Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) J

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  Black Smoke Emitted  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Intake System
Symptom and Corresponding Main Fault
·

Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct

·

Black smoke (no lack of power) due to leakage between the turbo and intake manifold


Data List MAP

Glow System
Main fault Glow system malfunction
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Data List Check the glow plug indicator light
Diagnostic Point Measure the resistance of the glow plug

Engine
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cyl
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.




b.

Diesel Injection

Fuel Supply Pump
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
·

Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:
·

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.

·

When Target Pump SCV Current is 3000 mA or higher, the suction control valve has a tendency to become stuck.



Diagnostic Trouble Code Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

Injector Assembly
Main fault Blockage, increase in fuel injection volume
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



HINT:
·

When the sliding resistance of the internal parts of the injector assemblies (i.e. armature shaft, command piston and plunger) has increased due to internal contamination, injection quantity will increase at high common rail pressure due to a delay in injector assembly closure.

·

When black smoke occurs due to contamination of the injector assemblies, there are usually other symptoms, such as engine knocking noise at cold idling, rough idling, difficulty starting, etc. which are also present when the common rail pressure is low.



Injector Driver
Main fault Circuit fault: The injector assembly does not open.
Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List Same as injector assembly
Diagnostic Trouble Code When the injector driver has a fault, some DTCs may be stored.

Fuel Pressure Sensor (built into injector assembly)
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Press and Common Rail Pres Sens 2 follow Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Fuel Press or Common Rail Pres Sens 2 decreases to a value less than Target Common Rail Pressure).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel EGR

EGR System
Main fault
·

Does not move smoothly

·

Does not close completely


Symptoms
·

Rough idle

·

EGR valve stuck closed: A loud turbocharger sound.

·

EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).


Data List Actual EGR Valve Pos., Target EGR Position
·

Generally, Actual EGR Valve Pos. = Target EGR Position +/-5% (fully closed: 0%, fully open: 100%).

·

Using the EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Position (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

·

EGR valve is fully closed when the ignition switch is turned to ON (engine stopped).

·

EGR valve opens to the halfway point at idling after the engine is warmed up.


EGR Close Lrn. Val., EGR Close Lrn. Status
·

When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0 to 1 V.

·

In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.




d.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List
·

Actual Throttle Position

0%: Fully open

100%: Fully closed

·

When the ignition switch is ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.





Data List Related to Black Smoke


·

Engine Speed

·

MAP

·

MAF

·

Intake Air

·

Coolant Temp

·

Engine Speed of Cyl #1 (to #4)

(Output only when the "Check the Cylinder Compression" Active Test is performed)

·

Target Common Rail Pressure

·

Fuel Press

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Actual Throttle Position

·

Target EGR Position

·

Actual EGR Valve Pos.

·

EGR Close Lrn. Status

·

EGR Close Lrn. Val.



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing a Fuel Supply Pump, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


Explanation of Symptom


Black Smoke The fuel used in diesel engines has a higher boiling point and evaporates much slower than that used in gasoline engines. Additionally, the fuel is injected directly, so the air fuel mixture in diesel engines is formed in a very short period of time and is less homogenous. This is why diesel engines must operate with a larger air fuel ratio across the entire operating range. An insufficient quantity of air results in imperfect combustion and increased particulate (soot) emissions.
When the accelerator pedal is depressed, a large amount of fuel is injected. As a result, the air fuel ratio becomes rich. In this relatively rich environment, fuel droplets lacking in oxygen burn imperfectly producing soot, which is emitted as black smoke. In order to prevent black smoke production, the maximum injection quantity for a given intake air mass is limited (final injection quantity is limited by MAF).
Black smoke is emitted when either 1) a lack of oxygen is present during combustion, or 2) too much fuel is injected for a given intake air mass and the air fuel ratio becomes temporarily rich.


PROCEDURE

1.READ OUTPUT DTC (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the pending DTCs.

Result:
Result Proceed to
No DTCs are output A
Engine related DTCs are output B


HINT:

If only DTC P1609 is output, proceed to step 2.




A

2.CHECK FOR BLACK SMOKE

B

2.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat the above procedure *1 10 times or more.*2


e.

Check for black smoke emission during procedures *1 and *2.

OK:

Black smoke is emitted less than 5 times.


HINT:
·

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.

·

If the procedure is repeated 10 times or more and black smoke stops being emitted, this probably means that the black smoke was caused by a temporary accumulation of soot which occurred when driving at low speeds, and is not a malfunction.




Result:
Proceed to
OK
NG



OK

3.RECOVERY TO NORMAL

NG

4.CHECK AIR INTAKE SYSTEM
3.RECOVERY TO NORMAL
HINT:

If the racing procedure is repeated 10 times or more and black smoke stops being emitted, this probably means that the black smoke was caused by a temporary accumulation of soot which occurred when driving at low speeds, and is not a malfunction.


Result:
Proceed to
NEXT



NEXT

END

4.CHECK AIR INTAKE SYSTEM
a.

Check for air leakage and blockage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.

HINT:
·

Make sure that the air cleaner is not clogged and the intake and exhaust system hoses are not disconnected.

·

When the vacuum hoses are disconnected (the swirl control valve is always fully open) or the valve is stuck open, smoke may increase without feeling a lack of power (visually check the operation of the swirl control valve when starting the engine).

·

Check that the intercooler is not clogged with foreign matter.

·

Check that there are no disconnected, pinched or leaking hoses or pipes.

·

Check that there are no modifications made by the user.



OK:

No leakage or blockage.



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

5.CHECK WIRE HARNESS AND CONNECTION IN ENGINE COMPARTMENT
a.

Check the wire harness and connector connections of common rail system components.

OK:

The wire harnesses and connectors are connected securely.



Result:
Proceed to
OK
NG



OK

6.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data.


d.

Take a snapshot of the following Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

7.READ VALUE USING GTS (MAF AND MAP)
7.READ VALUE USING GTS (MAF AND MAP)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Data List / MAP and MAF.

Powertrain > Engine > Data List
Tester Display
MAF
MAP
50003 61 319,314

e.

Take a snapshot when the engine speed is maintained at 4000 rpm with no load.


f.

Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.

Result:
Result Proceed to
MAF 84 gm/s or more and MAP 105 kPa or higher A
Except above B


HINT:
·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc. Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.





A

8.CHECK SNAPSHOT (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #4)

B

37.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE)
8.CHECK SNAPSHOT (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #4)
a.

Check Injection Feedback Val # and Injection Volume in the snapshot taken after the engine is warmed up and idled for 1 minute.

Result:
Result Proceed to
Injection Volume is less than 10 mm3/st at 4000 rpm A
Injection Feedback Val for at least one cylinder is more than +3 mm3/st B
Except above C




A

9.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

11.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

C

18.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4)
9.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/ Glow Plug Controller)>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

15.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
11.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.

Powertrain > Engine > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
50004 61 111 492,493,494,495

d.

Check the engine speed during the Active Test.

Result:
Result Proceed to
Except below A
The values of Engine Speed Cyl #1 to #4 are within 10 rpm of each other B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

12.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

B

13.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4)
12.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the Active Test "Check the Cylinder Compression".


a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

13.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4)
a.

Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 5 when the engine was idling and at 4000 rpm.


b.

Record the value displayed for Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4.


Result:
Proceed to
NEXT



NEXT

14.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
14.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
NOTICE:
·

Replace the injector assembly of the cylinder which displays a value of 3.0 mm3/st or higher for Injection Feedback Val #1 to #4 in step 8.

·

Only replace the injector assembly for the cylinder which displays an Injector Leaking Count #1 to #4 value of 1 or more, or i-ART Learning Status History #1 to #4 value of 1 Trip or more.

·

If Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 both display 0, only replace the injector assembly for the cylinder which was determined to be malfunctioning using Injection Feedback Val #1 to #4.



a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/ Glow Plug Controller)>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

15.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
15.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
a.

Clean the fuel filter case and replace the fuel filter.

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

16.BLEED AIR FROM FUEL SYSTEM
16.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

17.CHECK FOR BLACK SMOKE
17.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat the above procedure *1 10 times.*2


e.

Check for black smoke emission during procedures *1 and *2.

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
NEXT



NEXT

END

18.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4)
a.

Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 5 when the engine was idling and at 4000 rpm.

Result:
Result Proceed to
The value for Injector Leaking Count #1 to #4 does not change from 0
The value for i-ART Learning Status History #1 to #4 does not change from 0 Trip
A
The value for Injector Leaking Count #1 to #4 displays 1 or more
The value for i-ART Learning Status History #1 to #4 displays 1 Trip or more
B




A

19.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)

B

32.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
19.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / MAP and Atmosphere Pressure.

Powertrain > Engine > Data List
Tester Display
Atmosphere Pressure
MAP
50003 61 64,314

d.

Compare MAP to Atmosphere Pressure when the ignition switch is turned to ON (engine stopped).

HINT:
·

If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 10 kPa (0.1 kgf/cm2, 1.5 psi) or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

Standard atmospheric pressure is 101 kPa (1.0 kgf/cm2, 15 psi). For every 100 m (328 ft.) increase in elevation, pressure drops by 1 kPa (0.01 kgf/cm2, 0.1 psi). This varies by weather (high atmospheric pressure, low atmospheric pressure).



Result:
Result Proceed to
MAP and Atmosphere Pressure have same value A
Atmosphere Pressure is different from actual atmospheric pressure B
MAP is different from actual atmospheric pressure C




A

20.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)

B

23.REPLACE ECM

C

26.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
20.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Fuel Press
50004 61 90 706,54

d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E11
3.385,2.438 3.5,2.104 3.5,2.104 3.573,2.104 false 4.385,2.667 4.99,2.49 4.99,2.49 5.052,2.49 true 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 true 3.708,3.281 3.938,4.198 3.938,4.198 4.073,4.198 false 0.083,1.427 1.51,1.729 1.427,0.302 10 false Active Test Operation 0.167,0.594 1.573,0.875 1.406,0.281 10 false Engine Speed (rpm) 0.563,3.26 1.469,3.5 0.906,0.24 10 false Fuel Pressure 3.604,2.031 4.948,2.313 1.344,0.281 10 false Target Fuel Pressure 6.469,4.146 6.906,4.354 0.438,0.208 10 false Time 2.198,2.427 2.875,2.813 0.677,0.385 10 false Less than 10000 kPa 3,4.281 3.76,4.531 0.76,0.25 10 false 2 seconds 5.104,2.396 6.01,2.802 0.906,0.406 10 false Abnormal Fuel Pressure 2.438,1.135 3.115,1.333 0.677,0.198 10 false Test Start 4.177,1.135 4.844,1.333 0.667,0.198 10 false Test Stop 5.604,1.135 6.281,1.333 0.677,0.198 10 false Test Start 2.208,1.823 2.969,2.302 0.76,0.479 10 false Normal Fuel Pressure 1.646,0.281 2.021,0.448 0.375,0.167 10 false 2000 1.885,0.844 2.052,1.01 0.167,0.167 10 false 0 1.75,1.313 2.073,1.479 0.323,0.167 10 false ON 1.698,1.573 2.021,1.74 0.323,0.167 10 false OFF 4.146,4.146 5.719,4.615 1.573,0.469 10 false Pressure Discharge Valve Abnormal Fuel Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa (102.0 kgf/cm2, 1451 psi).


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Fuel Press" is the actual fuel pressure in common rail assembly.

·

When the pressure discharge valve on the common rail assembly has a malfunction, the actual fuel pressure changes as shown by "Pressure Discharge Valve Abnormal Fuel Pressure" in the illustration.

·

The pressure discharge valve operates to discharge fuel pressure when the internal pressure of the common rail exceeds the target fuel pressure.

·

There are 2 fuel pressure sensor circuits and both of them display the same value. If the difference between Fuel Press and Common Rail Press Sens 2 exceeds 10000 kPa (102 kgf/cm2, 1451 psi) for 2 seconds or more, it is necessary to inspect or repair the wiring for the No. 1 and No. 4 injector assemblies.




Result:
Proceed to
OK
NG



OK

21.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)

NG

27.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
21.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Soak the engine for a long time.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309
OK:

Coolant Temp is the same as the ambient temperature.


HINT:

When the engine coolant temperature is low even though the engine has been fully warmed up, or when the engine coolant temperature is high even though the engine is cold, inspect the sensor.



Result:
Proceed to
OK
NG



OK

22.READ VALUE USING GTS (INTAKE AIR AND INTAKE AIR TEMP (TURBO))

NG

24.CHECK AND REPLACE COOLANT TEMPERATURE SENSOR
22.READ VALUE USING GTS (INTAKE AIR AND INTAKE AIR TEMP (TURBO))
a.

Connect the GTS to the DLC3.


b.

Soak the engine for a long time.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air, Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air
Intake Air Temp (Turbo)
50003 61 318,240
OK:

Intake Air is the same as Intake Air Temp (Turbo).



Result:
Proceed to
OK
NG



OK

35.CHECK FOR BLACK SMOKE

NG

25.CHECK AND REPLACE MALFUNCTIONING PARTS
23.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
24.CHECK AND REPLACE COOLANT TEMPERATURE SENSOR
a.

b.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
25.CHECK AND REPLACE MALFUNCTIONING PARTS


c.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>MASS AIR FLOW METER(w/ Glow Plug Controller)>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



d.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR(w/ Glow Plug Controller)>REMOVAL

HINT:

It is only necessary to replace the part when the results of the inspection indicate a problem.



Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
26.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
27.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-1 - C163-23 (PCV+) Always Below 1 Ω
C5-2 - C163-12 (PCV-) Always Below 1 Ω
C5-1 or C163-23 (PCV+) - Body ground Always 10 kΩ or higher
C5-2 or C163-12 (PCV-) - Body ground Always 10 kΩ or higher



d.

