Home › ENGINE ยท 1KD-FTV › ENGINE MECHANICAL › ENGINE ASSEMBLY (w/o Glow Plug Controller)

ENGINE ASSEMBLY (w/o Glow Plug Controller) > INSTALLATION

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.



1. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH
  1. Install the front No. 1 engine mounting bracket with the 4 bolts.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }



2. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH
  1. Install the front No. 1 engine mounting bracket with the 4 bolts.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }



3. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
  1. Install a new gasket to the engine coolant temperature sensor.

  1. Install the engine coolant temperature sensor.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the engine coolant temperature sensor connector.



4. INSTALL CAMSHAFT POSITION SENSOR
  1. Apply a light coat of engine oil to the O-ring of the sensor.

  1. Install the camshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Connect the camshaft position sensor connector.



5. INSTALL CRANKSHAFT POSITION SENSOR
  1. Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.

  1. Install the crankshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Attach the 3 clips and connect the crankshaft position sensor connector.

    NOTICE:
    Insert the crankshaft position sensor wire harness into the protrusions of the timing gear cover.



6. INSTALL VANE PUMP ASSEMBLY
  1. Install a new O-ring to the vane pump.

  1. Install the vane pump with the 2 nuts.

    Torque:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }



7. INSTALL VACUUM PUMP ASSEMBLY
  1. Install 2 new O-rings to the vacuum pump.

  1. Install the vacuum pump with the 2 nuts.

    Torque:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }



8. INSTALL TIMING GEAR COVER INSULATOR (w/ EGR Cooler)
  1. Install the gear cover insulator with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



9. INSTALL OIL COOLER COVER SUB-ASSEMBLY
  1. Install a new gasket and the oil cooler cover with the 13 bolts and 2 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Connect the oil pressure connector and install the wire harness.



10. INSTALL FUEL SUPPLY PUMP ASSEMBLY


A070715E01
  1. Check that the injection gear in the timing gear case moves back and forth smoothly.

  1. Install a new O-ring to the pump.

  1. Apply a light coat of engine oil to the O-ring.



    A060835E01
  1. Align the set key on the drive shaft with the groove of the injection gear.



    A098897E01
  1. Install the pump with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Set a new O-ring before tightening the set nut.



    A070711E01
  1. Using SST, hold the crankshaft pulley and install the set nut.

    SST
    09213-58013  
    09330-00021  

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



    A071144E01
  1. Move the pump drive shaft pulley back and forth to check the thrust clearance of the injection pump drive shaft.

    Standard thrust clearance:
    0.15 to 0.55 mm (0.0059 to 0.0217 in.)

    If the clearance is not within the specified range, disassemble and reassemble the supply pump and pump drive shaft pulley. Then repeat the step above.



    A098896E01
  1. Connect the 2 connectors.



    A098895E01
  1. Connect the 2 fuel hoses.



    A098974E10
  1. Temporarily install the fuel inlet pipe with the union nuts.

    NOTICE:
    1. If the supply pump is replaced, the fuel inlet pipe must be replaced.
    2. Keep the fuel inlet pipe free of foreign matter.

  1. Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf } for use with union nut wrench
    35 N*m{ 357 kgf*cm , 26 ft.*lbf } for use without union nut wrench

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

  1. Using a 17 mm union nut wrench, tighten the injection pipe union nut on the supply pump side.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf } for use with union nut wrench
    35 N*m{ 357 kgf*cm , 26 ft.*lbf } for use without union nut wrench

    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

  1. Install the oil dipstick guide with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    G036615E01
  1. Install the clamp with the bolt.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



11. INSTALL COMMON RAIL ASSEMBLY
  1. Install the common rail and No. 2 intake manifold insulator with the 2 bolts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Connect the 2 connectors.



12. INSTALL FUEL INLET PIPE SUB-ASSEMBLY
  1. Temporarily install the fuel inlet pipe with the union nuts.

    NOTICE:
    1. When replacing the common rail, it is necessary to replace the 4 injection pipes and fuel inlet pipe with new ones.
    2. Be careful that dust, dirt or any other foreign matter does not contact the joint area of the fuel inlet pipe.

  1. Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the common rail side.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the supply pump side.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



13. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.



    A060101E02
  1. Using SST, tighten the oil filter. Depending on the work space available, choose from the following.

    SST
    09228-07501  

    1. If enough space is available, use a torque wrench to tighten the oil filter.

      Torque:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    2. If enough space is not available to use a torque wrench, tighten the oil filter 3/4 turn by hand or with a common wrench.



14. INSTALL GLOW PLUG ASSEMBLY
(Click here)


15. INSTALL INTAKE MANIFOLD
(Click here)


16. INSTALL DIESEL THROTTLE BODY ASSEMBLY
  1. Install a new gasket and the diesel throttle body with the 2 bolts and 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 connectors.



17. INSTALL WATER OUTLET


    A098977E03
  1. Install a new gasket to the cylinder head as shown in the illustration.
    Text in Illustration 
    *1
    Claw

    HINT:
    Make sure the claws of the gasket face the water outlet.

  1. Install the water outlet with the 2 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



18. INSTALL THERMOSTAT


    A110388E01
  1. Install a new gasket to the thermostat.

    HINT:
    When installing the thermostat to the gasket, be careful not to deform the gasket. Make sure that the thermostat is properly installed into the groove of the gasket, as shown in the illustration.

  1. Insert the thermostat into the cylinder block with the jiggle valve facing straight upward.

    HINT:
    The jiggle valve may be set within 30°of either side of the prescribed position.



19. INSTALL WATER INLET


    A097637E01
  1. Install the inlet with the 3 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



20. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET
  1. Install the No. 1 compressor mounting bracket with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



21. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A097638E05
  1. Install the V-ribbed belt tensioner with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    Text in Illustration 
    *1
    Cylinder Block
    *2
    V-ribbed Belt Tensioner

    HINT:
    Firmly press and hold the V-ribbed belt tensioner against the cylinder block to eliminate any gaps in the areas labeled A in the illustration. Then uniformly tighten the 4 bolts.



22. INSTALL GENERATOR BRACKET
  1. Install the generator bracket with the bolt.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



23. INSTALL GENERATOR ASSEMBLY


A111821E01
  1. Install the generator and adjusting bar with the 2 bolts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf } for bolt A
    25 N*m{ 255 kgf*cm , 18 ft.*lbf } for bolt B

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the generator connector.



24. INSTALL NO. 2 IDLE PULLEY ASSEMBLY
  1. Install the spacer, No. 2 idle pulley and pulley plate with the bolt.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



25. INSTALL EXHAUST MANIFOLD
  1. Temporarily install a new gasket, the exhaust manifold, 8 new collars and the 8 plate washers to the cylinder head with 8 new nuts.



    A260675E01
  1. Tighten the 8 nuts in the order shown in the illustration.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.



26. INSTALL TURBOCHARGER SUB-ASSEMBLY


A098818E01
  1. Temporarily install a new gasket and the turbocharger with 3 new nuts.

    HINT:
    When installing the turbo oil pipe, loosely install the 3 nuts so that the turbocharger and cylinder head can be aligned easily.



  1. Temporarily install the turbo oil pipe.

    HINT:
    Before installing the oil pipe, clean it.


    1. Install a new gasket and the oil pipe with the 2 nuts, but only loosely install the nuts.

      NOTICE:
      The notch (narrow part) of the gasket must face the engine.

    2. Install a new gasket and the oil pipe with the 2 bolts, but only loosely install the bolts.

      NOTICE:
      The claws of the gasket must face the pipe.



    3. Install a new gasket and the oil pipe with the union bolt, but only loosely install the union bolt.


      A110343E01



    4. A099944E03
    5. Temporarily install the turbocharger stay with the 3 bolts.

  1. Tighten the 3 nuts of the turbocharger.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. Tighten the 2 nuts and 2 bolts of the oil pipe, and the union bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf } for bolt

    Torque:
    13 N*m{ 133 kgf*cm , 9 ft.*lbf } for nut

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf } for union bolt

  1. Tighten the 3 bolts of the turbocharger stay.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }



27. INSTALL TURBINE OUTLET ELBOW


    A098816E01
  1. Install a new gasket and the outlet elbow with the 3 nuts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }



28. INSTALL NO. 1 TURBO WATER HOSE


A098815E01
  1. Connect the 2 hoses to the 2 tubes.

