Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART)
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P13C3  Fuel Temperature Sensor Circuit Range/Performance #1  P13C8  Fuel Temperature Sensor Circuit Range/Performance #2  P13CD  Fuel Temperature Sensor Circuit Range/Performance #3  P13D3  Fuel Temperature Sensor Circuit Range/Performance #4  


DESCRIPTION

The i-ART injector detects the fuel temperature from the sensors built into each injector assembly.

The fuel temperature detected inside the injector assembly is sent to the ECM as feedback through the communication line.

The ECM determines that there is a malfunction when the difference in the temperature data (voltage value) received from the injector assemblies via INJ communication exceeds a certain value.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P13C3 Fuel Temperature Sensor Circuit Range/Performance #1 The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more.
(1 trip detection logic)
·

VIJ circuit malfunction

·

Fuel temperature sensor (built into injector assembly)

·

Harness or connector


- DTC stored
P13C8 Fuel Temperature Sensor Circuit Range/Performance #2 The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more.
(1 trip detection logic)
·

VIJ circuit malfunction

·

Fuel temperature sensor (built into injector assembly)

·

Harness or connector


- DTC stored
P13CD Fuel Temperature Sensor Circuit Range/Performance #3 The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more.
(1 trip detection logic)
·

VIJ circuit malfunction

·

Fuel temperature sensor (built into injector assembly)

·

Harness or connector


- DTC stored
P13D3 Fuel Temperature Sensor Circuit Range/Performance #4 The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more.
(1 trip detection logic)
·

VIJ circuit malfunction

·

Fuel temperature sensor (built into injector assembly)

·

Harness or connector


- DTC stored

Related Data List
DTC No. Data List
P13C3
P13C8
P13CD
P13D3
·

Fuel Temperature #1

·

Fuel Temperature #2

·

Fuel Temperature #3

·

Fuel Temperature #4



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P13C3
P13C8
P13CD
P13D3
Engine switch on (IG) for 8 second or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

d.

Read the DTCs

Result:
Result Proceed to
"Fuel pressure sensor circuit DTC" and "Injector Internal EEPROM Malfunction circuit DTC" are output*1 A
"Fuel pressure sensor circuit DTC" and "Fuel temperature sensor circuit DTC" are output*2 B
Only DTCs related to the "Fuel temperature sensor circuit DTC" are output*3 C


HINT:
·

*1: Fuel pressure sensor circuit DTC and Injector Internal EEPROM Malfunction circuit DTCs:

Fuel pressure sensor circuit DTC: P13A1, P13A2, P13A3, P13A6, P13A7, P13A8, P13AB, P13AC, P13AD, P13B1, P13B2, P13B3.

Injector Internal EEPROM Malfunction circuit: P168A, P168B, P168C, P168D.

·

*2: Fuel pressure sensor circuit DTC: P13A1, P13A2, P13A3, P13A6, P13A7, P13A8, P13AB, P13AC, P13AD, P13B1, P13B2, P13B3.

Fuel temperature sensor circuit DTC: P13C3, P13C8, P13CD, P13D3.

·

*3: Fuel temperature sensor circuit DTC: P13C3, P13C8, P13CD, P13D3.





A

GO TO INTERNAL EEPROM MALFUNCTION CIRCUIT

B

C

2.CHECK ECM (FUEL TEMPERATURE SENSOR VOLTAGE)
2.CHECK ECM (FUEL TEMPERATURE SENSOR VOLTAGE)
a.

Disconnect the injector assembly connector.


b.
A378120C07
1.813,0.521 2.208,0.792 0.396,0.271 1.26,0.521 1.656,0.792 0.396,0.271 0.573,2.583 1.615,1.635 true 1.948,1.635 2.583,0.594 2.583,0.594 2.708,0.594 true 2.313,2.583 1.906,1.688 true 2.719,0.156 2.635,0.156 2.635,0.156 1.865,1.635 true 1.781,1.688 1.646,3.083 1.646,3.083 1.51,3.083 true 1.823,1.635 1.99,3.073 1.99,3.073 2.135,3.073 true 1.99,1.625 2.5,0.938 2.5,0.938 2.604,0.938 true 1.188,2.583 1.656,1.688 true 1.333,0.583 1.792,0.781 0.458,0.198 10 false C40 1.885,0.594 2.344,0.792 0.458,0.198 10 false C41 0.333,2.594 0.979,2.823 0.646,0.229 10 false 19 (EIJ1) 0.99,2.604 1.635,2.813 0.646,0.208 10 false 28 (VIJ1) 2.115,2.594 2.76,2.802 0.646,0.208 10 false 30 (EIJ2) 2.781,0.083 3.375,0.281 0.594,0.198 10 false 24 (VIJ2) 2.208,2.99 2.854,3.219 0.646,0.229 10 false 25 (EIJ3) 2.75,0.521 3.365,0.74 0.615,0.219 10 false 22 (VIJ4) 0.948,3 1.594,3.208 0.646,0.208 10 false 33 (VIJ3) 2.646,0.865 3.292,1.094 0.646,0.229 10 false 21 (EIJ4) 0.271,0.188 0.729,0.385 0.458,0.198 10 false *a
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C40-28 (VIJ1) - C40-19 (EIJ1) Engine switch on (IG) 4.5 to 5.5 V
C41-24 (VIJ2) - C41-30 (EIJ2) Engine switch on (IG) 4.5 to 5.5 V
C41-33 (VIJ3) - C41-25 (EIJ3) Engine switch on (IG) 4.5 to 5.5 V
C41-22 (VIJ4) - C41-21 (EIJ4) Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)

NG

8.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
a.

Disconnect the injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C133-2 (VIJ1) - C40-28 (VIJ1) Always Below 1 Ω
C133-1 (EIJ1) - C40-19 (EIJ1) Always Below 1 Ω
C134-2 (VIJ2) - C41-24 (VIJ2) Always Below 1 Ω
C134-1 (EIJ2) - C41-30 (EIJ2) Always Below 1 Ω
C135-2 (VIJ3) - C41-33 (VIJ3) Always Below 1 Ω
C135-1 (EIJ3) - C41-25 (EIJ3) Always Below 1 Ω
C136-2 (VIJ4) - C41-22 (VIJ4) Always Below 1 Ω
C136-1 (EIJ4) - C41-21 (EIJ4) Always Below 1 Ω
C133-2 (VIJ1) or C40-28 (VIJ1) - Body ground and other terminals Always 10 kΩ or higher
C133-1 (EIJ1) or C40-19 (EIJ1) - Body ground and other terminals Always 10 kΩ or higher
C134-2 (VIJ2) or C41-24 (VIJ2) - Body ground and other terminals Always 10 kΩ or higher
C134-1 (EIJ2) or C41-30 (EIJ2) - Body ground and other terminals Always 10 kΩ or higher
C135-2 (VIJ3) or C41-33 (VIJ3) - Body ground and other terminals Always 10 kΩ or higher
C135-1 (EIJ3) or C41-25 (EIJ3) - Body ground and other terminals Always 10 kΩ or higher
C136-2 (VIJ4) or C41-22 (VIJ4) - Body ground and other terminals Always 10 kΩ or higher
C136-1 (EIJ4) or C41-21 (EIJ4) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the injector assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
a.

Replace the injector assembly of the cylinder relevant to the DTC.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the engine switch off and wait for at least 30 seconds.


d.

Turn the engine switch on (IG) for 8 seconds or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED