Home › Engine / Hybrid System › 2TR-FBE LUBRICATION › OIL PUMP › from 2016.07
RM33K0E _51 Engine / Hybrid System _054518 2TR-FBE LUBRICATION _0272892 OIL PUMP A

2TR-FBE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11303A 1.INSTALL TIMING CHAIN CASE OIL SEAL

A336770C01
0.667,1.542 0.813,1.542 0.813,1.542 1.104,1.844 false 0.365,1.479 0.688,1.688 0.323,0.208 10 false SST 3.156,1.646 3.313,1.833 0.156,0.188 10 false *a
*a No Clearance


a.

Using SST and a hammer, tap in a new timing chain case oil seal until its surface is flush with the edge of the timing chain cover sub-assembly.

SST
09223-75010  09950-70010  (09951-07100)

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the timing chain case oil seal at an angle.




b.

Apply MP grease to the lip of the timing chain case oil seal.


Hide 16100 2.INSTALL ENGINE WATER PUMP ASSEMBLY

a.

Install a new gasket and the engine water pump assembly with the 8 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 11302 3.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Install 3 new O-rings to the timing chain cover sub-assembly.


b.

Clean and degrease the contact surfaces of the timing chain cover sub-assembly, cylinder head sub-assembly and cylinder block sub-assembly.


c.

Apply seal packing to the timing chain cover sub-assembly in a continuous line as shown in the following illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


A346226C01
0.698,0.563 0.917,0.563 0.917,0.563 1.198,1.125 true 3.208,1.74 3.458,1.969 3.458,1.969 3.604,1.969 false 4.146,0.813 4.281,0.813 4.281,0.813 4.427,1.031 false 4.188,1.5 4.531,1.5 true 6.406,1.458 6.719,1.458 false 5.156,7.083 5.385,7.083 false 0.552,0.49 0.708,0.688 0.156,0.198 10 false A 2.781,0.896 2.917,1.073 0.135,0.177 10 true C 3.344,0.896 3.5,1.094 0.156,0.198 10 true C 3.646,1.896 3.802,2.094 0.156,0.198 10 true B 4,0.74 4.156,0.938 0.156,0.198 10 true D 4.052,1.427 4.188,1.635 0.135,0.208 10 true K 6.76,1.385 6.917,1.583 0.156,0.198 10 true K 0.469,4.042 0.625,4.24 0.156,0.198 10 false A 2.26,4.01 2.417,4.208 0.156,0.198 10 false B 3.76,4.125 4.052,4.365 0.292,0.24 10 false C-C 5.51,4.104 5.667,4.302 0.156,0.198 10 false D 0.427,5.375 0.781,5.573 0.354,0.198 10 false E-E 2.25,5.365 2.604,5.563 0.354,0.198 10 false G-G 3.813,5.354 3.99,5.552 0.177,0.198 10 false I-I 5.531,5.469 5.781,5.688 0.25,0.219 10 false J-J 0.365,6.594 0.615,6.813 0.25,0.219 10 false F-F 2.229,6.563 2.521,6.781 0.292,0.219 10 false H-H 5.542,6.635 5.688,6.865 0.146,0.229 10 false K 0.563,4.635 0.677,4.833 0.115,0.198 10 true E 1.271,4.583 1.385,4.781 0.115,0.198 10 true E 1.271,4.896 1.385,5.094 0.115,0.198 10 true F 0.635,4.938 0.75,5.135 0.115,0.198 10 true F 2.375,4.219 2.5,4.406 0.125,0.188 10 true G 2.24,4.771 2.375,4.969 0.135,0.198 10 true H 3.167,4.76 3.292,4.958 0.125,0.198 10 true H 5.729,4.875 5.865,5.063 0.135,0.188 10 false J 6.167,4.531 6.281,4.729 0.115,0.198 10 true J 6.208,6.865 6.448,7.052 0.24,0.188 10 false *1 6.208,7.198 6.458,7.375 0.25,0.177 10 false *2 4.083,4.198 4.25,4.375 0.167,0.177 10 false *a 1.073,6.26 1.26,6.469 0.188,0.208 10 false *b 4.229,5.458 4.438,5.656 0.208,0.198 10 false *n 3.646,1.167 3.833,1.354 0.188,0.188 10 false *c 0.24,1.104 0.417,1.313 0.177,0.208 10 false *d 1.115,7.406 1.292,7.625 0.177,0.219 10 false *e 6.104,5.542 6.313,5.75 0.208,0.208 10 false *f 4.229,1.771 4.427,1.969 0.198,0.198 10 false *g 0.271,1.385 0.417,1.573 0.146,0.188 10 false *j 3.635,1.406 3.813,1.625 0.177,0.219 10 false *h 5.219,4.75 5.396,4.958 0.177,0.208 10 false *i 4.115,5.156 4.302,5.344 0.188,0.188 10 false *k 5.479,5.885 5.635,6.083 0.156,0.198 10 false *l 1.01,5.427 1.208,5.615 0.198,0.188 10 false *m 1.021,6.604 1.25,6.802 0.229,0.198 10 false *n 4.948,5.792 5.156,6.042 0.208,0.25 10 false *k 4.958,6.99 5.135,7.24 0.177,0.25 10 false *p 6.573,1.771 6.771,1.969 0.198,0.198 10 false *g 4.635,4.719 4.833,4.906 0.198,0.188 10 false *k 0.365,5.792 0.563,5.979 0.198,0.188 10 false *k 2.667,5.438 2.885,5.625 0.219,0.188 10 false *m 3.396,5.781 3.594,5.969 0.198,0.188 10 false *k 2.656,6.26 2.844,6.469 0.188,0.208 10 false *b 4.177,6.281 4.375,6.469 0.198,0.188 10 false *d 0.344,6.948 0.521,7.146 0.177,0.198 10 false *k 2.698,6.583 2.917,6.792 0.219,0.208 10 false *o 2.635,7.427 2.813,7.635 0.177,0.208 10 false *d 3.427,6.948 3.625,7.135 0.198,0.188 10 false *k 3.042,4.219 3.167,4.406 0.125,0.188 10 true G 2.385,4.458 2.469,4.646 0.083,0.188 10 true I 3.031,4.458 3.146,4.656 0.115,0.198 10 true I 2.99,4.979 3.104,5.177 0.115,0.198 10 true I 2.427,4.979 2.51,5.167 0.083,0.188 10 true I
*1 Cylinder Head Sub-assembly *2 Cylinder Block Sub-assembly
*a 2.0 mm (0.0787 in.) *b 2.5 mm (0.0984 in.)
*c 5.0 mm (0.197 in.) *d 6.0 mm (0.236 in.)
*e 7.0 mm (0.276 in.) *f 8.0 mm (0.315 in.) or more
*g 20 mm (0.787 in.) *h 54 mm (2.13 in.)
*i 56.5 mm (2.22 in.) *j 58 mm (2.28 in.)
*k 2.5 to 4.0 mm (0.0984 to 0.157 in.) *l 5.0 to 6.0 mm (0.197 to 0.236 in.)
*m 9.0 to 13 mm (0.354 to 0.512 in.) *n 10 to 14 mm (0.394 to 0.551 in.)
*o 12 to 16 mm (0.472 to 0.630 in.) *p Seal Packing