  1. Move the 2 clamps to the locations where the hoses and tubes are connected.



29. INSTALL NO. 1 TURBO INSULATOR


A110342
  1. Temporarily install the turbo insulator with the bolt.



30. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
  1. Temporarily install the heat insulator with the 2 bolts.

  1. Tighten the bolt of the turbo insulator, and the 2 bolts of the heat insulator.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



31. INSTALL COMPRESSOR INLET ELBOW


A110341
  1. Install a new gasket and inlet elbow with the 2 nuts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Connect the ventilation pipe to the cylinder head cover.

  1. Move the clamp to the joint pipe of the hose.

  1. Install the ventilation pipe with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 connectors to the turbocharger.

  1. Install the harness clamp's clip to the inlet elbow.



32. INSTALL NO. 1 INTERCOOLER SUPPORT BRACKET
  1. Install the No. 1 intercooler support bracket with the 2 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



33. INSTALL NO. 2 INTERCOOLER SUPPORT BRACKET
  1. Install the No. 2 intercooler support bracket with the 2 bolts.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }



34. INSTALL CRANKSHAFT PULLEY
  1. Align the keyway of the pulley with the key located on the crankshaft, and then slide the pulley into place to install it.



    A251844E01
  1. Using SST, install the pulley bolt.

    SST
    09213-58014  
    09330-00021  

    Torque:
    365 N*m{ 3722 kgf*cm , 269 ft.*lbf }



35. INSTALL TIMING BELT


A070691E02
  1. Check that the timing marks are aligned as shown in the illustration.

    HINT:
    If reusing the timing belt, align the points marked during removal, and install the belt with the arrow pointing in the direction of engine revolution.

    NOTICE:
    1. The engine should be cold.
    2. When turning the crankshaft, the valve heads will hit against the piston's top position. Do not turn it more than necessary.

  1. Using a 10 mm hexagon wrench, install the timing belt idler pulley and new washer with the bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. Check that the idler pulley moves smoothly.
    If it does not move smoothly, check the idler sub-assembly and washer.

  1. Install the timing belt to the pump drive shaft pulley, camshaft timing pulley and No. 1 timing belt idler in sequence.



    A070548E01
  1. Place the tensioner upright. Then set a press to the top of the tensioner.

    NOTICE:
    1. Do not scratch or deform the rod end.
    2. Press in the tensioner rod upward.
    3. Protect the tip of the push rod with a cloth in order to prevent damage.

  1. Using the press, slowly push in the push rod using 981 to 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) of force.

    NOTICE:
    Do not impose a load of over 9,807 N (100 to 1,000 kgf, 220 to 2,205 lbf) to the push rod.

  1. Align the holes of the push rod and housing. Then pass a 1.5 mm hexagon wrench through the holes to keep the setting position of the push rod.

  1. Install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.

  1. Tighten the 2 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Uniformly tighten the 2 bolts and install the tensioner.



    A059983E01
  1. Remove the 1.5 mm hexagon wrench from the tensioner.



    A070549E02
  1. Turn the crankshaft clockwise 720° and check that the timing marks are aligned as shown in the illustration.



36. INSTALL NO. 1 TIMING BELT COVER
  1. Install the timing belt cover with the 6 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the wire harness clamp.

  1. Install the water hose clamp with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



37. INSTALL FRONT ENGINE MOUNTING INSULATOR
  1. Install the 2 front engine mounting insulators with the 2 nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }



38. INSTALL ENGINE WIRE
  1. Install the engine wire to the engine.



39. INSTALL ENGINE HANGERS


    A224109E01
  1. Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    NOTICE:
    Install the engine hangers with new bolts.

    HINT:
    Part No.
    No. 1 Engine Hanger
    12284-30020
    No. 2 Engine Hanger
    12282-67030
    Bolt
    91552-81014 and 91642-81030



40. REMOVE ENGINE FROM ENGINE STAND
  1. Attach an engine sling device and hang the engine with a chain block.

  1. Remove the engine from the engine stand.



41. INSTALL ENGINE ASSEMBLY
  1. Slowly lower the engine into the engine compartment.

  1. Install the engine with the 4 bolts and 4 nuts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. Remove the 2 bolts and 2 engine hangers.



