AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) > Air Conditioning Compressor Magnetic Clutch Circuit |

| 1.READ VALUE USING INTELLIGENT TESTER (A/C SIGNAL) |
Use the Data List to check if the magnet clutch on request signal is functioning properly (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| A/C Signal | Magnet clutch on request signal / ON or OFF | ON: A/C switch on OFF: A/C switch off | Check this item with the engine idling and the blower switch on (LO level). |
|
| ||||
| OK | |
| 2.INSPECT MAGNET CLUTCH RELAY |
![]() |
Remove the magnet clutch relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY) |
![]() |
Disconnect the A44 air conditioning amplifier assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A44-13 (MGC) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| *a | Front view of wire harness connector (to Air Conditioning Amplifier Assembly) |
|
| ||||
| OK | |
| 4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Remove the air conditioning amplifier assembly with its connectors still connected (Click here).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A44-13 (MGC) - Body ground |
| Below 1 V |
| 11 to 14 V |
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
| Result | Proceed to |
| OK (except KUN51L-KKMSY, KUN51L-KKPSY) | A |
| OK (for KUN51L-KKMSY, KUN51L-KKPSY) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 5.INSPECT MAGNET CLUTCH ASSEMBLY |
![]() |
Remove the cooler compressor assembly.
Apply battery voltage to the magnet clutch and check operation of the magnet clutch.
| Measurement Connection | Specified Condition |
| Battery positive (+) → Terminal 1 Battery negative (-) → Ground wire | Magnet clutch engages |
| Result | Proceed to |
| OK | A |
| NG (for 1KD-FTV) | B |
| NG (for 1GR-FE) | C |
|
| ||||
|
| ||||
| A | |
| 6.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH RELAY - COOLER COMPRESSOR ASSEMBLY AND BATTERY) |
Disconnect the A2 compressor connector.
Remove the magnet clutch relay.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M1-5 - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M1-3 - A2-1 | Always | Below 1 Ω |
| M1-3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.INSPECT COOLER COMPRESSOR ASSEMBLY |
![]() |
Remove the cooler compressor assembly (Click here).
Apply battery voltage to the magnet clutch and check operation of the magnet clutch.
| Measurement Connection | Specified Condition |
| Battery positive (+) → Terminal 1 Battery negative (-) → Ground wire | Magnet clutch engages |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (MAGNET CLUTCH RELAY - COOLER COMPRESSOR ASSEMBLY AND BATTERY) |
Disconnect the A2 compressor connector.
Remove the magnet clutch relay.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M1-5 - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| M1-3 - A2-1 | Always | Below 1 Ω |
| M1-3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM) |
Disconnect the A44 air conditioning amplifier assembly connector.
Disconnect the E5*1 or E13*2 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A44-7 (ACT) - E5-19 (ACT) | Always | Below 1 Ω |
| A44-7 (ACT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A44-7 (ACT) - E13-25 (ACT) | Always | Below 1 Ω |
| A44-7 (ACT) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Remove the air conditioning amplifier assembly with its connectors still connected (Click here).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A44-7 (ACT) - Body ground |
| Below 1 V |
| 11 to 14 V |
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
| Result | Proceed to |
| OK | A |
| NG (for 1KD-FTV) | B |
| NG (for 1GR-FE) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ECM) |
Disconnect the A44 air conditioning amplifier assembly connector.
Disconnect the E5*1 or E13*2 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A44-21 (AC1) - E5-18 (AC1) | Always | Below 1 Ω |
| A44-21 (AC1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A44-21 (AC1) - E13-24 (AC1) | Always | Below 1 Ω |
| A44-21 (AC1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 12.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Remove the air conditioning amplifier assembly with its connectors still connected (Click here).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A44-21 (AC1) - Body ground |
| Below 1 V |
| 11 to 14 V |
| *a | Component with harness connected (Air Conditioning Amplifier Assembly) |
| Result | Proceed to |
| NG | A |
| OK (for 1KD-FTV) | B |
| OK (for 1GR-FE) | C |
|
| ||||
|
| ||||
| A | ||
| ||