Reconnect the suction control valve connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

28.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP

NG

36.REPAIR OR REPLACE HARNESS OR CONNECTOR
28.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
a.

Disconnect the inlet hose from the Fuel Supply Pump.


b.

Operate the priming pump and check that fuel is being supplied to the Fuel Supply Pump.

OK:

Fuel is properly supplied to the Fuel Supply Pump when the priming pump is operated.


HINT:
·

When there is a lack of fuel, the fuel pressure drops.

·

Inspect for fuel filter clogging (check that the fuel filter is not clogged).




c.

Reconnect the inlet hose.


Result:
Proceed to
OK
NG



OK

29.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

NG

33.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
29.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

Result:
Proceed to
NEXT



NEXT

30.BLEED AIR FROM FUEL SYSTEM
30.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

31.PERFORM SUPPLY PUMP INITIALIZATION
31.PERFORM SUPPLY PUMP INITIALIZATION
a.

Perform fuel supply pump initialization.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION

Powertrain > Engine > Utility
Tester Display
Supply Pump Initialization
50005 61 163

Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
32.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
NOTICE:

Only replace the injector assembly for the cylinder which displays an Injector Leaking Count #1 to #4 value of 1 or more, or i-ART Learning Status History #1 to #4 value of 1 Trip or more.


a.

Replace the injector assembly.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/ Glow Plug Controller)>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

15.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
33.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP)
a.

Check and replace the clogged fuel pipe.


Result:
Proceed to
NEXT



NEXT

34.BLEED AIR FROM FUEL SYSTEM
34.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
35.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat the above procedure *1 10 times.*2


e.

Check for black smoke emission during procedures *1 and *2.

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
NEXT



NEXT

END

36.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

35.CHECK FOR BLACK SMOKE
37.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / MAF.


f.

Read the MAF value displayed on the GTS while the engine is idling.


g.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Valve Close.

Powertrain > Engine > Active Test
Active Test Display
Activate the EGR Valve Close
Data List Display
MAF
50004 61 183 319

h.

Read the MAF value when the EGR valve is closed using the Active Test function.

HINT:
·

If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.

·

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.



Result:
Active Test Result Proceed to
Activate the EGR Valve Close:
Off (Open) to On (Closed)
MAF value does not change A
MAF value changes B


NOTICE:

As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter.


Reference:
EGR Valve Condition (Opening) Measuring Condition MAF (Reference)
Open (55%)
·

Atmosphere pressure: 101 kPa

·

Intake air temperature: 30°C (86°F)

·

Engine coolant temperature: 88°C (190°F)


3 to 10 gm/s
Closed (0%) 12 to 21 gm/s




A

38.READ VALUE USING GTS (MAF)

B

8.CHECK SNAPSHOT (INJECTION VOLUME AND INJECTION FEEDBACK VAL #1 TO #4)
38.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / MAF.

Powertrain > Engine > Data List
Tester Display
MAF
50003 61 319

d.

With the ignition switch ON and engine stopped, read the value when 30 seconds has elapsed.

Standard:
GTS Display Switch Condition Standard
MAF Ignition switch ON (do not start engine) Less than 0.35 gm/s



Result:
Proceed to
OK
NG



OK

39.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EGR COOLER BYPASS)

NG

42.REPLACE MASS AIR FLOW METER
39.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EGR COOLER BYPASS)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off and wait for 30 seconds.


d.

Start the engine and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / MAF.


f.

Read the MAF value displayed on the GTS while the engine is idling.


g.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / EGR Cooler Bypass Position.

HINT:

Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.


Powertrain > Engine > Active Test
Active Test Display
Activate the VSV for EGR Cooler Bypass
Data List Display
MAF
50004 61 181 319

h.

Using the Active Test function, switch the EGR valve bypass switching valve between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".

HINT:

If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.


Result:
Activate Test Result Proceed to
Activate the VSV for EGR Cooler Bypass:
Cooler to Bypass
MAF value does not change A
MAF value changes B


HINT:

If the EGR cooler is clogged, the mass air flow changes.




A

40.REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

B

41.REPLACE EGR COOLER
40.REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR VALVE(w/ Glow Plug Controller)>REMOVAL


b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.

·

When cleaning the electric EGR control valve assembly, perform initialization procedure.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.



HINT:
·

If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.

·

If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the electric EGR control valve assembly.




c.

Result:
Proceed to
NEXT



NEXT

41.REPLACE EGR COOLER
41.REPLACE EGR COOLER

Result:
Proceed to
NEXT



NEXT

17.CHECK FOR BLACK SMOKE
42.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>MASS AIR FLOW METER(w/ Glow Plug Controller)>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

17.CHECK FOR BLACK SMOKE