Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM33K0E _59 Vehicle Exterior _043558 WINDOW / GLASS _0229938 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  INSTALLATION  


PROCEDURE

Hide 68131 1.CLEAN BACK DOOR GLASS

a.
B106929

When reusing the back door glass:

Using a scraper, remove the spacers, clips, moulding, adhesive and double-sided tape on the back door glass.

NOTICE:

Do not damage the back door glass.



b.

Clean the outer edges of the back door glass with non-residue solvent.

NOTICE:

Even if using a new back door glass, clean it with non-residue solvent.



Hide 64828 2.INSTALL BACK WINDOW GLASS CLIP LH

a.

Apply Primer G to the back window glass clip LH installation area on the back door glass.

NOTICE:

Do not apply too much Primer G.



b.

Remove the peeling paper and install a new back window glass clip LH.


c.
B409228C01
2.177,1.521 1.615,1.271 1.615,1.271 1.521,0.885 false 1.917,0.594 2.156,0.531 false 2.365,1.01 2.49,1.167 2.49,1.167 2.365,1.344 false 1.833,0.677 1.688,0.635 false 1.49,0.552 1.802,0.708 0.313,0.156 10 false *1 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 2.208,0.49 2.521,0.646 0.313,0.156 10 false *b 1.458,1.229 1.771,1.427 0.313,0.198 10 false *b 2.531,1.094 2.844,1.292 0.313,0.198 10 false *b
*1 Back Window Glass Clip LH
*a Back Side of Back Door Glass
*b Ceramic Notch


Install the back window glass clip LH to the back door glass in the location shown in the illustration.

NOTICE:

Install the back window glass clip LH after Primer G has been allowed to dry (approximately 3 minuts).



Hide 64827A 3.INSTALL BACK WINDOW GLASS CLIP RH

HINT:

Use the same procedure as for the back window glass clip LH.


Hide 64819 4.INSTALL NO. 2 BACK WINDOW GLASS SPACER

a.

Apply Primer G to the No. 2 back window glass spacer installation area on the back door glass.

NOTICE:

Do not apply too much Primer G.



b.

Remove the peeling paper and install a new No. 2 back window glass spacer.


c.
B409229C01
1.979,0.615 2.083,0.469 false 1.708,0.604 1.583,1.115 1.583,1.115 1.792,1.469 false 2.313,0.604 2.5,0.958 2.5,0.958 2.302,1.25 false 2.052,1.479 2.271,1.458 false 2.115,0.385 2.427,0.542 0.313,0.156 10 false *1 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 1.385,1.021 1.698,1.177 0.313,0.156 10 false *b 2.542,0.896 2.854,1.094 0.313,0.198 10 false *b 2.313,1.365 2.625,1.563 0.313,0.198 10 false *b
*1 No. 2 Back Window Glass Spacer
*a Back Side of Back Door Glass
*b Ceramic Notch


Install the No. 2 back window glass spacer to the back door glass in the location shown in the illustration.

NOTICE:

Install the No. 2 back window glass spacer after Primer G has been allowed to dry (approximately 3 minuts).



Hide 64818B 5.INSTALL NO. 1 BACK WINDOW GLASS SPACER

HINT:

Use the same procedure as for the No. 2 back window glass spacer.


Hide 62785F 6.INSTALL BACK DOOR GLASS SPACER

a.

Apply Primer G to the back spacer installation area of the back door glass.

NOTICE:

Do not apply too much Primer G.



b.

Remove the peeling paper and install a new back door glass spacer.


c.
B409222C01
1.281,1.031 1.354,1.396 1.354,1.396 1.542,1.396 false 1.615,0.969 1.792,0.719 false 1.844,0.604 2.156,0.76 0.313,0.156 10 false *1 0.094,0.052 0.406,0.208 0.313,0.156 10 false *a 1.615,1.323 1.927,1.479 0.313,0.156 10 false *b
*1 Back Door Glass Spacer
*a Back Side of Back Door Glass
*b Ceramic Notch


Install the back door glass spacer to the back door glass in the location shown in the illustration.

NOTICE:

Install the back door glass spacer after Primer G has been allowed to dry (approximately 3 minuts).



Hide 75571F 7.INSTALL BACK DOOR WINDOW MOULDING LH

a.

Apply Primer G to the back door window moulding LH installation area of the back door glass.

NOTICE:

Do not apply too much Primer G.


B415224C02
0.125,0.115 0.438,0.271 0.313,0.156 10 false *a 2.542,0.729 2.698,0.927 0.156,0.198 10 false A 3.177,0.875 3.333,1.073 0.156,0.198 10 true A 3.042,1.906 3.813,2.104 0.771,0.198 10 false A - A 4.729,1.938 5.5,2.135 0.771,0.198 10 false B - B 3.406,2.208 3.563,2.406 0.156,0.198 10 false a 5.073,2.24 5.229,2.438 0.156,0.198 10 false b 1.073,2.042 1.229,2.24 0.156,0.198 10 false B 1.667,1.677 1.823,1.875 0.156,0.198 10 false B
*a Back Side of Back Door Glass - -


Standard:
Area Measurement
a 11.0 mm (0.433 in.)
b 20.2 mm (0.795 in.)



b.

Remove the peeling paper and install a new back door window moulding LH.


c.

Install the back door window moulding LH to the back door glass in the location shown in the illustration.

NOTICE:

Install the back door window moulding LH after Primer G has been allowed to dry (approximately 3 minuts).


B415225C01
0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 2.583,0.74 2.74,0.896 0.156,0.156 10 false A 3.063,0.802 3.219,1 0.156,0.198 10 true A 0.875,2.125 1.031,2.323 0.156,0.198 10 true B 1.615,1.708 1.771,1.906 0.156,0.198 10 false B 3.031,2.063 3.802,2.26 0.771,0.198 10 false A - A 4.875,2.073 5.646,2.271 0.771,0.198 10 false B - B 3.469,3.323 3.625,3.521 0.156,0.198 10 false a 5.625,3.333 5.781,3.531 0.156,0.198 10 false b
*a Back Side of Back Door Glass - -


Standard:
Area Measurement
a 8.0 mm (0.315 in.)
b 20.2 mm (0.795 in.)



Hide 75571F 8.INSTALL BACK DOOR WINDOW MOULDING RH

HINT:

Use the same procedure as for the back door window moulding LH.


Hide 75813C 9.INSTALL BACK DOOR OUTSIDE MOULDING CLIP

a.

Apply Primer G to the back door outside moulding clip installation area of the back door glass.

NOTICE:

Do not apply too much Primer G.


B415220C01
3.438,2.781 3.708,2.635 false 0.094,0.125 0.406,0.323 0.313,0.198 10 false *a 3.833,1.396 3.99,1.594 0.156,0.198 10 true A 3.844,1.771 4,1.969 0.156,0.198 10 true A 5.323,2.083 6.094,2.281 0.771,0.198 10 false A - A 3.75,2.542 4.063,2.74 0.313,0.198 10 false *b
*a Back Side of Back Door Glass *b Ceramic Line
V100155

Primer G - -



b.

Apply adhesive to the location shown in the illustration and install the back door outside moulding clip to the back door glass in the location shown in the illustration.

B415222C02
3.438,2.385 3.563,2.229 false 3.094,2.677 3.302,2.792 false 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 3.792,1.104 3.948,1.302 0.156,0.198 10 true A 3.813,1.688 3.969,1.885 0.156,0.198 10 false A 1.896,3.167 2.667,3.365 0.771,0.198 10 false A - A 3.531,2.104 3.844,2.302 0.313,0.198 10 false *b 3.365,2.792 3.677,2.99 0.313,0.198 10 false *1
*1 Back Door Outside Moulding Clip - -
*a Back Side of Back Door Glass *b Ceramic Line
V100155

Adhesive - -


NOTICE:

Install the back door outside moulding clip after Primer G has been allowed to dry (approximately 3 minuts).



c.

Using a scraper, remove any excess adhesive or apply as necessary.

NOTICE:

Apply adhesive up to the edge of the windshield glass.



