Home › TRANSMISSION ยท R150F / R151F MANUAL TRANSMISSION › MANUAL TRANSMISSION ASSEMBLY

MANUAL TRANSMISSION ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here)



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE CONSOLE BOX ASSEMBLY
(Click here)


4. REMOVE SHIFT LEVER BOOT ASSEMBLY


G034544E03
  1. Remove the 4 screws, 2 clips and shift lever boot.



5. REMOVE FLOOR SHIFT SHIFT LEVER ASSEMBLY


G021695E06
  1. Cover the shift lever cap with a cloth.

  1. Press down on the shift lever cap and rotate it counterclockwise to remove it.

  1. Pull out the shift lever.



6. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY


G021696E04
  1. Using needle nose pliers, remove the snap ring and pull out the shift lever.

    HINT:
    Move the transfer shift lever to the H4 position.



7. REMOVE TRANSFER CASE LOWER PROTECTOR
  1. Remove the 4 bolts and transfer case lower protector.



8. REMOVE NO. 1 ENGINE UNDER COVER


9. REMOVE NO. 2 ENGINE UNDER COVER


10. DRAIN MANUAL TRANSMISSION OIL
  1. Remove the drain plug and gasket to drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



11. REMOVE REAR PROPELLER SHAFT ASSEMBLY
for DANA made: (Click here)
except DANA made: (Click here)


12. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


13. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the front exhaust pipe.
    for 1KD-FTV: (Click here).
    for 2TR-FE: (Click here).
    for 1GR-FE: (Click here).



14. DISCONNECT WIRE HARNESS
  1. Transmission side:
    Disconnect the back-up light switch connector.

  1. Transfer side:
    Disconnect the No. 1, No. 2 and No. 3 transfer indicator switch connectors, and vehicle speed sensor connector.



15. DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY (except 1GR-FE)


G034223E01
  1. Remove the 2 bolts and disconnect the release cylinder.



16. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY (for 1GR-FE)


C112617
  1. Remove the bolts, nut and release cylinder heat insulator.



    C112615
  1. Using a union nut wrench, remove the flexible tube.

    HINT:
    Use a container to catch the fluid.



    C112616
  1. Disconnect the flexible hose tube from the clutch release cylinder.

  1. Remove the bolt and 2 way.



    C112662
  1. Remove the 2 bolts and release cylinder.



    D030415
  1. Using a union nut wrench, disconnect the 2 flexible hose tubes.



17. REMOVE STARTER ASSEMBLY
  1. Remove the starter.
    for 2TR-FE: (Click here)
    for 1GR-FE 1.6 kW Type: (Click here)
    for 1KD-FTV BOSCH made: (Click here)
    for 1KD-FTV DENSO made: (Click here)



18. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034218E04
  1. Support the transmission rear side with a support stand.

  1. Remove the 4 set bolts of the rear No. 1 engine mounting insulator.

  1. Remove the 4 bolts, 4 nuts and frame crossmember.



19. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


G034219E05
  1. Remove the 4 bolts and engine mounting insulator.



20. REMOVE EXHAUST MANIFOLD STAY (for 2TR-FE)


B086194E01
  1. Remove the 3 bolts and exhaust manifold stay.



21. REMOVE STIFFENER PLATE (for 1KD-FTV)


G034607E04
  1. Remove the 4 bolts and stiffener plate RH.

  1. Remove the 4 bolts and stiffener plate LH.



22. REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY


C113299E08
  1. Using a transmission jack, support the transmission.

  1. Remove the support stand from the rear side.

  1. 1KD-FTV:
    Remove the 5 bolts and transmission.

  1. 2TR-FE:
    Remove the 7 bolts and transmission.

  1. 1GR-FE:
    Remove the 9 bolts and transmission.



23. REMOVE TRANSFER ASSEMBLY
  1. Remove the transfer (Click here).