DTC P0400 Exhaust Gas Recirculation Flow |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Decelerate from a speed of 50 km/h (80 mph) or more (release accelerator pedal for approximately 5 seconds) | When either condition below is met:
|
|
| DTC No. | Data List |
| P0400 |
|


| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0400) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0400 is output | A |
| P0400 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE EGR VALVE CLOSE) |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
Read the MAF value displayed on the tester while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close.
Read the MAF value when the EGR valve is closed using the Active Test function.
| Active Test | Result | Proceed to |
| Activate the EGR Valve Close: Off (Open) to on (Closed) | MAF value does not change | A |
| MAF value changes | B |
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
| Open (55%) |
| 3.0 to 9.0 gm/s |
| Close (0%) | 15 to 22 gm/s |
|
| ||||
| A | |
| 3.CHECK VACUUM HOSES |
Check the vacuum hoses.
|
| ||||
| OK | |
| 4.INSPECT ELECTRIC VACUUM REGULATING VALVE ASSEMBLY |
Inspect the electric vacuum regulating valve assembly (Click here).
|
| ||||
| OK | |
| 5.INSPECT VACUUM SWITCHING VALVE (FOR EGR CUT) |
Inspect the vacuum switching valve (for EGR cut) (Click here).
|
| ||||
| OK | |
| 6.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (EGR VALVE OPERATION) |
Inspect the electric EGR control valve assembly (Click here).
|
| ||||
| OK | |
| 7.CHECK FOR DEPOSIT (EGR PASSAGE) |
Check the deposit conditions in the EGR cooler and the EGR passage.
|
| ||||
|
| ||||
| 8.REPAIR OR REPLACE VACUUM HOSE |
Repair or replace the vacuum hose.
|
| ||||
| 9.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Replace the electric EGR control valve assembly (Click here).
|
| ||||
| 10.REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR CUT) |
Replace the vacuum switching valve (for EGR cut) (Click here).
|
| ||||
| 11.REPAIR OR REPLACE MALFUNCTIONING PARTS |
| NEXT | |
| 12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0400) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine and warm it up.
Move the shift lever to 2nd gear and decelerate from a speed of 50 km/h (31 mph) or more (fully release the accelerator for approximately 5 seconds or more).
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| NEXT | ||
| ||