Home › Engine / Hybrid System › 2TR-FBE ENGINE MECHANICAL › ENGINE UNIT › from 2016.07
RM33K0E _51 Engine / Hybrid System _054513 2TR-FBE ENGINE MECHANICAL _0272878 ENGINE UNIT A

2TR-FBE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 16268 1.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install a new gasket and the No. 1 water by-pass pipe with the 2 nuts.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


b.

w/ Oil Cooler:

Connect the No. 4 water by-pass hose to the No. 1 water by-pass pipe, and slide the clip to secure the hose.


Hide 16603 2.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 88431 3.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

NOTICE:

Install the No. 1 compressor mounting bracket exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.


a.
A346840

Temporarily install the No. 1 compressor mounting bracket with the 3 bolts.

HINT:

Temporarily install the No. 1 compressor mounting bracket with the 3 bolts so that the bracket can be moved by hand.



b.
A346841C01
1.219,3.406 1.427,3.604 0.208,0.198 10 false *a 2.115,4.313 2.323,4.51 0.208,0.198 10 false *b 0.729,2.531 0.917,2.729 0.188,0.198 10 false *c 2.969,3.406 3.177,3.604 0.208,0.198 10 false *a 0.5,0.354 0.656,0.552 0.156,0.198 10 true B
*a No Clearance
*b Push
*c Front


Push the No. 1 compressor mounting bracket toward the cylinder block as shown in the illustration and tighten bolt B.

Torque:
for bolt B : 45 N*m (459 kgf*cm, 33 ft.*lbf)

HINT:

Make sure there is no clearance between the cylinder block and No. 1 compressor mounting bracket as shown in the illustration.



c.
A346842C01
2.094,0.104 2.219,0.281 0.125,0.177 10 true 1 2.135,1.583 2.26,1.76 0.125,0.177 10 true 3 2.615,1.229 2.74,1.406 0.125,0.177 10 true 2 0.521,1.427 0.646,1.604 0.125,0.177 10 true 4
V100135

Bolt A
V100136

Bolt C


Uniformly tighten the 4 bolts in the order shown in the illustration.

Torque:
for bolt A : 45 N*m (459 kgf*cm, 33 ft.*lbf)
for bolt C : 24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 88440B 4.INSTALL IDLE PULLEY ASSEMBLY

a.

Temporarily install the idle pulley assembly with the bolt.

NOTICE:

Do not use any tools.



b.

Tighten the bolt.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 25710 8.INSTALL AIR SWITCHING VALVE ASSEMBLY

Hide 17167 10.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 12311 11.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.

Install the front No. 1 engine mounting bracket RH with the 4 bolts.

Torque:
51 N*m (520 kgf*cm, 38 ft.*lbf)


Hide 12315 12.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Install the front No. 1 engine mounting bracket LH with the 4 bolts.

Torque:
51 N*m (520 kgf*cm, 38 ft.*lbf)


Hide 16261G 13.INSTALL NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose to the cylinder head sub-assembly, and slide the clamp to secure the hose.


Hide 14.INSTALL HEATER HOSE

a.

Connect the heater hose to the cylinder head sub-assembly and No. 1 water by-pass pipe, and slide the clamp to secure the hoses.


Hide 15.INSTALL ENGINE WIRE

a.
A346843C01
2.219,1.99 2.417,1.99 2.417,1.99 2.615,1.573 true 2.313,0.844 2.51,1.052 0.198,0.208 10 true *a 2.031,1.906 2.219,2.094 0.188,0.188 10 true *b 1.25,1.146 1.521,1.333 0.271,0.188 10 true 45° 0.594,1.146 0.865,1.333 0.271,0.188 10 true 45° 0.479,0.271 0.615,0.448 0.135,0.177 10 true A 1.875,0.063 2.01,0.24 0.135,0.177 10 true A 0.156,1.969 0.292,2.146 0.135,0.177 10 true B
*a INCORRECT
*b Do not Allow Wires to Overlap


Connect the engine wire (engine ground wire) to the rear side of the engine assembly with the 2 bolts so that it is within the specified range shown in the illustration.

Torque:
for bolt A : 25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Connect the engine wire to the rear side of the engine assembly with the bolt.

Torque:
for bolt B : 30 N*m (306 kgf*cm, 22 ft.*lbf)


c.

Connect the connectors and clamps of the engine wire.


Hide 12229 17.INSTALL PCV PIPE

a.

Install the PCV pipe with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the PCV hose to the PCV valve sub-assembly and intake manifold.


Hide 23250 19.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23250 20.INSTALL FUEL DELIVERY PIPE WITH FUEL INJECTOR

Hide 23270 21.INSTALL FUEL PRESSURE PULSATION DAMPER ASSEMBLY

Hide 22030 22.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY