result Proceed to
DTC P0138 is output A
DTC P0137 is output B
DTC P0136 is output C
P0136, P0137 or P0138 and other DTCs are output D




A

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)

B

10.CHECK FOR EXHAUST GAS LEAK

C

16.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)

D

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / O2S B1S2.

Powertrain > Engine and ECT > Data List
Tester Display
O2S B1S2
50003 234 44

e.

Allow the engine to idle.


f.

Read the heated oxygen sensor output voltage while idling.

Result:
Result Proceed to
Higher than 1.0 V A
Below 1.0 V B




A

3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)

B

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)
a.

Inspect the heated oxygen sensor connector

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION


b.

Reconnect the heated oxygen sensor connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

NG

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C97-18 (HT1B) - C97-13 (OX1B) Always 10 kΩ or higher



c.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - HEATED OXYGEN SENSOR)

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
O2S B1S2
50004 234 2 35,44

f.

Change the fuel injection volume using the tester and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.


HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the heated oxygen sensor is displayed as O2S B1S2 on the intelligent tester.



Result:
Tester Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1
(Air fuel ratio sensor)
Alternates between higher than and below 3.3 V OK
AFS Voltage B1S1
(Air fuel ratio sensor)
Remains at higher than 3.3 V NG
AFS Voltage B1S1
(Air fuel ratio sensor)
Remains at below 3.3 V


HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either below or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606
5.885,2.458 6.365,1.396 false 5.542,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.292,1.771 4.094,1.698 false 3.573,2.625 3.188,2.938 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 3.3 V 2.656,0.292 3.208,0.521 0.552,0.229 10 +12.5% 4.031,1.135 4.573,1.417 0.542,0.281 10 -12.5% 1.656,2.854 1.906,3.052 0.25,0.198 10 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 0 V 3.073,1.146 3.833,1.344 0.76,0.198 10 Malfunction 5.854,2.615 6.646,2.885 0.792,0.271 10 Malfunction 4.76,0.125 5.865,0.354 1.104,0.229 10 Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 Heated Oxygen Sensor Output 6.406,1.125 6.958,1.813 0.552,0.688 10 Air Fuel Ratio Sensor Output 4.344,1.729 4.865,1.958 0.521,0.229 10 Normal


OK

6.CHECK AIR FUEL RATIO SENSOR

NG

7.REPLACE AIR FUEL RATIO SENSOR
6.CHECK AIR FUEL RATIO SENSOR
HINT:

This air fuel ratio sensor test is used to check the air fuel ratio sensor current during the fuel-cut operation. When the sensor is normal, the sensor current is below 3 mA in this test.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC / Clear.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Clear DTCs.


f.

Drive the vehicle according to the driving pattern listed below:

i.

Warm up the engine.


ii.

Drive the vehicle at 60 km/h (37 mph) or more for 10 minutes or more.


iii.

Stop the vehicle.


iv.

Accelerate the vehicle to 60 km/h (37 mph) or more and then decelerate for 5 seconds or more. Repeat this process at least 3 times.

A152792
1.24,2.51 2.635,2.719 1.396,0.208 10 false 10 minutes or more 2.865,2.51 4.344,2.719 1.479,0.208 10 false 5 seconds or more 4.24,2.51 5.583,2.74 1.344,0.229 10 false 5 seconds or more 5.625,2.51 6.99,2.729 1.365,0.219 10 false 5 seconds or more 0.156,0.083 1.781,0.385 1.625,0.302 12 false Driving Pattern: 0.302,1.229 0.948,1.635 0.646,0.406 10 false 60 km/h (40 mph) 0.344,2.052 0.865,2.469 0.521,0.417 10 false 0 km/h (0 mph)



g.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / AFS Current B1S1.

Powertrain > Engine and ECT > Data List
Tester Display
AFS Current B1S1
50003 234 39

h.

Read the value of the air fuel ratio sensor current while the fuel-cut operation is being performed.

Standard current:

Below 3.0 mA


HINT:
·

To measure the air fuel ratio sensor current precisely, perform the fuel-cut operation as long as possible.

·

If it is difficult to measure the air fuel ratio sensor current, use the snapshot function of the intelligent tester.




Result:
Result Proceed to
Outside standard range B
Within standard range A



A

13.REPLACE HEATED OXYGEN SENSOR

B

7.REPLACE AIR FUEL RATIO SENSOR
7.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

8.PERFORM CONFIRMATION DRIVING PATTERN
8.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Refer to Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

e.

Input DTCs: P0136, P0137 and P0138.


f.

Check that DTC monitor is NORMAL. If DTC monitor is INCOMPLETE, perform the driving pattern by accelerating the vehicle to a higher speed and using the second gear to decelerate the vehicle.

Result:
Result Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(DTC P0136, P0137 or P0138 output)
B




A

END

B

10.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leakage.

OK:

No gas leakage.



Result:
Proceed to
OK
NG



OK

11.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT

11.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

12.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C88-1 (HT1B) - C97-18 (HT1B) Always Below 1 Ω
C88-3 (OX1B) - C97-13 (OX1B) Always Below 1 Ω
C88-4 (E2) - C97-14 (EX1B) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C88-1 (HT1B) or C97-18 (HT1B) - Body ground Always Below 1 Ω
C88-3 (OX1B) or C97-13 (OX1B) - Body ground Always Below 1 Ω
C88-4 (E2) or C97-14 (EX1B) - Body ground Always Below 1 Ω



d.

Reconnect the heated oxygen sensor connector.


e.

Reconnect the ECM connector.

A303366
0.135,0.125 2.802,0.375 2.667,0.25 10 false Reference (System Diagram of Sensor 2): 0.167,0.667 0.656,1.052 0.49,0.385 10 false from Battery 1.302,0.854 1.573,1.042 0.271,0.188 10 false EFI 2.177,1.885 2.563,2.094 0.385,0.208 10 false MAIN 0.792,2.99 1.302,3.198 0.51,0.208 10 false Ground 3.698,0.594 3.927,0.781 0.229,0.188 10 false +B 3.698,1.271 3.927,1.458 0.229,0.188 10 false E2 4.75,0.604 5.229,0.802 0.479,0.198 10 false HT1B 4.75,1.271 5.229,1.469 0.479,0.198 10 false OX1B 5.333,0.604 5.813,0.802 0.479,0.198 10 false HT1B 5.323,1.271 5.802,1.469 0.479,0.198 10 false OX1B 4.083,0.896 4.573,1.135 0.49,0.24 10 false Heater 4.073,1.583 4.563,1.813 0.49,0.229 10 false Sensor 3.688,1.99 5.177,2.229 1.49,0.24 10 false Heated Oxygen Sensor 5.292,2.313 5.771,2.51 0.479,0.198 10 false EX1B 5.313,2.656 5.792,2.854 0.479,0.198 10 false MREL 6.01,3.156 6.49,3.354 0.479,0.198 10 false ECM


Result:
Proceed to
OK
NG



OK

13.REPLACE HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - HEATED OXYGEN SENSOR)

13.REPLACE HEATED OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

14.PERFORM CONFIRMATION DRIVING PATTERN
14.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Refer to Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

e.

Input DTCs: P0136, P0137 and P0138.


f.

Check that DTC monitor is NORMAL. If DTC monitor is INCOMPLETE, perform the driving pattern by accelerating the vehicle to a higher speed and using second gear to decelerate the vehicle.

Result:
Result Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(DTC P0136, P0137 or P0138 output)
B




A

END

B

16.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Start the engine.


e.

Enter the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
O2S B1S2
50004 234 2 35,44

f.

Change the fuel injection volume using the tester, and monitor the voltage output of the heated oxygen sensor displayed on the tester.

HINT:
·

Change the fuel injection volume within the range of -12.5% and +12.5%.

·

The heated oxygen sensor is displayed as O2S B1S2 on the intelligent tester.




Result:
Tester Display (Sensor) Voltage Variation Proceed to
O2S B1S2
(Heated oxygen sensor)
Alternates between 0.5 V or more and less than 0.4 V OK
Remains at 0.5 V or more NG
Remains at less than 0.4 V


HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the heated oxygen sensor (sensor 2) voltage remains at either 0.5 V or more or less than 0.4 V despite the heated oxygen sensor indicating a normal reaction, the heated oxygen sensor (sensor 2) is malfunctioning.



OK

17.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

10.CHECK FOR EXHAUST GAS LEAK
17.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
AFS Voltage B1S1
O2S B1S2
50004 234 2 35,44

f.

Change the fuel injection volume using the tester and monitor the voltage output of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.


HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor is displayed as AFS Voltage B1S1, and the heated oxygen sensor is displayed as O2S B1S2 on the intelligent tester.



Result:
Tester Display (Sensor) Voltage Variation Proceed to
AFS Voltage B1S1
(Air fuel ratio sensor)
Alternates between higher than and below 3.3 V OK
AFS Voltage B1S1
(Air fuel ratio sensor)
Remains at higher than 3.3 V NG
AFS Voltage B1S1
(Air fuel ratio sensor)
Remains at below 3.3 V


HINT:

A normal heated oxygen sensor voltage (O2S B1S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either below or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606
5.885,2.458 6.365,1.396 false 5.542,2.271 6.365,1.396 false 5.708,1.667 6.365,1.396 false 5.563,2.448 5.844,2.667 false 3.021,1.26 2.865,1.677 false 4.292,1.771 4.094,1.698 false 3.573,2.625 3.188,2.938 false 1.958,1.99 2.125,1.99 false 1.958,2.948 2.156,2.948 false 1.531,1.896 1.906,2.052 0.375,0.156 10 3.3 V 2.656,0.292 3.208,0.521 0.552,0.229 10 +12.5% 4.031,1.135 4.573,1.417 0.542,0.281 10 -12.5% 1.656,2.854 1.906,3.052 0.25,0.198 10 1 V 1.667,3.385 1.906,3.583 0.24,0.198 10 0 V 3.073,1.146 3.833,1.344 0.76,0.198 10 Malfunction 5.854,2.615 6.646,2.885 0.792,0.271 10 Malfunction 4.76,0.125 5.865,0.354 1.104,0.229 10 Injection Volume 3.635,2.51 5.563,2.729 1.927,0.219 10 Heated Oxygen Sensor Output 6.406,1.125 6.958,1.813 0.552,0.688 10 Air Fuel Ratio Sensor Output 4.344,1.729 4.865,1.958 0.521,0.229 10 Normal


OK

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO AND REPAIR CAUSE (FUEL INJECTOR, FUEL PRESSURE, GAS LEAK FROM SYSTEM, ETC.)

NG

7.REPLACE AIR FUEL RATIO SENSOR