Hide 75813F 10.INSTALL NO. 1 BACK DOOR MOULDING CLIP

a.

Apply Primer G to the No. 1 back door moulding clip installation area of the back door glass.

NOTICE:

Do not apply too much Primer G.


B415221C01
3.729,2.771 3.99,2.646 false 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 4.104,1.344 4.26,1.542 0.156,0.198 10 true A 4.156,1.792 4.313,1.99 0.156,0.198 10 false A 5.438,2.104 6.208,2.302 0.771,0.198 10 false A - A 4.021,2.49 4.333,2.688 0.313,0.198 10 false *b
*a Back Side of Back Door Glass *b Ceramic Line
V100155

Primer G - -



b.

Apply adhesive to the location shown in the illustration and install the 14 No. 1 back door moulding clips to the back door glass in the location shown in the illustration.

B415223C02
2.271,2.583 2.49,2.427 false 5.906,2.583 6.125,2.438 false 2.156,2.854 2.344,2.979 false 5.792,2.833 5.99,3.021 false 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 4.104,1.167 4.26,1.365 0.156,0.198 10 false A 4.104,1.688 4.26,1.885 0.156,0.198 10 true A 1.771,3.313 2.542,3.51 0.771,0.198 10 false A - A 2.542,2.344 2.854,2.542 0.313,0.198 10 false *b 6.167,2.302 6.479,2.5 0.313,0.198 10 false *b 2.417,2.948 2.729,3.146 0.313,0.198 10 false *1 6.021,2.99 6.333,3.188 0.313,0.198 10 false *1
*1 No. 1 Back Door Moulding Clips - -
*a Back Side of Back Door Glass *b Ceramic Line
V100155

Adhesive - -


NOTICE:

Install the No. 1 back door outside moulding clips after Primer G has been allowed to dry (approximately 3 minuts).



c.

Using a scraper, remove any excess adhesive or apply as necessary.

NOTICE:

Apply adhesive up to the edge of the windshield glass.



Hide 75573B 11.INSTALL BACK WINDOW OUTSIDE MOULDING

a.

After the adhesive hardens, attach the claw to install the back window outside moulding.

B409227C01
3.885,2.542 3.604,2.417 true 3.031,2.417 2.76,2.552 true 3.948,2.479 4.26,2.635 0.313,0.156 10 false *a 2.542,2.458 2.792,2.635 0.25,0.177 10 false *a
*a Lower Side - -


HINT:

Attach the lower side of the claw first.



Hide 68131 12.INSTALL BACK DOOR GLASS

a.
B388038C01
0.906,0.656 0.563,0.458 false 2.729,0.646 2.406,0.479 false 2.229,0.385 2.542,0.542 0.313,0.156 10 false *1 0.354,0.396 0.667,0.552 0.313,0.156 10 false *1
*1 Vehicle Body
V100155

Adhesive


Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.



ii.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.




b.

Back door glass preliminary installation procedures.

i.

Install the suction cups to the back door glass.


ii.

Temporarily place the back door glass onto the vehicle body and set it so that the gap between the body and the upper portion and sides of the back door glass is even.


iii.
B409219C01
1.771,0.51 2.188,0.198 false 2.198,0.115 2.51,0.271 0.313,0.156 10 false *a
*a Matchmarks


Place adhesive tape on the back door glass and body panel and use a pen to place matchmarks for installation (when using a new back door glass).

HINT:

When reusing a back door glass, check the position of the matchmarks and make adjustments.



iv.

Remove the back door glass.


v.

Apply Primer M to the exposed panel surface of the back door panel.

NOTICE:
·

Do not apply too much Primer M.

·

Do not apply Primer M to the adhesive.

·

Be careful when applying primer to the panel joints and spot welds.





c.

Apply Primer G to the back door glass in the locations shown in the illustration.

B409230C01
0.49,1.906 1.979,2.635 1.49,0.729 2.281,1.917 3.823,2.656 1.542,0.74 4.063,1.917 6.74,2.667 2.677,0.75 1.448,2.813 3.021,3.542 1.573,0.729 4.073,2.813 6.75,3.552 2.677,0.74 1.219,2.406 0.854,2.25 true 5.552,2.26 5.104,2.427 true 3.063,2.427 3.604,2.531 true 2.198,3.25 2.51,3.094 true 5.781,3.281 5.302,3.448 5.302,3.448 6.01,3.281 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 3.688,0.083 3.844,0.281 0.156,0.198 10 false A 3.698,0.677 3.865,0.875 0.167,0.198 10 true A 0.573,1.958 1.344,2.156 0.771,0.198 10 false A - A 4.219,0.677 4.375,0.875 0.156,0.198 10 false B 4.208,0.125 4.365,0.323 0.156,0.198 10 false B 2.344,1.958 3.115,2.156 0.771,0.198 10 false B - B 5.031,0.792 5.188,0.99 0.156,0.198 10 true C 5.667,0.677 5.823,0.875 0.156,0.198 10 false C 4.135,1.958 4.906,2.156 0.771,0.198 10 false C - C 3.781,1.208 3.938,1.406 0.156,0.198 10 false D 3.792,1.698 3.948,1.896 0.156,0.198 10 false D 1.531,2.875 2.302,3.073 0.771,0.198 10 false D - D 4.125,2.844 4.896,3.042 0.771,0.198 10 false E - E 1.406,0.698 1.563,0.896 0.156,0.198 10 false E 2.063,0.854 2.219,1.052 0.156,0.198 10 true E 2.073,2.844 2.229,3.042 0.156,0.198 10 false a 1.302,2 1.458,2.198 0.156,0.198 10 false a 5.104,2 5.26,2.198 0.156,0.198 10 false a 4.917,2 5.073,2.198 0.156,0.198 10 false a 5.667,2.833 5.823,3.031 0.156,0.198 10 false a 6.063,2.844 6.219,3.042 0.156,0.198 10 false a 5.865,2.844 6.021,3.042 0.156,0.198 10 false b 3.104,2.01 3.26,2.208 0.156,0.198 10 false a 0.677,2.156 0.99,2.354 0.313,0.198 10 false *b 3.635,2.469 3.948,2.667 0.313,0.198 10 false *b 5.583,2.188 5.896,2.385 0.313,0.198 10 false *b 2.573,3 2.885,3.198 0.313,0.198 10 false *b 5.104,3.385 5.417,3.583 0.313,0.198 10 false *b
*a Back Side of Back Door Glass *b Adhesive Application Center Line
V100155

Primer G Application Area - -


Standard:
Area Measurement
a 7.0 mm (0.276 in.)
b 8.0 mm (0.315 in.)


HINT:

If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.


NOTICE:
·

Allow Primer G to dry for 3 minutes or more.

·

Throw away any leftover Primer G.

·

Do not apply too much Primer G.




d.
B214800C94
1.198,0.448 1.406,0.521 true 2.521,0.563 2.917,0.385 true 1.292,1.448 1.385,1.604 0.094,0.156 10 false a 2.948,0.292 3.135,0.49 0.188,0.198 10 false *1 0.583,0.615 0.677,0.771 0.094,0.156 10 false a 1.115,0.875 1.208,1.031 0.094,0.156 10 false b 0.781,1.01 0.875,1.167 0.094,0.156 10 false b 1.458,0.479 1.646,0.677 0.188,0.198 10 false *2
*1 Sealer Gun
*2 Nozzle


Cut off the tip of a cartridge nozzle as shown in the illustration.

Standard:
Area Measurement
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)


Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours


i.

Apply a bead of adhesive to the location shown in the illustration.

NOTICE:

Apply the adhesive after Primer G has been allowed to dry (approximately 3 minuts).




e.

Load a sealer gun with the cartridge.


f.

Apply a bead of adhesive to the location shown in the illustration.