42. INSTALL REAR END PLATE
  1. Install the rear end plate with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



43. INSTALL PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)
  1. Clean the bolts and their holes.



    A072851E02
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-58014  
    09330-00021  



    A271170E01
  1. Install the flywheel and ring gear, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.
    Text in Illustration 
    *1
    Flywheel and Ring Gear
    *2
    Pump Impeller Drive Plate
    *3
    Rear Drive Plate Spacer
    *a
    Engine Side
    *b
    Transmission Side

    NOTICE:
    Align either hole in the pump impeller drive plate and either hole in the rear drive plate spacer with the knock pin of the flywheel and ring gear, and then install the flywheel and ring gear, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.

    HINT:
    As the rear drive plate spacer and pump impeller drive plate are not reversible, be sure to install them in the direction shown in the illustration.



    A114804E01
  1. Install and uniformly tighten and tighten the 8 bolts in several steps in the sequence shown in the illustration.

    Torque:
    178 N*m{ 1815 kgf*cm , 131 ft.*lbf }

    NOTICE:
    Do not start the engine for at least an hour after installing the flywheel and ring gear.



44. INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
  1. Clean the bolts and their holes.

  1. Apply adhesive to 2 or 3 threads at the end of each bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    A072424E02
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-58014  
    09330-00021  

  1. Install the flywheel to the crankshaft.



    A114803E01
  1. Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    178 N*m{ 1815 kgf*cm , 131 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 1 hour after installation.



45. INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)


    C226320
  1. Insert SST into the clutch disc. Then insert SST (together with the clutch disc) into the flywheel.

    SST
    09301-00110  

    NOTICE:
    Make sure not to insert the clutch disc facing the wrong direction.



46. INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)


    D029623E03
  1. Align the matchmarks on the clutch cover and flywheel.

  1. Tighten the 6 bolts as described below.

    1. Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.

    2. Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.

      Torque:
      19 N*m{ 195 kgf*cm , 14 ft.*lbf }

  1. Lightly move SST up and down, and right and left.

    SST
    09301-00110  

  1. Check that the disc is in the center, and then tighten the bolts.



47. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)


    D029624E01
  1. Using a dial indicator with roller instrument, measure the diaphragm spring tip alignment.

    Maximum misalignment:
    0.5 mm (0.020 in.)


    1. D029625E03
      If the misalignment is greater than the maximum, use SST to adjust the diaphragm spring tip alignment.
    SST
    09333-00013  



48. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:
Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.

  1. Install the rear No. 1 engine mounting insulator with the 4 bolts.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



49. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)


50. INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for Automatic Transmission)


51. INSTALL MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
(Click here)


52. CONNECT COOLER COMPRESSOR ASSEMBLY
  1. Connect the cooler compressor with the 4 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



53. CONNECT WIRE HARNESS
  1. Connect the 4 ECM connectors.

  1. for Automatic Transmission:
    Connect the 3 TCM connectors.

  1. Connect the turbo motor driver connector.

  1. for 4WD:
    Connect the 4WD control ECU connector.

  1. Connect the 3 injector driver connectors.

  1. Attach the clamp and connect the wire harness with the 2 nuts.

    Torque:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }

  1. Connect the ground cable with the bolt.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Connect the 2 engine room junction block connectors.

  1. Connect the engine room junction block wire with the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Install the side engine room relay block cover.

  1. Install the upper relay block cover.



54. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


B278068E01
  1. Attach the 2 hinges to install the glove compartment door.
    Text in Illustration 
    *1
    Hinge



    B278069E01
  1. While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.
    Text in Illustration 
    *1
    Stopper



55. CONNECT UNION TO CONNECTOR TUBE HOSE
  1. Connect the union to connector tube hose.



56. CONNECT FUEL HOSE
  1. Connect the 2 fuel hoses.



57. CONNECT PRESSURE FEED TUBE ASSEMBLY
  1. Connect the pressure feed tube.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).

  1. Connect the oil reservoir to pump hose.



58. CONNECT HEATER HOSE
  1. Connect the 2 heater hoses.



59. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(Click here)


60. INSTALL FRONT PROPELLER SHAFT ASSEMBLY


F052086E01
  1. Align the matchmarks on the yoke and transfer flange.

  1. Connect the propeller shaft with the 4 washers and 4 nuts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



    C098708E01
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft with the 4 bolts, 4 washers and 4 nuts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



61. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(Click here)


62. INSTALL STARTER ASSEMBLY
  1. for 2.2 kW Type Bosch Made: (Click here)
  2. for 2.2 kW Type Denso Made: (Click here)


63. INSTALL RADIATOR ASSEMBLY
(Click here)


64. INSTALL INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR
(Click here)


65. INSTALL AIR CLEANER ASSEMBLY
  1. Connect the air cleaner hose.

  1. Install the cleaner with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Tighten the hose clamp.

  1. Connect the connector to the mass air flow meter connector.



66. INSTALL BATTERY TRAY


67. INSTALL BATTERY


68. INSTALL BATTERY CLAMP SUB-ASSEMBLY
  1. Install the battery clamp with the bolt and nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



69. ADD POWER STEERING FLUID


70. ADD TRANSMISSION FLUID (for Automatic Transmission)
  1. Add automatic transmission fluid (Click here).

    Fluid type:
    Toyota Genuine ATF TYPE T-IV



71. ADD TRANSMISSION OIL (for Manual Transmission)


D025304E08

Oil grade:
GL-4

Viscosity:
SAE 75W-90

Standard capacity:
2.2 liters (2.3 US qts, 1.9 Imp. qts)

Torque:
37 N*m{ 377 kgf*cm , 27 ft.*lbf }



72. ADD ENGINE OIL
  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }

  1. Add new oil.

    Standard oil capacity:

    Item
    Specified Condition
    Drain and refill with oil filter change
    6.9 liters (7.3 US qts, 6.1 Imp. qts)
    Drain and refill without oil filter change
    6.6 liters (7.0 US qts, 5.8 Imp. qts)
    Dry fill
    7.4 liters (7.8 US qts, 6.5 Imp. qts)

  1. Install the oil filler cap.



73. INSTALL HOOD SUB-ASSEMBLY
  1. Install the hood with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Connect the washer nozzle hose.

  1. Adjust the hood (Click here).



74. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



75. BLEED AIR FROM FUEL SYSTEM


    A098962E02
  1. Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

    NOTICE:
    1. Hand pump pumping speed: Max. 2 strokes/ sec.
    2. The hand pump must be pushed with a full stroke during pumping.
    3. When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
    4. If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
    5. If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
    6. If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.

  1. Start the engine.

    NOTICE:
    1. Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
    2. Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
    3. Use a fully-charged battery.


    1. When the engine can be started, proceed to the next step.

    2. If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Clear the DTCs.

    1. w/ EGR Cooler: (Click here)
    2. w/o EGR Cooler: (Click here)

  1. Start the engine.*1



    A194065E03
  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

  1. Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3



  1. Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.


    A192848E05

    HINT:
    When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

  1. Clear the DTCs.

    1. w/ EGR Cooler: (Click here)
    2. w/o EGR Cooler: (Click here)

    HINT:
    It is necessary to clear the DTCs as DTC P1604 or P1605 may be stored when air is bled from the fuel system after replacing or repairing fuel system parts.

  1. Repeat steps *1 to *3.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read Current DTCs.

    OK:
    No DTCs are output.



76. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    A098989E01
  1. Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.

    Standard capacity:
    Item
    Specified Condition
    A/T
    11.1 liters (11.7 US qts, 9.8 Imp. qts)
    M/T
    9.8 liters (10.4 US qts, 8.6 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Please contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.



    A099591E01
  1. Using a wrench, install the vent plug.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

    2. Maintain the engine speed at 2,500 to 3,000 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      1. Be careful as the radiator hoses are hot.
      1. Keep your hands away from the radiator fan.

    4. Stop the engine and wait until the coolant cools down to ambient temperature.

      CAUTION:
      Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    G036768E01
  1. After the coolant cools down, check that the coolant level is at the F line.
    If the coolant level is below the F line, add TOYOTA SLLC to the F line.



77. BLEED AIR FROM POWER STEERING SYSTEM
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the steering wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the steering wheel to the left or right full lock position and hold it there for 2 to 3 seconds. Then turn the steering wheel to the opposite full lock position and hold it there for 2 to 3 seconds.

