Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (w/ VSC)

CAN COMMUNICATION SYSTEM (w/ VSC) > Short to B+ in CAN Bus Line

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
  1. Short between CAN bus lines and +B
  2. ECM
  3. Brake actuator assembly (skid control ECU)
  4. Yaw rate sensor assembly
  5. Spiral cable sub-assembly (steering angle sensor)
  6. No. 1 junction connector
  7. No. 2 junction connector
  8. No. 3 junction connector

WIRING DIAGRAM


C247094E01


INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)


    C201374E96
  1. Disconnect the J52 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D3-6 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D3-14 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


4.CONNECT CONNECTOR
  1. Reconnect the J52 No. 3 junction connector.


NEXT


5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)


    C201374E96
  1. Disconnect the J64 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D3-6 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D3-14 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 12
OK


6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)


    C236884E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J64-13 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J64-7 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 8
OK


7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)


    C236884E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J64-12 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J64-6 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 10
OK

REPLACE NO. 1 JUNCTION CONNECTOR 

8.CONNECT CONNECTOR
  1. Reconnect the J64 No. 1 junction connector.


NEXT


9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)


    C236885E05
  1. Disconnect the S25 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S25-25 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    S25-14 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)  

10.CONNECT CONNECTOR
  1. Reconnect the J64 No. 1 junction connector.


NEXT


11.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)


  1. Disconnect the E13*1 or E5*2 ECM connector.

    1. *1: for 1GR-FE
    2. *2: for 1KD-FTV

    C247212E01


    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for 1KD-FTV
    *a
    Front view of wire harness connector
    (to ECM)
    *b
    Front view of DLC3

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE 
    Tester Connection
    Switch Condition
    Specified Condition
    E13-33 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E13-34 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    for 1KD-FTV 
    Tester Connection
    Switch Condition
    Specified Condition
    E5-24 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E5-23 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for 1GR-FE)
    A
    OK (for 1KD-FTV)
    B
    NG
    C



B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)  

12.CONNECT CONNECTOR
  1. Reconnect the J64 No. 1 junction connector.


NEXT


13.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)


    C236681E67
  1. Disconnect the J65 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J65-5 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J65-16 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)


    C201374E96
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D3-6 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    D3-14 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 18
OK


15.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)


    C236681E66
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J65-7 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J65-18 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 16
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

16.CONNECT CONNECTOR
  1. Reconnect the J65 No. 2 junction connector.


NEXT


17.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (YAW RATE SENSOR ASSEMBLY)


    C236888E05
  1. Disconnect the Y1 yaw rate sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Y1-3 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    Y1-2 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate Sensor Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE YAW RATE SENSOR ASSEMBLY (Click here)  

18.CONNECT CONNECTOR
  1. Reconnect the J65 No. 2 junction connector.


NEXT


19.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C236883E15
  1. Disconnect the J53 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J53-2 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J53-1 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    C236883E14
  1. Disconnect the J63 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J63-2 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    J63-1 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 21
OK

REPLACE NO. 3 JUNCTION CONNECTOR 

21.CONNECT CONNECTOR
  1. Reconnect the J53 and J63 No. 3 junction connectors.


NEXT


22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR)


    C236889E05
  1. Disconnect the S31 spiral cable sub-assembly (steering angle sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    S31-4 (CANH) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    S31-3 (CANL) - D3-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Spiral Cable Sub-assembly [Steering Angle Sensor])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (Click here)