Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.04–2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052600 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

When one of the following conditions is met, the brake warning light remains on:

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

The vacuum inside the brake booster decreases (for 1KD-FTV and 2KD-FTV).

·

The PKB terminal circuit is shorted.


WIRING DIAGRAM

C241039
5.417,5.365 5.719,5.542 0.302,0.177 10 false A13 5.417,5.604 6.958,6.042 1.542,0.438 10 false Skid Control ECU (Brake Actuator Assembly) 2.74,1.177 3.094,1.344 0.354,0.167 10 false G19 2.75,1.354 4.719,1.719 1.969,0.365 10 false Combination Meter Assembly 3.521,0.583 3.948,0.76 0.427,0.177 10 false Brake 4.531,0.271 4.74,0.438 0.208,0.167 10 false 36 2.063,0.292 2.25,0.469 0.188,0.177 10 false 21 0.458,0.354 1.406,0.667 0.948,0.313 10 false from IG Circuit 1.156,2.396 1.469,2.552 0.313,0.156 10 false A18 1.156,2.573 4.115,2.99 2.958,0.417 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly) 2.469,2.073 2.656,2.271 0.188,0.198 10 false 1 1.281,2.094 1.469,2.292 0.188,0.198 10 false 2 1.167,3.896 1.479,4.073 0.313,0.177 10 false K6 1.177,4.042 3.198,4.25 2.021,0.208 10 false Parking Brake Switch Assembly 2.479,3.51 2.667,3.708 0.188,0.198 10 false 1 2.479,4.927 2.667,5.125 0.188,0.198 10 false 1 1.146,5.521 3.531,5.813 2.385,0.292 10 false Vacuum Warning Switch Assembly* 1.146,5.344 1.604,5.521 0.458,0.177 10 false A19 0.146,6.385 2.094,6.573 1.948,0.188 10 false *: for 1KD-FTV and 2KD-FTV 5.792,3.625 6.198,3.875 0.406,0.25 10 false PKB 5.448,3.51 5.656,3.719 0.208,0.208 10 false 18 4.177,0.271 4.448,0.438 0.271,0.167 10 false SW 2.333,0.292 2.604,0.448 0.271,0.156 10 false IG+

CAUTION / NOTICE / HINT

NOTICE:
·

for 1KD-FTV and 2KD-FTV:

If there is a brake booster system malfunction, such as a problem with the response of the brake pedal when it is depressed, inspect the brake booster system first.



·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.

Turn the ignition switch to ON.


b.

With the brake fluid at the specified level, disconnect the brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector and check the brake warning light.

Result:
Result Proceed to
Brake warning light does not turn off A
Brake warning light turns off (for TMT Made) B
Brake warning light turns off (for TASA Made) C
Brake warning light turns off (for TDV Made) D
Brake warning light turns off (for TSAM Made) E


HINT:

If the brake warning light turns off, the brake fluid level warning switch (brake master cylinder reservoir sub-assembly) has an internal short circuit.




A

2.INSPECT PARKING BRAKE SWITCH ASSEMBLY

B

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

C

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

D

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

E

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.

Turn the ignition switch off.


b.

Remove the parking brake switch.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>REMOVAL


c.

Inspect the parking brake switch.

Click hereBrake>PARKING BRAKE>PARKING BRAKE SWITCH>INSPECTION

Result:
Result Proceed to
OK (for 1KD-FTV and 2KD-FTV) A
OK (except 1KD-FTV and 2KD-FTV) B
NG C




A

3.INSPECT VACUUM WARNING SWITCH ASSEMBLY

B

4.CHECK HARNESS AND CONNECTOR (BRAKE WARNING LIGHT CIRCUIT)

C

REPLACE PARKING BRAKE SWITCH ASSEMBLY

3.INSPECT VACUUM WARNING SWITCH ASSEMBLY
a.

Start the engine.


b.

Idle the engine.


c.

Disconnect the vacuum warning switch connector and check the brake warning light.

Result:
Result Proceed to
Brake warning light does not turn off A
Brake warning light turns off (for TMT Made) B
Brake warning light turns off (for TASA Made) C
Brake warning light turns off (for TDV Made) D
Brake warning light turns off (for TSAM Made) E


HINT:

If the brake warning light turns off, the vacuum warning switch has an internal short circuit.




A

4.CHECK HARNESS AND CONNECTOR (BRAKE WARNING LIGHT CIRCUIT)

B

REPLACE VACUUM WARNING SWITCH ASSEMBLY

C

REPLACE VACUUM WARNING SWITCH ASSEMBLY

D

REPLACE VACUUM WARNING SWITCH ASSEMBLY

E

REPLACE VACUUM WARNING SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE WARNING LIGHT CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G19 combination meter connector.


d.

Disconnect the parking brake switch connector.


e.

Disconnect the brake fluid level warning switch (brake master cylinder reservoir sub-assembly) connector.


f.

for 1KD-FTV and 2KD-FTV: Disconnect the vacuum warning switch connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-18 (PKB) - G19-36 (SW) Always Below 1 Ω
A13-18 (PKB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT SKID CONTROL ECU (PKB INTERNAL CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SKID CONTROL ECU (PKB INTERNAL CIRCUIT)
a.

Turn the ignition switch off.


b.

Release the parking brake.


c.

Start the engine.


d.

Disconnect the skid control ECU (brake actuator assembly) connector and check the brake warning light.

Result:
Result Proceed to
Brake warning light does not turn off A
Brake warning light turns off B


HINT:

If the brake warning light turns off, the skid control ECU (brake actuator assembly) has an internal short circuit.




A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B