    2. Repeat the step above several times.

  1. Stop the engine.



    F040897E01
  1. Check for foaming or emulsification. If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.

  1. Check the fluid level.



78. INSPECT POWER STEERING FLUID LEVEL


    F040898E01
  1. Keep the vehicle level.

  1. With the engine stopped, check the power steering fluid level in the oil reservoir. If necessary, add power steering fluid.

    Power steering fluid (for TMT made):
    "TEXAMATIC 1888" or equivalent
    (for TASA made):
    ATF "DEXRON 3" or equivalent

    HINT:
    If the fluid is hot, check that the fluid level is within the HOT range on the oil reservoir. If the fluid is cold, check that the fluid level is within the COLD range.

  1. Start the engine and run it at idle.

  1. Turn the steering wheel to the left or right full lock position, and then turn the wheel to the opposite full lock position. Repeat this several times to raise fluid temperature.

    Standard fluid temperature:
    75 to 80°C (167 to 176°F)



    F040897E02
  1. Check for foaming or emulsification. If foaming or emulsification is identified, bleed air from the power steering system.



    R011786E01
  1. With the engine idling, measure the fluid level in the oil reservoir.

  1. Stop the engine.

  1. Wait a few minutes and remeasure the fluid level in the oil reservoir.

    Maximum fluid level increase:
    5 mm (0.20 in.)

    If a problem is found, bleed air from the power steering system.

  1. Check the fluid level.



79. PERFORM REGISTRATION
  1. Perform registration of the injector compensation codes (w/EGR Cooler: Click here, w/o EGR Cooler Click here).

  1. Perform pilot quantity learning (w/EGR Cooler: Click here, w/o EGR Cooler: Click here).



80. INSPECT FOR COOLANT LEAK
  1. Check for engine coolant leaks (Click here).



81. INSPECT FOR OIL LEAK


82. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the problem areas to stop the leak. Replace damaged parts as necessary.


83. INSPECT FOR FUEL LEAK

CAUTION:
  1. During Active Test mode, engine speed becomes high and combustion noise becomes loud, so pay attention.
  2. During Active Test mode, fuel becomes high-pressured. Be extremely careful not to expose your eyes, hands, or body to escaped fuel.

  1. Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.

  1. Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.

  1. Disconnect the return hose from the common rail.

  1. Start the engine and check for fuel leaks from the return pipe.
    If there is fuel leakage, replace the common rail.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and push the intelligent tester main switch on.

  1. Select the Fuel Leak test from the Active Test mode on the intelligent tester.

  1. If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.

  1. Check that there are no leaks from any part of the fuel system.

    NOTICE:
    A return pipe leakage of less than 10 cc (0.6 cu in.) per minute is acceptable.

    If there is fuel leakage, repair or replace parts as necessary.

  1. Reconnect the return hose to the common rail.



84. CHECK ENGINE IDLE SPEED AND MAXIMUM SPEED

HINT:
  1. For more information about the intelligent tester, refer to its operator's manual.
  2. If an intelligent tester is not available, use a tachometer's tester probe as a substitute.



    A098433E01
  1. Connect the intelligent tester to the DLC3.



    A082779E58
  1. If a tester is not available, connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

    SST
    09843-18030  

  1. Inspect the idle speed.

    HINT:
    1. The engine is warmed up.
    2. The A/C switch is OFF.


    1. Start the engine and measure the idle speed.

      Standard idle speed:
      700 to 800 rpm

      If the idle speed is not as specified, perform the troubleshooting procedures in the Diagnostics section.

  1. Inspect the maximum speed.

    1. Start the engine.

    2. Fully depress the accelerator pedal.

    3. Measure the maximum speed.

      Standard maximum speed:
      4,450 to 4,750 rpm

      If the maximum speed is not as specified, perform the troubleshooting in the Diagnostics section.

  1. If the tester probe of the tachometer is connected to the DLC3, disconnect the tester probe with SST from terminal 9 of the DLC3.

  1. Disconnect the intelligent tester from the DLC3.



85. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine, stop the engine and wait for 5 minutes. The oil level should be between the dipstick's low and full level marks.
    If the oil level is low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not add engine oil above the full level mark.



86. INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }



87. INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }