The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the cylinder head gasket removal/installation are shown below.
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
No. 3 injection pipe sub-assembly ·
No. 4 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing Gear Case Assembly |
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.DRAIN ENGINE OIL
17111
4.REMOVE INTAKE MANIFOLD
19850
5.REMOVE GLOW PLUG ASSEMBLY
23670
6.REMOVE INJECTOR ASSEMBLY
23810A
7.REMOVE COMMON RAIL ASSEMBLY
8.REMOVE EXHAUST MANIFOLD WITH TURBOCHARGER
16711
9.REMOVE FAN SHROUD
88320
10.DISCONNECT COOLER COMPRESSOR ASSEMBLY
88431
11.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
11322A
12.REMOVE NO. 1 TIMING BELT COVER
13568
13.REMOVE TIMING BELT
13505
14.REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
13523P
15.REMOVE CAMSHAFT TIMING PULLEY
Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.
Make sure to remove the bolt of the camshaft timing pulley with the timing belt not installed.
Remove the camshaft timing pulley from the intake camshaft sub-assembly.
11322B
16.REMOVE NO. 2 TIMING BELT COVER
Remove the 4 bolts, nut and No. 2 timing belt cover from the cylinder head sub-assembly and timing gear cover.
17.REMOVE CAMSHAFT SUB-ASSEMBLY
13751
18.REMOVE VALVE LIFTER
11101
19.REMOVE CYLINDER HEAD SUB-ASSEMBLY
Uniformly loosen the 18 cylinder head set bolts in several passes in the sequence shown in the illustration. Then remove the 18 cylinder head set bolts and 18 washers.
Cylinder head warpage or cracking could result from removing bolts in the incorrect order.
Lift the cylinder head sub-assembly from the dowels on the cylinder block sub-assembly, and place the cylinder head sub-assembly on wooden blocks on a bench.
Be careful not to damage the contact surfaces of the cylinder head sub-assembly and cylinder block sub-assembly.
If the cylinder head sub-assembly is difficult to lift, use a screwdriver to pry between the cylinder head sub-assembly and cylinder block sub-assembly.
11115
20.REMOVE CYLINDER HEAD GASKET