B409231C01
0.531,1.917 2.115,2.677 1.583,0.76 2.271,1.938 3.854,2.677 1.583,0.74 4,1.938 6.563,2.677 2.563,0.74 1.49,2.906 3.177,3.688 1.688,0.781 4.021,2.927 6.583,3.688 2.563,0.76 1.26,2.396 1.625,2.25 true 3.073,2.396 3.448,2.229 true 4.906,2.406 5.365,2.146 true 2.198,3.302 2.594,3.104 true 5.646,3.396 6.177,3.594 6.177,3.594 5.854,3.406 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.542,2.823 0.698,3.021 0.156,0.198 10 false a 1.01,3.188 1.167,3.385 0.156,0.198 10 false b 3.781,0.625 3.938,0.823 0.156,0.198 10 false A 3.792,0.125 3.948,0.323 0.156,0.198 10 false A 4.24,0.146 4.396,0.344 0.156,0.198 10 false B 4.281,0.646 4.438,0.844 0.156,0.198 10 false B 5.042,0.781 5.198,0.979 0.156,0.198 10 true C 5.667,0.698 5.823,0.896 0.156,0.198 10 false C 3.823,1.208 3.979,1.406 0.156,0.198 10 false D 3.865,1.729 4.021,1.927 0.156,0.198 10 false D 1.438,0.583 1.594,0.781 0.156,0.198 10 false E 2.01,0.719 2.167,0.917 0.156,0.198 10 true E 0.625,1.958 1.396,2.156 0.771,0.198 10 false A - A 2.344,1.979 3.115,2.177 0.771,0.198 10 false B - B 4.073,1.99 4.844,2.188 0.771,0.198 10 false C - C 1.542,2.958 2.313,3.156 0.771,0.198 10 false D - D 4.073,2.958 4.844,3.156 0.771,0.198 10 false E - E 1.656,2.156 1.969,2.354 0.313,0.198 10 false *b 3.458,2.115 3.771,2.313 0.313,0.198 10 false *b 5.406,2.031 5.719,2.229 0.313,0.198 10 false *b 2.667,3.01 2.979,3.208 0.313,0.198 10 false *b 6.229,3.521 6.542,3.719 0.313,0.198 10 false *b
*a Back Side of Back Door Glass *b Adhesive Application Center Line
V100155

Adhesive - -


Standard:
Area Measurement
a 8.0 mm (0.315 in.)
b 12.0 mm (0.472 in.)


NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Check that the clips are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and glass.




g.

Install the back door glass.

i.
B409219C01
1.771,0.51 2.188,0.198 false 2.198,0.115 2.51,0.271 0.313,0.156 10 false *a
*a Matchmarks


Using suction cups, position the back door glass so that the matchmarks are aligned and install the back door glass.

NOTICE:

Install the back door glass after Primer M on the back door panel has been allowed to dry (approximately 3 minuts).



ii.

Lightly press the back door glass from outside the vehicle so that it is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.



iii.

Using a scraper, remove any excess adhesive or apply as necessary.

HINT:

Apply adhesive up to the edge of the back door glass.


NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours



iv.

Remove any excess adhesive before it hardens.


v.

Hold the back door glass in place securely with protective tape or equivalent until the adhesive hardens.



h.
B409220C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Attach the clamp and claw.


i.

Connect the connector and install the bolt.


Hide 68131 13.CHECK FOR BACK DOOR GLASS

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


c.

Remove any protective or adhesive tape.


Hide 14.INSTALL REAR SPOILER ASSEMBLY

Hide 64886B 15.INSTALL BACK DOOR GLASS CHANNEL LH

Hide 64885C 16.INSTALL BACK DOOR GLASS CHANNEL RH

HINT:

Use the same procedure as for the LH side.


Hide 85143R 17.INSTALL REAR WIPER MOTOR GROMMET

Hide 85110R 18.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 19.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85292A 20.INSTALL REAR WIPER ARM HEAD CAP

Hide 67847A 21.INSTALL BACK DOOR SERVICE HOLE COVER (w/ Cover)

Hide 67750 22.INSTALL BACK DOOR TRIM BOARD ASSEMBLY

Hide 74811D 23.INSTALL DOOR PULL HANDLE

Hide 67938A 24.INSTALL BACK DOOR SIDE GARNISH LH

Hide 67937B 25.INSTALL BACK DOOR SIDE GARNISH RH

Hide 67939B 26.INSTALL CENTER BACK DOOR GARNISH