Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009608 CRUISE CONTROL _0052446 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

This circuit sends a signal to the ECM depending on the cruise control main switch condition. The battery supplies positive (+) battery voltage to the cruise control main switch. Terminal 21 (CCS)*1 or 14 (CCS)*2 of the ECM receives the voltage which varies according to the switch condition.

*1: except i-ART

*2: for i-ART

WIRING DIAGRAM

E200577
6.156,1.271 7.156,1.49 1,0.219 10 false G39*1, G157*2 6.406,0.604 6.76,0.792 0.354,0.188 10 false CCS 6.01,0.396 6.344,0.583 0.333,0.188 10 false 21*1 6.01,0.521 6.354,0.719 0.344,0.198 10 false 14*2 3.875,0.5 4.063,0.698 0.188,0.198 10 false 3 3.885,1.552 4.073,1.76 0.188,0.208 10 false 1 6.156,1.396 6.49,1.604 0.333,0.208 10 false ECM 4.979,2.125 5.958,2.552 0.979,0.427 10 false Spiral Cable Sub-assembly 5.604,0.604 5.927,0.792 0.323,0.188 10 false G12 5.604,1.656 5.938,1.854 0.333,0.198 10 false G12 4.958,1.667 5.115,1.854 0.156,0.188 10 false B 4.958,0.604 5.115,0.781 0.156,0.177 10 false B 5.698,1.479 5.833,1.667 0.135,0.188 10 false 2 5.698,0.417 5.813,0.615 0.115,0.198 10 false 1 4.969,1.479 5.083,1.688 0.115,0.208 10 false 4 4.958,0.427 5.063,0.625 0.104,0.198 10 false 3 5.219,0.51 5.552,0.719 0.333,0.208 10 false CCS 5.219,1.563 5.542,1.781 0.323,0.219 10 false ECC 3.5,0.521 3.813,0.729 0.313,0.208 10 false CCS 3.5,1.573 3.823,1.771 0.323,0.198 10 false ECC 3.948,1.948 4.854,2.313 0.906,0.365 10 false Cruise Control Switch Wire 1.219,2.302 2.969,2.51 1.75,0.208 10 false Cruise Control Main Switch 3.198,1.125 3.781,1.323 0.583,0.198 10 false ON-OFF 1.646,1.125 2.031,1.333 0.385,0.208 10 false -SET 2.469,1.125 2.896,1.354 0.427,0.229 10 false +RES 0.833,1.125 1.458,1.333 0.625,0.208 10 false CANCEL 1.219,2.156 1.396,2.323 0.177,0.167 10 false A 0.073,2.271 1.156,2.479 1.083,0.208 10 false *1: except i-ART 0.073,2.521 0.958,2.75 0.885,0.229 10 false *2: for i-ART

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH)
a.

Using the intelligent tester, read the Data List.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Cruise Control:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
CCS Main SW M-CPU Cruise control main switch signal (Main CPU) / ON or OFF ON: Cruise control main switch (Main CPU) on
OFF: Cruise control main switch (Main CPU) off
-
Cancel Switch CANCEL switch signal / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch SET / COAST switch signal / ON or OFF ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch RES / ACC switch signal / ON or OFF ON: +RES switch on
OFF: +RES switch off
-


OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Remove the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL

B215369
0.708,2.76 0.927,2.438 false 1.448,2.74 1.302,2.438 false 0.521,2.802 0.979,3 0.458,0.198 10 CCS 1.365,2.792 1.823,2.99 0.458,0.198 10 ECC 3.833,2.448 4.75,2.646 0.917,0.198 10 ON-OFF 2.615,2.094 3.073,2.292 0.458,0.198 10 ECC 2.615,2.74 3.104,2.917 0.49,0.177 10 CCS 4.531,2.438 5.115,2.719 0.583,0.281 10 +RES 5.281,2.427 5.896,2.625 0.615,0.198 10 -SET 5.958,2.417 6.875,2.615 0.917,0.198 10 CANCEL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (CCS) - 1 (ECC) Cruise control main switch on Below 2.5 Ω
Cruise control main switch off 1 MΩ or higher
+RES switch held on 235 to 245 Ω
-SET switch held on 617 to 643 Ω
CANCEL switch held on 1509 to 1571 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT CRUISE CONTROL SWITCH WIRE

NG

3.INSPECT CRUISE CONTROL SWITCH WIRE
a.
E178683
1,0.104 1.281,0.302 0.281,0.198 1.052,1.646 1.313,1.844 0.26,0.198 0.885,1.375 1.063,1.104 true 1.302,1.115 1.469,1.365 true 0.833,3.052 0.99,2.646 true 1.563,3.063 1.427,2.677 true 0.76,1.406 1.219,1.604 0.458,0.198 10 CCS 1.458,3.094 1.917,3.292 0.458,0.198 10 CCS 1.375,1.396 1.833,1.594 0.458,0.198 10 ECC 0.719,3.104 1.177,3.302 0.458,0.198 10 ECC 1.146,1.677 1.302,1.875 0.156,0.198 10 A 1.094,0.135 1.25,0.333 0.156,0.198 10 B

Remove the cruise control switch wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 (CCS) - B-3 (CCS) Always Below 1 Ω
A-1 (ECC) - B-4 (ECC)



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.
E176804
2.344,0.51 2.615,0.802 0.271,0.292 1.052,3.354 1.323,3.563 0.271,0.208 1.823,1.104 1.948,0.875 true 0.948,4.229 1.083,3.917 true 2.083,0.885 2.25,1.073 true 1.563,4.26 1.167,3.917 true 1.656,1.115 2.115,1.313 0.458,0.198 10 ECC 1.438,4.26 1.896,4.458 0.458,0.198 10 ECC 2.146,1.115 2.604,1.313 0.458,0.198 10 CCS 0.813,4.26 1.271,4.458 0.458,0.198 10 CCS 2.427,0.573 2.635,0.771 0.208,0.198 10 B 1.135,3.385 1.302,3.594 0.167,0.208 10 A

Remove the spiral cable.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

If there are any defects as follows, replace the spiral cable with a new one: scratches, cracks, dents or chips on the connector or spiral cable.


c.

Check the spiral cable.

i.

Set the spiral cable to the center position.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION


ii.

Rotate the spiral cable 2.5 times clockwise and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise and measure the resistance according to the value(s) in the table below.

NOTICE:

As the spiral cable may break, do not rotate the spiral cable more than the specified amount.


Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (CCS) - B-3 (CCS) Always Below 1 Ω
A-2 (ECC) - B-4 (ECC)



iii.

Set the spiral cable to the center position and rotate the spiral cable 2.5 times clockwise. Then, while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (CCS) - B-3 (CCS) Always Below 1 Ω
A-2 (ECC) - B-4 (ECC)




Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)

*1: except i-ART

*2: for i-ART


a.

Disconnect the G12 spiral cable connector.


b.

Disconnect the G39*1 or G157*2 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except i-ART
Tester Connection Condition Specified Condition
G12-1 (CCS) - G39-21 (CCS) Always Below 1 Ω
G12-2 (ECC) - Body ground
G12-1 (CCS) - Body ground Always 10 kΩ or higher

for i-ART
Tester Connection Condition Specified Condition
G12-1 (CCS) - G157-14 (CCS) Always Below 1 Ω
G12-2 (ECC) - Body ground
G12-1 (CCS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR