Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for i-ART)

ECD SYSTEM (for i-ART) > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A206916E06

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM


A279712E02


A279713E02


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
END
B


2.CHECK COMMUNICATION BETWEEN GTS AND ECM
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and GTS on.

  1. Check the communication between the GTS and ECM.

    Result 
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the A22 accelerator pedal position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal position sensor connector.



A
REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY (Click here)
B


4.CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the T3 throttle position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle position sensor connector.



A
REPLACE DIESEL THROTTLE BODY ASSEMBLY (Click here)
B


5.CHECK MIL (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
  1. Disconnect the E33 electric EGR control valve assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the electric EGR control valve assembly connector.



A
REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY (Click here)
B


6.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Disconnect the T9 manifold absolute pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the manifold absolute pressure sensor connector.



A
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
B


7.CHECK MIL (NO. 1 INJECTOR ASSEMBLY)
  1. Disconnect the F31 No. 1 injector assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the No. 1 injector assembly connector.



A
REPLACE NO. 1 INJECTOR ASSEMBLY (Click here)
B


8.CHECK MIL (NO. 2 INJECTOR ASSEMBLY)
  1. Disconnect the F32 No. 2 injector assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the No. 2 injector assembly connector.



A
REPLACE NO. 2 INJECTOR ASSEMBLY (Click here)
B


9.CHECK MIL (NO. 3 INJECTOR ASSEMBLY)
  1. Disconnect the F33 No. 3 injector assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the No. 3 injector assembly connector.



A
REPLACE NO. 3 INJECTOR ASSEMBLY (Click here)
B


10.CHECK MIL (NO. 4 INJECTOR ASSEMBLY)
  1. Disconnect the F34 No. 4 injector assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the No. 4 injector assembly connector.



A
REPLACE NO. 4 INJECTOR ASSEMBLY (Click here)
B


11.CHECK MIL (NOZZLE VANE POSITION SENSOR)
  1. Disconnect the T11 nozzle vane position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the nozzle vane position sensor connector.



A
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
B


12.CHECK HARNESS AND CONNECTOR
  1. Disconnect the A22 accelerator pedal position sensor connector.

  1. Disconnect the T3 throttle position sensor connector.

  1. Disconnect the E33 electric EGR control valve assembly connector.

  1. Disconnect the T11 nozzle vane position sensor connector.

  1. Disconnect the T9 manifold absolute pressure sensor connector.

  1. Disconnect the F31 No. 1 injector assembly connector.

  1. Disconnect the F32 No. 2 injector assembly connector.

  1. Disconnect the F33 No. 3 injector assembly connector.

  1. Disconnect the F34 No. 4 injector assembly connector.

  1. Disconnect the E29 ECM connectors.

  1. Disconnect the E30 ECM connectors.

  1. Disconnect the E31 ECM connectors.

  1. Disconnect the E32 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E31-6 (VCPA) - Body ground
    Always
    10 kΩ or higher
    E31-4 (VCP2) - Body ground
    Always
    10 kΩ or higher
    E29-14 (VCVL) - Body ground
    Always
    10 kΩ or higher
    E29-13 (VCEG) - Body ground
    Always
    10 kΩ or higher
    E30-18 (VCPM) - Body ground
    Always
    10 kΩ or higher
    E30-17 (VNVC) - Body ground
    Always
    10 kΩ or higher
    E29-18 (VIJ1) - Body ground
    Always
    10 kΩ or higher
    E29-17 (VIJ2) - Body ground
    Always
    10 kΩ or higher
    E29-16 (VIJ3) - Body ground
    Always
    10 kΩ or higher
    E29-15 (VIJ4) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the throttle position sensor connector.

  1. Reconnect the electric EGR control valve assembly connector.

  1. Reconnect the nozzle vane position sensor connector.

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the No. 1 injector assembly connector.

  1. Reconnect the No. 2 injector assembly connector.

  1. Reconnect the No. 3 injector assembly connector.

  1. Reconnect the No. 4 injector assembly connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)