Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) J

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A206916
4.375,1.25 6.219,1.594 1.844,0.344 10 false 5 V Constant Voltage Circuit 5.354,2.094 6.365,2.438 1.01,0.344 10 false Microprocessor 1.729,1.115 2.802,1.365 1.073,0.25 10 false from EFI Fuse 1.573,1.448 2.771,1.708 1.198,0.26 10 false from MAIN Relay 2.906,1.031 3.302,1.219 0.396,0.188 10 false BATT 0.354,2.229 2.615,2.802 2.26,0.573 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (sensors which have ICs) 0.365,2.969 2.625,3.438 2.26,0.469 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.063,3.125 4.323,3.333 0.26,0.208 10 false R 3,1.375 3.281,1.573 0.281,0.198 10 false +B 3.177,2.25 3.542,2.479 0.365,0.229 10 false VC 4.885,3.375 5.333,3.604 0.448,0.229 10 false ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A276478
0.479,7.5 2.26,7.844 1.781,0.344 10 false Fuel Pressure Sensor 0.469,3.531 2.75,3.833 2.281,0.302 10 false Accelerator Pedal Position Sensor 1.708,1.521 2.083,1.771 0.375,0.25 10 false EPA 1.615,2.615 2.042,2.854 0.427,0.24 10 false EPA2 1.635,2.26 2.052,2.49 0.417,0.229 10 false VPA2 1.615,1.896 2.052,2.115 0.438,0.219 10 false VCPA 1.698,1.146 2.063,1.385 0.365,0.24 10 false VPA 1.615,2.99 2.063,3.219 0.448,0.229 10 false VCP2 2.115,1.052 2.271,1.229 0.156,0.177 10 false 6 2.115,1.427 2.271,1.604 0.156,0.177 10 false 5 2.115,1.802 2.271,1.979 0.156,0.177 10 false 4 2.115,2.167 2.271,2.344 0.156,0.177 10 false 3 2.115,2.542 2.271,2.719 0.156,0.177 10 false 2 2.104,2.906 2.26,3.083 0.156,0.177 10 false 1 5.24,2.094 5.396,2.271 0.156,0.177 10 false 1 5.229,0.958 5.385,1.135 0.156,0.177 10 false 2 5.24,1.344 5.396,1.521 0.156,0.177 10 false 5 5.24,1.719 5.396,1.896 0.156,0.177 10 false 6 5.24,2.458 5.396,2.635 0.156,0.177 10 false 3 5.24,2.833 5.396,3.01 0.156,0.177 10 false 4 5.573,1.51 6.01,1.76 0.438,0.25 10 false EPA 5.563,2.615 6.021,2.792 0.458,0.177 10 false EPA2 5.563,2.26 6.021,2.438 0.458,0.177 10 false VPA2 5.563,1.885 6.052,2.083 0.49,0.198 10 false VCPA 5.563,1.135 5.969,1.385 0.406,0.25 10 false VPA 5.563,3 6.073,3.219 0.51,0.219 10 false VCP2 5.115,2.26 5.521,2.438 0.406,0.177 10 false G149 5.115,1.146 5.521,1.323 0.406,0.177 10 false G149 5.115,3.01 5.521,3.188 0.406,0.177 10 false G148 5.115,2.635 5.521,2.813 0.406,0.177 10 false G148 5.115,1.896 5.521,2.073 0.406,0.177 10 false G148 5.115,1.521 5.521,1.698 0.406,0.177 10 false G148 1.792,6.938 2.063,7.125 0.271,0.188 10 false E2 1.719,5.771 2.083,5.979 0.365,0.208 10 false E2S 1.719,5.365 2.125,5.552 0.406,0.188 10 false PR2 1.771,6.156 2.094,6.344 0.323,0.188 10 false VC 1.771,6.552 2.135,6.75 0.365,0.198 10 false PR 1.698,4.979 2.104,5.188 0.406,0.208 10 false VCS 2.177,6.052 2.333,6.229 0.156,0.177 10 false 6 2.156,6.448 2.313,6.625 0.156,0.177 10 false 5 2.156,6.854 2.313,7.031 0.156,0.177 10 false 4 2.177,5.667 2.333,5.844 0.156,0.177 10 false 3 2.177,5.281 2.333,5.458 0.156,0.177 10 false 2 2.156,4.885 2.313,5.063 0.156,0.177 10 false 1 5.563,6.927 5.938,7.146 0.375,0.219 10 false E2 5.563,5.75 6,5.979 0.438,0.229 10 false E2S 5.552,5.365 6.01,5.594 0.458,0.229 10 false PCR2 5.563,6.135 5.917,6.313 0.354,0.177 10 false VC 5.552,6.531 6.052,6.76 0.5,0.229 10 false PCR1 5.563,4.979 5.958,5.188 0.396,0.208 10 false VCS 5.125,4.979 5.521,5.156 0.396,0.177 10 false C113 5.125,5.771 5.521,5.948 0.396,0.177 10 false C113 5.125,5.375 5.521,5.552 0.396,0.177 10 false C113 5.125,6.156 5.5,6.333 0.375,0.177 10 false C114 5.125,6.938 5.5,7.115 0.375,0.177 10 false C114 5.125,6.552 5.521,6.729 0.396,0.177 10 false C113 5.208,5.99 5.479,6.167 0.271,0.177 10 false 13 5.208,6.385 5.542,6.583 0.333,0.198 10 false 16 5.208,6.771 5.438,6.969 0.229,0.198 10 false 14 5.26,5.594 5.417,5.771 0.156,0.177 10 false 8 5.26,5.198 5.417,5.375 0.156,0.177 10 false 2 5.208,4.802 5.427,4.979 0.219,0.177 10 false 13 5.917,8.313 6.323,8.552 0.406,0.24 10 false ECM 3.146,8.448 3.427,8.646 0.281,0.198 10 false A 4.156,8.448 4.448,8.656 0.292,0.208 10 false B 0.448,3.365 0.76,3.563 0.313,0.198 10 false G6 0.469,7.313 0.927,7.51 0.458,0.198 10 false C16

A276479
0.323,8.01 2.729,8.281 2.406,0.271 10 false Electric EGR Control Valve Assembly 1.781,3.479 2.042,3.635 0.26,0.156 10 false VC 1.708,3.917 2.125,4.115 0.417,0.198 10 false PEX 1.802,4.333 2.125,4.542 0.323,0.208 10 false E2 1.76,5.583 2.104,5.875 0.344,0.292 10 false VC 1.688,6.042 2.125,6.281 0.438,0.24 10 false VTA 1.781,6.521 2.073,6.708 0.292,0.188 10 false E2 1.75,7 2.125,7.24 0.375,0.24 10 false M+ 1.771,7.448 2.104,7.656 0.333,0.208 10 false M- 5.573,3.896 6,4.083 0.427,0.188 10 false PEX 5.563,6.052 6.135,6.281 0.573,0.229 10 false EGRA 5.563,7 6.063,7.333 0.5,0.333 10 false EGM+ 5.563,7.458 6.073,7.719 0.51,0.26 10 false EGM- 5.135,3.906 5.531,4.063 0.396,0.156 10 false C114 5.135,6.052 5.542,6.208 0.406,0.156 10 false C113 5.135,6.99 5.542,7.146 0.406,0.156 10 false C112 5.135,7.469 5.542,7.625 0.406,0.156 10 false C112 2.146,3.375 2.281,3.552 0.135,0.177 10 false 3 2.146,3.802 2.281,3.979 0.135,0.177 10 false 2 2.146,4.219 2.281,4.396 0.135,0.177 10 false 1 2.115,5.479 2.25,5.656 0.135,0.177 10 false 3 2.135,5.948 2.323,6.135 0.188,0.188 10 false 2 2.125,6.417 2.323,6.594 0.198,0.177 10 false 1 2.135,6.885 2.313,7.073 0.177,0.188 10 false 4 2.135,7.354 2.365,7.531 0.229,0.177 10 false 5 5.25,3.719 5.458,3.896 0.208,0.177 10 false 7 5.25,5.875 5.448,6.052 0.198,0.177 10 false 1 5.26,6.813 5.469,7 0.208,0.188 10 false 6 5.271,7.292 5.417,7.469 0.146,0.177 10 false 7 5.906,8.458 6.396,8.677 0.49,0.219 10 false ECM 0.438,2.656 2.417,3.042 1.979,0.385 10 false Diesel Throttle Body Assembly 2.135,1.104 2.292,1.281 0.156,0.177 10 false 1 2.135,1.531 2.292,1.708 0.156,0.177 10 false 3 2.135,1.958 2.292,2.135 0.156,0.177 10 false 2 5.135,1.656 5.5,1.833 0.365,0.177 10 false C114 5.26,1.469 5.417,1.646 0.156,0.177 10 false 3 1.729,1.646 2.073,1.823 0.344,0.177 10 false VTA 1.792,1.219 2.104,1.396 0.313,0.177 10 false VC 1.875,2.073 2.104,2.281 0.229,0.208 10 false E 5.563,1.646 5.979,1.844 0.417,0.198 10 false VLU 2.938,0.323 3.104,0.542 0.167,0.219 10 false A 3.938,0.313 4.104,0.531 0.167,0.219 10 false B 2.938,8.26 3.104,8.479 0.167,0.219 10 false A 3.938,8.25 4.104,8.469 0.167,0.219 10 false B 0.438,2.49 0.75,2.688 0.313,0.198 10 false C9 0.302,4.76 0.844,4.948 0.542,0.188 10 false C125 0.313,4.917 2.24,5.25 1.927,0.333 10 false Differential Pressure Sensor 0.313,7.854 0.927,8.031 0.615,0.177 10 false C120

A276480
0.458,2.146 2.792,2.396 2.333,0.25 10 false Manifold Absolute Pressure Sensor 0.448,4.385 2.51,4.656 2.063,0.271 10 false Nozzle Vane Position Sensor 2.135,0.594 2.313,0.781 0.177,0.188 10 false 3 2.135,1.021 2.292,1.198 0.156,0.177 10 false 2 2.135,1.458 2.385,1.625 0.25,0.167 10 false 1 2.115,2.833 2.271,3.01 0.156,0.177 10 false 3 2.115,3.688 2.271,3.865 0.156,0.177 10 false 2 2.115,3.271 2.271,3.448 0.156,0.177 10 false 1 1.802,0.719 2.073,0.917 0.271,0.198 10 false VC 1.75,1.135 2.104,1.333 0.354,0.198 10 false PIM 1.875,1.563 2.094,1.75 0.219,0.188 10 false E 5.563,1.146 6.083,1.458 0.521,0.313 10 false PIM 5.146,3.802 5.563,3.979 0.417,0.177 10 false C114 5.146,2.948 5.563,3.125 0.417,0.177 10 false C114 5.146,3.375 5.563,3.552 0.417,0.177 10 false C114 5.146,1.146 5.563,1.323 0.417,0.177 10 false C114 5.271,0.958 5.5,1.125 0.229,0.167 10 false 5 5.229,2.76 5.469,2.948 0.24,0.188 10 false 11 5.24,3.625 5.469,3.802 0.229,0.177 10 false 10 5.271,3.208 5.427,3.385 0.156,0.177 10 false 6 5.563,2.938 6.063,3.146 0.5,0.208 10 false VNVC 5.563,3.365 5.979,3.604 0.417,0.24 10 false VNA 5.563,3.792 6.052,4.01 0.49,0.219 10 false VNE2 1.604,2.938 2.083,3.198 0.479,0.26 10 false VNVC 1.615,3.375 2.073,3.635 0.458,0.26 10 false VTA1 1.615,3.802 2.063,4.063 0.448,0.26 10 false VNE2 5.927,4.427 6.333,4.667 0.406,0.24 10 false ECM 3.063,0.24 3.271,0.427 0.208,0.188 10 false A 4.073,0.24 4.344,0.438 0.271,0.198 10 false B 0.448,1.969 1.271,2.177 0.823,0.208 10 false C20 0.438,4.219 1.063,4.438 0.625,0.219 10 false C40

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B




A

END

B

2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and tester on.


c.

Check the communication between the tester and ECM.

Result:
Result Proceed to
Communication is possible A
Communication is not possible B




A

B

3.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
3.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the accelerator pedal position sensor connector.



A

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

B

4.CHECK MIL (THROTTLE POSITION SENSOR)
4.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the throttle position sensor connector.



A

B

5.CHECK MIL (FUEL PRESSURE SENSOR)
5.CHECK MIL (FUEL PRESSURE SENSOR)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the fuel pressure sensor connector.



A

B

6.CHECK MIL (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
6.CHECK MIL (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the electric EGR control valve assembly connector.



A

REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY

B

7.CHECK MIL (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY)
7.CHECK MIL (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY)
a.

Disconnect the differential pressure sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the differential pressure sensor assembly connector.



A

REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

B

8.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
8.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the manifold absolute pressure sensor connector.



A

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

B

9.CHECK MIL (NOZZLE VANE POSITION SENSOR)
9.CHECK MIL (NOZZLE VANE POSITION SENSOR)
a.

Disconnect the nozzle vane position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the nozzle vane position sensor connector.



A

B

10.CHECK HARNESS AND CONNECTOR
10.CHECK HARNESS AND CONNECTOR
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the throttle position sensor connector.


c.

Disconnect the fuel pressure sensor connector.


d.

Disconnect the electric EGR control valve assembly connector.


e.

Disconnect the differential pressure sensor assembly connector.


f.

Disconnect the nozzle vane position sensor connector.


g.

Disconnect the manifold absolute pressure sensor connector.


h.

Disconnect the ECM connectors.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G148-6 (VCPA) - Body ground Always 10 kΩ or higher
G148-4 (VCP2) - Body ground Always 10 kΩ or higher
C114-13 (VC) - Body ground Always 10 kΩ or higher
C113-13 (VCS) - Body ground Always 10 kΩ or higher
C114-11 (VNVC) - Body ground Always 10 kΩ or higher



j.

Reconnect the accelerator pedal position sensor connector.


k.

Reconnect the throttle position sensor connector.


l.

Reconnect the fuel pressure sensor connector.


m.

Reconnect the electric EGR control valve assembly connector.


n.

Reconnect the differential pressure sensor assembly connector.


o.

Reconnect the nozzle vane position sensor connector.


p.

Reconnect the manifold absolute pressure sensor connector.


q.

Reconnect the ECM connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR