Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.04–2012.10
RM1840EF _54 Brake _009623 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0052601 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1413  Front Speed Sensor RH Output Malfunction  C1275  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1414  Front Speed Sensor LH Output Malfunction  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1275 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) Stored during Test Mode.
·

Front speed sensor RH

·

Front skid control rotor RH


C1276 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) Stored during Test Mode.
·

Front speed sensor LH

·

Front skid control rotor LH


C1413 Front Speed Sensor RH Output Malfunction One of the following conditions is met:
1.

An open in the sensor signal circuit occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor RH

·

Speed sensor circuit

·

Front skid control rotor RH

·

Skid control ECU (Brake actuator assembly)


C1414 Front Speed Sensor LH Output Malfunction One of the following conditions is met:
1.

An open in the sensor signal circuit occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor LH

·

Speed sensor circuit

·

Front skid control rotor LH

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTCs C1413 and C1275 are for the front speed sensor RH.

·

DTCs C1414 and C1276 are for the front speed sensor LH.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open circuit detection Error or Normal Normal -
FL Speed Open Front speed sensor LH open circuit detection Error or Normal Normal -
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201
OK:

Normal (there are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor or disconnecting a connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)

NG

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2

f.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

3.PERFORM TEST MODE (SIGNAL CHECK)

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE (SIGNAL CHECK)
a.

Perform the signal check in the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3
OK:

All Test Mode DTCs are cleared.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

5.CHECK FRONT SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C108871
0.906,1.656 0.698,1.365 false 0.073,0.042 0.385,0.198 0.313,0.156 10 false *1 0.958,1.625 1.271,1.781 0.313,0.156 10 false *a 0.396,1.823 0.708,1.979 0.313,0.156 10 false *b 2.74,1.823 3.052,1.979 0.313,0.156 10 false *c
*1 Front Speed Sensor
*a No clearance
*b CORRECT
*c INCORRECT


Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR(for 4WD and Pre-Runner)>INSTALLATION

OK:

There is no clearance between the sensor and the steering knuckle.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT SPEED SENSOR TIP

NG

6.INSPECT FRONT SPEED SENSOR TIP
a.

Turn the ignition switch off.



c.

Check the speed sensor tip.

OK:

No scratches, oil or foreign matter on the sensor tip.


NOTICE:

Do not replace the speed sensor if no damage to the speed sensor tip is found.


HINT:
·

If the sensor is contaminated with oil or other foreign material, clean the sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction. Therefore, confirm that the rotor is not contaminated with foreign material before replacing the sensor.




Result:
Proceed to
OK
NG



OK

7.INSPECT FRONT SKID CONTROL ROTOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

7.INSPECT FRONT SKID CONTROL ROTOR
a.

Turn the ignition switch off.



c.

Check the front skid control rotor.

OK:

No scratches, oil or foreign matter on the rotor.



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SKID CONTROL ROTOR

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A36-7 (FR+) - A11-1 (FR+) Always Below 1 Ω
A36-7 (FR+) - Body ground Always 10 kΩ or higher
A36-6 (FR-) - A11-2 (FR-) Always Below 1 Ω
A36-6 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A36-19 (FL+) - A12-1 (FL+) Always Below 1 Ω
A36-19 (FL+) - Body ground Always 10 kΩ or higher
A36-18 (FL-) - A12-2 (FL-) Always Below 1 Ω
A36-18 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK TERMINAL VOLTAGE (FR+, FL+ TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TERMINAL VOLTAGE (FR+, FL+ TERMINAL)
a.

Turn the ignition switch off.


b.

Connect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the speed sensor connector.


d.
C190626
1.76,0.927 2.042,1.115 0.281,0.188 1.771,1.177 2.052,1.365 0.281,0.188 0.688,2.469 0.688,2.365 0.688,2.365 1.656,2.281 false 2.104,0.958 2.427,1.208 0.323,0.25 10 false *A 2.104,1.198 2.438,1.438 0.333,0.24 10 false *B 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 0.521,2.521 1.042,2.75 0.521,0.229 10 false FR+*A 0.521,2.719 1.083,2.938 0.563,0.219 10 false FL+*B 1.792,1.198 2.229,1.427 0.438,0.229 10 false A12 1.792,0.938 2.229,1.167 0.438,0.229 10 false A11
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
A11-1 (FR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
A12-1 (FL+) - Body ground Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

10.RECONFIRM DTC

NG

10.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

B

11.REPLACE FRONT SPEED SENSOR
11.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.



Result:
Proceed to
NEXT



NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

END

B