Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM33K0E _54 Brake _043533 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0222679 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1273  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1403  Rear Speed Sensor RH Malfunction  C1404  Rear Speed Sensor LH Malfunction  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.

Skid control rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C223506C01
1.458,1 0.708,0.5 false 0.552,0.396 0.771,0.625 0.219,0.229 10 false *1 4.281,1.854 4.531,2.198 0.25,0.344 10 false *b 6.052,1.156 6.51,1.427 0.458,0.271 10 false 1.4 V 6.052,1.49 6.542,1.813 0.49,0.323 10 false 0.7 V 1.438,2.146 1.656,2.375 0.219,0.229 10 false *2 3.292,0.688 3.51,0.917 0.219,0.229 10 false *a 5.177,1.854 5.365,2.146 0.188,0.292 10 false *c
*1 Speed Sensor *2 Skid Control Rotor
*a Waveform (Reference):
Between Speed Sensor (-) and Body Ground
*b Low speed
*c High speed - -


DTC No. Detection Item DTC Detection Condition Trouble Area
C1273 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor RH

·

Rear skid control rotor RH (Rear axle shaft bearing RH)

·

Sensor installation


C1274 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor LH

·

Rear skid control rotor LH (Rear axle shaft bearing LH)

·

Sensor installation


C1403 Rear Speed Sensor RH Malfunction Either of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of less than 10 km/h (6 mph), the outputs from both rear speed sensors are 0 km/h (0 mph) for a cumulative time of 200 seconds.


·

Rear speed sensor RH

·

Rear skid control rotor RH (Rear axle shaft bearing RH)

·

Sensor installation


C1404 Rear Speed Sensor LH Malfunction Either of the following is detected:
1.

At a vehicle speed of 10 km/h (6 mph) or more, output voltage from one of the speed sensors is less than that from the other sensors for 15 seconds or more.

2.

At a vehicle speed less than 10 km/h (6 mph), output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.

3.

At a vehicle speed of less than 10 km/h (6 mph), the outputs from both rear speed sensors are 0 km/h (0 mph) for a cumulative time of 200 seconds.


·

Rear speed sensor LH

·

Rear skid control rotor LH (Rear axle shaft bearing LH)

·

Sensor installation



PROCEDURE

1.CHECK REAR SPEED SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.
C168336C14
1.994,1.633 2.181,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b
*a Normal
*b Abnormal
*c Clearance


Check the rear speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>INSTALLATION

OK:

There is no clearance between the sensor and the rear axle housing.

The installation bolt is tightened properly.



Result:
Proceed to
OK
NG



OK

2.INSPECT REAR SPEED SENSOR TIP

NG

2.INSPECT REAR SPEED SENSOR TIP

b.

Check the speed sensor tip.


OK:

No scratches, oil, or foreign matter on the sensor tip.


NOTICE:
·

If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign material before replacing the sensor.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

3.INSPECT REAR AXLE SHAFT BEARING

NG

CLEAN OR REPLACE REAR SPEED SENSOR

3.INSPECT REAR AXLE SHAFT BEARING

b.

Check the rear skid control rotor.


OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:
·

The rear skid control rotor is incorporated into the rear axle shaft bearing.

·

If the rear skid control rotor needs to be replaced, replace it together with the rear axle shaft bearing.



c.

Reinstall the rear axle shaft bearing.

for the rear speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>INSTALLATION

for the rear axle shaft bearing (for Rear Disc Brake): Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT(for Rear Disc Brake)>REASSEMBLY

for the rear axle shaft bearing (for Rear Drum Brake): Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT(for Rear Drum Brake)>REASSEMBLY


Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

CLEAN OR REPLACE REAR AXLE SHAFT BEARING

4.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4
f.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

5.REPLACE REAR SPEED SENSOR
5.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.



NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


e.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTCs C1403 and C1404 are not output
DTCs C1403 and/or C1404 are output


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:
·

The rear skid control rotor is incorporated into the rear axle shaft bearing.

·

If the rear skid control rotor needs to be replaced, replace it together with the rear axle shaft bearing.





DTCs C1403 and C1404 are not output

END

DTCs C1403 and/or C1404 are output