Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT › from 2016.07
RM33K0E _58 Vehicle Interior _043555 HEATING / AIR CONDITIONING _0219879 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front air conditioning unit removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal
w/ Power Back Door System:

Reset back door close position


Power back door system (Click here)

CAUTION:
B410193

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

Hide 1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 88710E 3.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (for 1GD-FTV)

a.
E315746

Remove the bolt and disconnect the air conditioner tube and accessory assembly.


b.

Remove the 2 O-rings from the air conditioner tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 88707 4.DISCONNECT SUCTION PIPE SUB-ASSEMBLY (except 1GD-FTV)

a.
E315745C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the bolt and rotate the hook connector as shown in the illustration.


b.
E315747

Disconnect the suction pipe sub-assembly.


c.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 88710E 5.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (except 1GD-FTV)

a.
E315748

Disconnect the air conditioner tube and accessory assembly.


b.

Remove the O-ring from the air conditioner tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 6.DISCONNECT HEATER WATER OUTLET HOSE

a.
E315749

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose.

NOTICE:
·

Do not apply excessive force to the heater water outlet hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 7.DISCONNECT HEATER WATER INLET HOSE

a.
E315750

Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water inlet hose.

NOTICE:
·

Do not apply excessive force to the heater water inlet hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87128 8.REMOVE HEATER GROMMET

E315751

a.

Detach the claw and remove the heater grommet.


Hide 9.REMOVE FRONT SEAT ASSEMBLY LH

Hide 10.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 55303B 11.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 87211 12.REMOVE NO. 1 AIR DUCT

a.
E320358

Remove the bolt.


b.

Detach the claw and remove the No. 1 air duct.

NOTICE:
·

When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.

·

If the No. 1 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.




Hide 87211A 13.REMOVE NO. 2 AIR DUCT

a.
E320359

Detach the claw and remove the No. 2 air duct.

NOTICE:
·

When removing, do not crack or deform the lower heater case of the air conditioning radiator assembly.

·

If the No. 2 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.




Hide 14.REMOVE STEERING COLUMN ASSEMBLY

Hide 67914B 15.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 16.REMOVE COWL SIDE TRIM BOARD LH

Hide 67913B 17.REMOVE FRONT DOOR SCUFF PLATE RH

Hide 62111C 18.REMOVE COWL SIDE TRIM BOARD RH

Hide 67918E 19.REMOVE REAR DOOR SCUFF PLATE LH

Hide 67917C 20.REMOVE REAR DOOR SCUFF PLATE RH

Hide 62414A 21.REMOVE LOWER CENTER PILLAR GARNISH LH

Hide 62413A 22.REMOVE LOWER CENTER PILLAR GARNISH RH

Hide 23.REMOVE FRONT FLOOR CARPET ASSEMBLY

a.

for LHD:

Remove the 5 clips.

E332258C01
1.781,0.823 2.094,1.021 0.313,0.198 10 true *A
*A for LHD - -
V100155

Fastener
V113147

Remove in this Direction



b.

for RHD:

Remove the 4 clips.


c.

Detach each fastener.


d.

Detach the guide and fold back the front floor carpet assembly as shown in the illustration.


Hide 55395C 24.REMOVE NO. 1 INSTRUMENT PANEL INNER BRACKET COVER LH (for LHD)

E323201

a.

Remove the 3 clips and No. 1 instrument panel inner bracket cover LH


Hide 55215D 25.REMOVE NO. 3 DASH PANEL INSULATOR PAD

a.
E325193C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the No. 3 dash panel insulator pad as shown in the illustration.


Hide 55214C 26.REMOVE NO. 2 DASH PANEL INSULATOR PAD

a.
E325194C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the No. 2 dash panel insulator pad as shown in the illustration.


Hide 55306A 27.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E332259C01
0,0 0,0 false
V100135

Nut
V100136

Bolt
V100137

Screw


Detach the clamp.


b.

Remove the nut, bolt, 4 screws and No. 1 instrument panel brace sub-assembly.


Hide 55307C 28.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E332260C01
0,0 0,0 false
V100135

Nut
V100136

Bolt
V100137

Screw


Remove the nut, bolt, 3 screws and No. 2 instrument panel brace sub-assembly.


Hide 82141 29.DISCONNECT INSTRUMENT PANEL WIRE

a.
E332261

for Automatic Air Conditioning System:

i.

Disconnect the connector.


ii.

Detach the clamp.



b.
E332262

for Manual Air Conditioning System:

i.

Disconnect the connector.


ii.

Detach the clamp.



c.

Remove each bolt and each ground wire.

E332263C01
2.438,6.042 2.75,6.198 0.313,0.156 10 true *A 5.042,6.031 5.354,6.188 0.313,0.156 10 true *B 2.927,1.052 3.156,1.229 0.229,0.177 10 true *1 3.219,1.646 3.448,1.823 0.229,0.177 10 true *1 3.813,1.458 4.042,1.635 0.229,0.177 10 true *1 3.875,0.51 4.104,0.688 0.229,0.177 10 true *1 4.333,1.5 4.563,1.677 0.229,0.177 10 true *1 1.583,0.531 1.813,0.708 0.229,0.177 10 true *1 2.438,4.667 2.75,4.823 0.313,0.156 10 true *C
*A for Manual Air Conditioning System *B for Automatic Air Conditioning System
*C w/ PTC Heater - -
*1 Ground Wire - -



d.

Disconnect each connector and detach each clamp.


e.

Remove each bolt, nut and screw, and then disconnect the instrument panel wire.


Hide 55330B 30.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When removing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.
E325411C01
0.073,0.094 0.385,0.25 0.313,0.156 10 true *A
*A for Driver Side
V100155

Protective Tape


Put protective tape around the hole plug.


b.

Using a screwdriver with its tip wrapped with protective tape, remove the 2 hole plugs.


c.

for Automatic Transmission:

Remove the 11 bolts.

E332264C01
1.104,0.927 1.354,1.083 0.25,0.156 10 true *A
*A for Manual Transmission - -
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Bolt D



d.

for Manual Transmission:

Remove the 12 bolts.


Hide 55950G 31.REMOVE DEFROSTER NOZZLE ASSEMBLY

E332265

a.

Detach the claw and remove the defroster nozzle assembly.


Hide 32.REMOVE AIR CONDITIONING UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When disassembling the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

Disconnect the drain cooler hose.

E332266


b.

Remove the nut and air conditioning unit assembly and instrument panel reinforcement assembly.


Hide 87211B 33.REMOVE NO. 3 AIR DUCT

a.
E332267

Detach the claw and remove the No. 3 air duct.