Home › ENGINE ยท 2KD-FTV › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. Remove the 4 bolts and hood.



4. REMOVE NO. 1 ENGINE UNDER COVER


5. REMOVE NO. 2 ENGINE UNDER COVER


6. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



7. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A099591
  1. Drain the coolant by removing the radiator reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug.


    A112147E03


    Text in Illustration 
    *1
    Radiator Reservoir
    *2
    Radiator Reservoir Cap
    *3
    Vent Plug
    *4
    Cylinder Block Drain Cock Plug
    *5
    Radiator Drain Cock Plug
    -
    -



8. DRAIN TRANSMISSION OIL (for Manual Transmission)
  1. Remove the drain plug and gasket to drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



9. DRAIN TRANSMISSION FLUID (for Automatic Transmission)
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }



10. DRAIN POWER STEERING FLUID


11. REMOVE BATTERY CLAMP SUB-ASSEMBLY
  1. Remove the bolt, nut and battery clamp.



12. REMOVE BATTERY


13. REMOVE BATTERY TRAY


14. REMOVE AIR CLEANER ASSEMBLY
  1. Disconnect the mass air flow meter connector.

  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner.



15. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY


    A111789
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the vacuum hose from the gas filter.

  1. Loosen the 2 clamps.

  1. Remove the bolt and disconnect the No. 2 air cleaner pipe together with the 2 air hoses.



16. REMOVE RADIATOR ASSEMBLY
(Click here)


17. REMOVE STARTER ASSEMBLY
  1. for 2.0 kW Type: (Click here)
  2. for 2.7 kW Type: (Click here)


18. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)


19. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(Click here)


20. DISCONNECT HEATER HOSE


    A236415
  1. Disconnect the 2 heater hoses.



21. DISCONNECT PRESSURE FEED TUBE ASSEMBLY


    A236416
  1. Disconnect the oil reservoir to pump hose.



    A236417
  1. Disconnect the pressure feed tube.



22. DISCONNECT FUEL HOSE


    A236418
  1. Disconnect the 2 fuel hoses.



23. DISCONNECT UNION TO CONNECTOR TUBE HOSE


    A236419
  1. Disconnect the union to connector tube hose.



24. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B278058E01
  1. Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
    Text in Illustration 
    *1
    Stopper



    B278059E01
  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
    Text in Illustration 
    *1
    Hinge



25. DISCONNECT WIRE HARNESS


A236420
  1. Remove the upper relay block cover.

  1. Remove the side relay block cover.

  1. Remove the nut and disconnect the engine room junction block wire.

  1. Disconnect the 2 engine room junction block connectors.

  1. Remove the bolt and disconnect the ground cable.



    A233020
  1. Remove the 2 nuts, detach the clamp and disconnect the wire harness.



    A237901
  1. Disconnect the 3 injector driver connectors.



    A272227
  1. for Automatic Transmission:
    Disconnect the 3 TCM connectors.

  1. Disconnect the 4 ECM connectors.



26. DISCONNECT COOLER COMPRESSOR ASSEMBLY
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the cooler compressor. With the hoses connected to the cooler compressor, hang the cooler compressor on the vehicle body with a rope.



27. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
(Click here)


28. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for Automatic Transmission)


29. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)


30. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:
Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.

  1. Remove the 4 bolts and rear No. 1 engine mounting insulator.



31. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)


D029616E03
  1. Place matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.



32. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.



33. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)


    A072851E02
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-58014  
    09330-00021  



    A114803
  1. Remove the 8 bolts and flywheel.



34. REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)


    A072851E02
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-58014  
    09330-00021  



    A114804
  1. Remove the 8 bolts, the rear drive plate spacer, the pump impeller drive plate, and the flywheel.



35. REMOVE REAR END PLATE
  1. Remove the bolt and rear end plate.



36. INSTALL ENGINE HANGERS


    A224109E01
  1. Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    Part No.
    No. 1 engine hanger
    12284-30020
    No. 2 engine hanger
    12282-67030
    Bolt
    90105-T0164 or 91552- 81014 and 90119-T0065 or 91642-81030

    NOTICE:
    Install the engine hangers with new bolts.



37. REMOVE ENGINE ASSEMBLY


    A098988E01
  1. Attach an engine sling device and hang the engine with a chain block.

  1. Remove the 4 bolts and 4 nuts.

  1. Remove the engine by operating the engine sling device and chain block.



38. INSTALL ENGINE TO ENGINE STAND
  1. Install the engine to an engine stand with the bolts.

  1. Remove the 2 bolts and 2 engine hangers.



39. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine.



40. REMOVE FRONT ENGINE MOUNTING INSULATOR


    A233592E03
  1. Remove the 2 nuts and 2 front engine mounting insulators.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side