| Malfunction Condition | Main Trouble Area | Related Trouble Area |
|---|---|---|
·
Knocking and abnormal sound due to extremely rich combustion ·
Abnormal sound due to friction between parts |
(a) Injector assembly malfunctions
·
Injector sliding malfunction ·
Injector stuck closed ·
Injector stuck open ·
Deposits in injector ·
Injector circuit malfunction (b) Abnormal common rail pressure ·
Suction control valve (fuel supply pump assembly) ·
Fuel pulsation sound ·
Air in fuel (c) Friction between parts (d) Compression pressure |
·
Injector compensation codes ·
Fuel leakage ·
Intake air system leakage ·
Intake air system blockage ·
EGR system ·
Throttle valve system ·
Fuel pressure sensor (common rail assembly) ·
Manifold absolute pressure sensor ·
Mass air flow meter ·
Atmospheric pressure sensor (built into ECM) ·
Vehicle modifications ·
Low quality fuel ·
Lack of fuel ·
ECM |
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors of the malfunction.
Check that the vehicle has not been modified in any way prior to the vehicle inspection.
This troubleshooting procedure checks for knocking and rattling.
Knocking is most likely to occur while the engine is idling.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION).
Find the source of the abnormal sound using a mechanic's stethoscope.
| Result | Proceed to |
|---|---|
| Combustion noise from engine | A |
| Noise from specific part | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No output | A |
| Engine related DTCs | B |
A
B
Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.
Check the injector compensation code.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION
Compensation codes of the installed injector assemblies are the same as the compensation codes registered in the ECM.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
Take a snapshot of the following Data List items.
A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
Graphs like the ones shown below can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.
Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.
| Proceed to |
|---|
| NEXT |
NEXT
Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken when the engine was idling and at 4000 rpm with no load.
| Result | Proceed to |
|---|---|
| Injection Feedback Val for at least one cylinder is more than +3 mm3/st | A |
| Injection Volume is 10 mm3/st or less at 4000 rpm | B |
| Except above | C |
When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (- 3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.
A
B
C
Use this Active Test to help determine whether a cylinder has compression loss or not.
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
| Active Test Display |
|---|
| Check the Cylinder Compression |
| Data List Display |
|---|
| Engine Speed of Cyl #1 |
| Engine Speed of Cyl #2 |
| Engine Speed of Cyl #3 |
| Engine Speed of Cyl #4 |
Check the engine speed during the Active Test.
| Result | Proceed to |
|---|---|
| Except below | A |
| The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other. | B |
When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.
A
B
Check the cylinder compression pressure.
Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION
When compression is low, there may be cracks in the piston or the injector may be installed improperly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the injector assembly of the malfunctioning cylinder.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/o Glow Plug Controller)>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Clean the interior of the fuel filter case.
If the fuel filter is obviously dirty or clogged, replace the fuel filter.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM(w/o Glow Plug Controller)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
RegisRegister the injector compensation codes.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION
Perform the fuel injector pilot quantity learning.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Check whether the knocking has been successfully repaired.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel injectors.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/o Glow Plug Controller)>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Check Fuel Press and Target Common Rail Pressure in the snapshot taken when the engine was warmed up and idling.
Fuel Press is within +/-5000 kPa of Target Common Rail Pressure.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the temperature when knocking trouble occurs.
| Result | Proceed to |
|---|---|
| Knocking occurs only in cold engine | A |
| Knocking occurs both in cold and warmed up engine | B |
A
B
Inspect the glow plug.
Click hereEngine / Hybrid System>1KD-FTV STARTING>GLOW PLUG(w/o Glow Plug Controller)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that the engine is cold so that the snapshot can be taken under the correct conditions.
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
Take a snapshot of the following Data List items.
A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.
Graphs like the ones shown below can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.
| Proceed to |
|---|
| NEXT |
NEXT
Check Injection Feedback Val #1 to #4 in the snapshot taken when the engine was idling.
| Result | Proceed to |
|---|---|
| Injection Feedback Val for at least one cylinder is more than +3 mm3/st | A |
| Except above | B |
When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (- 3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.
| Tester Display |
|---|
| Atmosphere Pressure |
| MAP |
Compare MAP to Atmosphere Pressure when the ignition switch is ON (do not start the engine).
Difference between MAP and Atmosphere Pressure is less than 8 kPa.
If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
| Result | Proceed to |
|---|---|
| MAP and Atmosphere Pressure have same value | A |
| MAP is different from actual atmospheric pressure | B |
| Atmosphere Pressure is different from actual atmospheric pressure | C |
A
B
C
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SUPPLY PUMP(w/o Glow Plug Controller)>REMOVAL
If the common rail pressure becomes too high when transitioning due to problems with SCV operation, knocking noise worsens.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system .
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SYSTEM(w/o Glow Plug Controller)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Perform fuel supply pump initialization.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Check whether the knocking has been successfully repaired by starting the engine.
| Proceed to |
|---|
| NEXT |
NEXT