When the electrical key transmitter sub-assembly is in the vehicle and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P or N*1 and the brake pedal*1 or clutch pedal*2 is depressed, the engine can be started by pressing the engine switch.
*1: for Automatic Transmission
*2: for Manual Transmission
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Engine does not start | Power Source Control
·
Stop Light Switch1* ·
Steering Unlock Switch ·
Power Supply Condition ·
IG Relay Monitor(Inside) ·
IG Relay Monitor(Outside) ·
Latch Circuit ·
Shift P Signal* ·
Neutral SW/ Clutch SW ·
Starter Request Signal Entry&Start
·
L Code Check ·
Engine Start Request ·
Immobiliser Starting Control
·
Ignition ·
Starter SW ·
Shift Position P or N* |
- |
*: for Automatic Transmission
If the brake pedal*1 or clutch pedal*2 is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal*1 or clutch pedal*2 to illuminate the stop lights increases.
*1: for Automatic Transmission
*2: for Manual Transmission
Refer to "SYSTEM DIAGRAM".
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting.
Before replacing the certification ECU (smart key ECU assembly), electrical key transmitter sub-assembly or steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Entry Function) precaution.
Inspect the fuses of circuits related to this system before performing the following procedure.
If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.
After completing repairs, confirm that the problem does not occur.
When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode changes to on (IG).
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.
If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.
| Tester Display |
|---|
| Operation History |
| Parameter Name | Content |
|---|---|
| Operating Engine Switch / Key RF Signal Interference | When the engine switch was operated, the electrical key transmitter sub-assembly could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high. |
| Parameter Name | Content |
|---|---|
| Operating Power Switch/brake or clutch no signal | When the engine switch was turned on (IG) twice, there was no brake signal, and then the warning alarm sounded. |
| Parameter Name | Content |
|---|---|
| Operating Power Switch/brake or clutch no signal | When the engine switch was turned on (IG) twice, there was no clutch signal, and then the warning alarm sounded. |
| Parameter Name | Content |
|---|---|
| Operating Power Switch/ Indoor oscillator LF Signal Interference | When the engine switch was operated, the room oscillator could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high. |
| Brake or Clutch Switch/Indoor oscillator LF Signal Interference | When the brake switch was operated, the room oscillator could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high. |
| Parameter Name | Content |
|---|---|
| Operating Power Switch/ Indoor oscillator LF Signal Interference | When the engine switch was operated, the room oscillator could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high. |
| Brake or Clutch Switch/Indoor oscillator LF Signal Interference | When the clutch switch was operated, the room oscillator could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high. |
| Parameter Name | Content |
|---|---|
| Operating Power Switch/steering lock detection | Engine did not start because steering is lock status when engine switch was pushed. |
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly near the engine switch, depressing the brake pedal and pressing the engine switch.
| Result | Proceed to |
|---|---|
| Transmitter LED illuminates 3 times or more when switch is pressed and held | A |
| Transmitter LED does not illuminate when switch is pressed and held | B |
| Transmitter LED illuminates once or twice but not a third time | C |
A
B
C
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Key Low Battery | Transmitter battery depleted | Yes or No | Yes: Transmitter battery depleted
No: Transmitter battery not depleted |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new). |
| Tester Display |
|---|
| Key Low Battery |
"No" is displayed in the Data List.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Smart entry and start system (for Start Function) DTCs are output | B |
A
B
Get into the vehicle while carrying the electrical key transmitter.
for Automatic Transmission
Move the shift lever to P.
Depress the brake pedal*1 or clutch pedal*2.
*1: for Automatic Transmission
*2: for Manual Transmission
Press the engine switch and check that the engine cranks.
| Result | Proceed to |
|---|---|
| Engine cranks, but there is no initial combustion or engine is difficult to start | A |
| Engine does not cranks | B |
A
B
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
for Automatic Transmission
Move the shift lever to P.
With the brake pedal*1 or clutch pedal*2 released, check that pressing the engine switch causes the power source mode to change.
*1: for Automatic Transmission
*2: for Manual Transmission
| Result | Proceed to |
|---|---|
| Off → on (ACC) → on (IG) → off | A |
| Power source mode does not change to on (ACC) and on (IG) | B |
| Power source mode changes to on (IG) but not to on (ACC) | C |
| Power source mode changes to on (ACC) but not to on (IG) | D |
A
B
C
D
for Automatic Transmission
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Switch1 | State of brake pedal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
·
Use this item to determine whether the stop light switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". ·
When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time. |
| Tester Display |
|---|
| Stop Light Switch1 |
The item in the Data List changes when the brake pedal is depressed and released.
for Manual Transmission
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | State of clutch pedal | ON or OFF | ON: Clutch pedal depressed
OFF: Clutch pedal released |
·
Use this item to help determine if the clutch position switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
The item in the Data List changes when the clutch pedal is depressed and released.
| Proceed to |
|---|
| OK (for Automatic Transmission) |
| OK (for Manual Transmission) |
| NG (for Automatic Transmission) |
| NG (for Manual Transmission) |
OK (for Automatic Transmission)
OK (for Manual Transmission)
NG (for Automatic Transmission)
NG (for Manual Transmission)
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | Shift position (P and N) | ON or OFF | ON: Shift lever in P or N
OFF: Shift lever not in P or N |
·
Use this item to determine whether the park/neutral start switch assembly is malfunctioning. ·
When the engine cannot be started due to a park/neutral start switch assembly malfunction, "OFF" is displayed. |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift Position P or N | Park/neutral position switch status | ON or OFF | ON: Shift lever in P or N
OFF: Shift lever in any position other than P or N |
When malfunctioning, the engine will not crank. |
| Tester Display |
|---|
| Shift Position P or N |
The item in the Data List changes according to the shift position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter Request Signal | Engine start request signal status | ON or OFF | for Automatic Transmission
ON: With the shift lever in P and the brake pedal depressed, the engine switch is pressed and held OFF: After approximately 1 second has elapsed, the engine switch is released for Manual Transmission
ON: With the clutch pedal depressed, the engine switch is pressed and held OFF: After approximately 1 second has elapsed, the engine switch is released |
·
When the engine cannot be started due to a start request signal malfunction, OFF is displayed. ·
When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time. |
| Tester Display |
|---|
| Starter Request Signal |
Check that the smart warning light is illuminated in green on the combination meter assembly, and then press the engine switch.
The display changes in response to the operation of the engine switch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Starting Control / Data List.
Get into the vehicle while carrying the electrical key transmitter sub-assembly, move the shift lever to P*1, press the engine switch while depressing the brake pedal*1 or clutch pedal*2 and confirm that the Data List item changes.
*1: for Automatic Transmission
*2: for Manual Transmission
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter SW | Starter operation request | ON or OFF | ON: Starter operation requested
OFF: Starter operation not requested |
When malfunctioning, the engine will not crank. |
| Tester Display |
|---|
| Starter SW |
The Data List item changes.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Starting Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter Relay | Starter relay voltage monitor | ON or OFF | ON: ST NO. 1 relay on
OFF: ST NO. 1 relay off |
OFF is displayed when the engine cannot crank. |
| Tester Display |
|---|
| Starter Relay |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Press the engine switch and check that the engine starts.
Engine starts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the park/neutral position switch assembly.
for AC60F: Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for A750F: Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for AC60E: Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Inspect the park/neutral position switch assembly.
for AC60F: Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for A750F: Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for AC60E: Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for AC60F: Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for A750F: Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
for AC60E: Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the C22 park/neutral position switch assembly connector.
Disconnect the C120*1, C15*2, G130*3 or G49*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1KD-FTV
*4: for 1GD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-16 (STAR) - C22-4 (B) | Always | Below 1 Ω |
| G17-16 (STAR) or C22-4 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay.
Inspect the ST NO. 1 relay.
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE STARTING>RELAY>ON-VEHICLE INSPECTION
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE STARTING>RELAY>ON-VEHICLE INSPECTION
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV STARTING>RELAY>ON-VEHICLE INSPECTION
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly)) |
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the C120 and G159*1, C15*2, G130*3 or G49*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1KD-FTV
*4: for 1GD-FTV
for Automatic Transmission
Move the shift lever to P or N.
for Manual Transmission
Clutch pedal depressed.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-16 (STAR) - Body ground | 20°C (68°F) | 93.75 to 136.36 Ω |
| G17-37 (STA) - Body ground |
| Proceed to |
|---|
| OK |
| NG (for Automatic Transmission) |
| NG (for Manual Transmission) |
OK
NG (for Automatic Transmission)
NG (for Manual Transmission)
Remove the starter assembly.
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE STARTING>STARTER>REMOVAL
for 2TR-FE (for DENSO Made): Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(for DENSO Made)>REMOVAL
for 2TR-FE (for BOSCH Made): Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(for BOSCH Made)>REMOVAL
for 1KD-FTV (for DENSO Made): Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for DENSO Made)>REMOVAL
for 1KD-FTV (for BOSCH Made): Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
for 1GD-FTV (for DENSO Made): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for DENSO Made)>REMOVAL
for 1GD-FTV (for BOSCH Made): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
Inspect the starter assembly.
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE STARTING>STARTER>INSPECTION
for 2TR-FE (for DENSO Made): Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(for DENSO Made)>INSPECTION
for 2TR-FE (for BOSCH Made): Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(for BOSCH Made)>INSPECTION
for 1KD-FTV (for DENSO Made): Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for DENSO Made)>INSPECTION
for 1KD-FTV (for BOSCH Made): Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for BOSCH Made)>INSPECTION
for 1GD-FTV (for DENSO Made): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for DENSO Made)>INSPECTION
for 1GD-FTV (for BOSCH Made): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for BOSCH Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE STARTING>STARTER>REMOVAL
for 2TR-FE (for DENSO Made): Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(for DENSO Made)>REMOVAL
for 2TR-FE (for BOSCH Made): Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(for BOSCH Made)>REMOVAL
for 1KD-FTV (for DENSO Made): Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for DENSO Made)>REMOVAL
for 1KD-FTV (for BOSCH Made): Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
for 1GD-FTV (for DENSO Made): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for DENSO Made)>REMOVAL
for 1GD-FTV (for BOSCH Made): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
Remove the starter assembly from the vehicle to perform an inspection.
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE STARTING>STARTER>REMOVAL
for 2TR-FE (for DENSO Made): Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(for DENSO Made)>REMOVAL
for 2TR-FE (for BOSCH Made): Click hereEngine / Hybrid System>2TR-FE STARTING>STARTER(for BOSCH Made)>REMOVAL
for 1KD-FTV (for DENSO Made): Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for DENSO Made)>REMOVAL
for 1KD-FTV (for BOSCH Made): Click hereEngine / Hybrid System>1KD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
for 1GD-FTV (for DENSO Made): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for DENSO Made)>REMOVAL
for 1GD-FTV (for BOSCH Made): Click hereEngine / Hybrid System>1GD-FTV STARTING>STARTER(for BOSCH Made)>REMOVAL
Remove the ST NO. 1 relay.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D3-1 (B) - Body ground | Always | 11 to 14 V |
| ST NO. 1 relay terminal 5 - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 3 - C26-1 (ST) | Always | Below 1 Ω |
| ST NO. 1 relay terminal 3 or C26-1 (ST) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the transmitter battery.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Smart Entry and Start System)>INSPECTION
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Disconnect the G159*1, G57*2, G130*3 or G50*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1KD-FTV
*4: for 1GD-FTV
Disconnect the A4 skid control ECU (brake actuator assembly) connector.
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Disconnect the A64 stop light switch assembly connector.
Disconnect the I4 shift lock control ECU (transmission floor shift assembly) connector.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-7 (B) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-11 (STP1) - A64-3 (L) | Always | Below 1 Ω |
| G16-11 (STP1) or A64-3 (L) - Body ground | Always | 10 kΩ or higher |
| A64-2 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the C22 park/neutral position switch connector.
Disconnect the G120*1, C15*2, G130*3 or G49*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1KD-FTV
*4: for 1GD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-16 (STAR) - C22-4 (B) | Always | Below 1 Ω |
| G17-16 (STAR) or C22-4 (B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C22 park/neutral position switch connector.
Remove the ST NO. 1 relay.
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the G159*1, C15*2, G130*3 or G49*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1KD-FTV
*4: for 1GD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-5 (L) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| C22-5 (L) or ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Remove the ST NO. 1 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-37 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| G17-37 (STA) or ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Press the engine switch and check that the engine starts.
Engine starts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the clutch start switch assembly.
Inspect the clutch start switch assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the B2 clutch start switch assembly connector.
Disconnect the G120*1, C15*2, G130*3 or G49*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1KD-FTV
*4: for 1GD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-16 (STAR) - B2-2 | Always | Below 1 Ω |
| G17-16 (STAR) or B2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the B2 clutch start switch assembly connector.
Disconnect the G120*1, C15*2, G130*3 or G49*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1KD-FTV
*4: for 1GD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-16 (STAR) - B2-2 | Always | Below 1 Ω |
| G17-16 (STAR) or B2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B2 clutch start switch assembly connector.
Remove the ST NO. 1 relay.
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the G159*1, C15*2, G130*3 or G49*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1KD-FTV
*4: for 1GD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B2-1 - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| B2-1 or ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Remove the ST NO. 1 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-37 (STA) - ST NO. 1 relay terminal 2 | Always | Below 1 Ω |
| G17-37 (STA) or ST NO. 1 relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST NO. 1 relay terminal 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Press the engine switch and check that the engine starts.
Engine starts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the steering unlocks when the engine switch is turned on (ACC).
The steering unlocks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying an electrical key transmitter sub-assembly.
for Automatic Transmission
Move the shift lever to P.
Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
*1: for Automatic Transmission
*2: for Manual Transmission
It is determined that the immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
Security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).
| Proceed to |
|---|
| OK |
| NG |
OK
NG