NOTICE:
·

Remove any oil from the contact surface.

·

When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.

·

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not start the engine for at least 4 hours after the installation.




d.
A346227

Align the width of the joint portion of the oil pump drive rotor and the crankshaft timing gear, and then install the timing chain cover sub-assembly.


e.

Temporarily install the timing chain cover sub-assembly with the 16 bolts and nut.

A346228C01
0.458,0.073 0.771,0.229 0.313,0.156 10 false *a 3.875,0.073 4.188,0.229 0.313,0.156 10 false *b 0.531,0.458 0.688,0.656 0.156,0.198 10 false A 0.521,0.875 0.677,1.073 0.156,0.198 10 false A 0.521,1.24 0.677,1.438 0.156,0.198 10 false D 0.49,1.552 0.646,1.75 0.156,0.198 10 false A 0.458,2 0.615,2.198 0.156,0.198 10 false A 0.469,2.302 0.625,2.5 0.156,0.198 10 false B 0.677,2.583 0.823,2.771 0.146,0.188 10 false B 2.719,2.385 2.854,2.552 0.135,0.167 10 true C 1.438,2.052 1.563,2.25 0.125,0.198 10 true A 1.188,1.76 1.323,1.958 0.135,0.198 10 true D 3.063,1.729 3.198,1.896 0.135,0.167 10 true C 2.188,1.344 2.344,1.542 0.156,0.198 10 true B 2.229,0.885 2.385,1.083 0.156,0.198 10 false A 2.26,0.583 2.417,0.781 0.156,0.198 10 false A 1.469,0.479 1.635,0.646 0.167,0.167 10 true B 2.021,2.594 2.167,2.781 0.146,0.188 10 false B 5.604,1.344 5.76,1.542 0.156,0.198 10 true 1 4.604,1.76 4.75,1.927 0.146,0.167 10 true 2 4.927,1.635 5.073,1.802 0.146,0.167 10 true 4 4.885,0.479 5.031,0.646 0.146,0.167 10 true 5 3.896,2.302 4.042,2.469 0.146,0.167 10 false 6 5.427,2.594 5.573,2.76 0.146,0.167 10 false 7 4.125,2.615 4.271,2.781 0.146,0.167 10 false 8 3.917,1.563 4.063,1.729 0.146,0.167 10 false 9 4.802,2.063 4.979,2.229 0.177,0.167 10 true 10 3.823,2 4,2.167 0.177,0.167 10 true 11 5.625,0.896 5.802,1.063 0.177,0.167 10 true 12 3.865,0.844 4.042,1.01 0.177,0.167 10 true 13 3.958,0.396 4.135,0.563 0.177,0.167 10 false 14 5.656,0.583 5.833,0.75 0.177,0.167 10 false 15 6.458,1.76 6.635,1.927 0.177,0.167 10 true 16 6.094,2.396 6.271,2.563 0.177,0.167 10 true 17 3.948,1.24 4.094,1.406 0.146,0.167 10 false 3
*a Types of nut and bolt *b Tightening order
V100135

Bolt
V100136

Nut


Torque:
for bolt A : 57 N*m (581 kgf*cm, 42 ft.*lbf)
for bolt B and nut : 23 N*m (235 kgf*cm, 17 ft.*lbf)
for bolt C : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt D : 25 N*m (255 kgf*cm, 18 ft.*lbf)

Bolt Length:
Item Length Thread Diameter
Bolt A 75 mm (2.95 in.) 10 mm (0.394 in.)
Bolt B 75 mm (2.95 in.) 8.0 mm (0.315 in.)
Bolt C 40 mm (1.57 in.) 8.0 mm (0.315 in.)
Bolt D 90 mm (3.54 in.) 8.0 mm (0.315 in.)


NOTICE:
·

Make sure that there is no oil on the threads of bolts.

·

Check the bolts and bolt holes, and clean and degrease them.




f.
A346229

Remove the seal packing from the 2 bolt holes for the No. 1 compressor mounting bracket.

NOTICE:

Do not use any cleaners to remove the seal packing.



Hide 12101 5.INSTALL OIL PAN SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.


b.
A344597C01
1.323,0.188 1.479,0.188 1.479,0.188 1.677,0.521 true 0.49,2.583 0.656,2.583 0.656,2.583 0.781,2.688 false 2.167,2.573 2.333,2.573 2.333,2.573 2.458,2.677 false 0.719,3.844 0.885,3.844 0.885,3.844 1.01,3.948 false 1.146,0.094 1.333,0.281 0.188,0.188 10 false *a 0.781,2.094 1.01,2.25 0.229,0.156 10 false *b 2.427,2.094 2.688,2.271 0.26,0.177 10 false *c 0.427,0.635 0.531,0.802 0.104,0.167 10 true A 0.646,0.635 0.76,0.802 0.115,0.167 10 true A 1.719,1.448 1.833,1.615 0.115,0.167 10 true B 1.729,1.708 1.844,1.875 0.115,0.167 10 true B 2.948,0.635 3.063,0.802 0.115,0.167 10 true C 3.219,0.625 3.333,0.792 0.115,0.167 10 true C 0.323,2.49 0.51,2.677 0.188,0.188 10 true *a 2,2.479 2.188,2.667 0.188,0.188 10 true *a 0.552,3.75 0.74,3.938 0.188,0.188 10 true *a 1.021,3.354 1.25,3.51 0.229,0.156 10 false *b 0.208,2.135 0.563,2.323 0.354,0.188 10 false A - A 1.885,2.104 2.344,2.302 0.458,0.198 10 false B - B 0.302,3.448 0.76,3.646 0.458,0.198 10 false C - C
*a Seal Packing
*b 8.0 mm (0.315 in.)
*c 6.5 mm (0.256 in.)


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Application Specification:
Area Seal Packing Diameter Distance from Edge of Cover or Center of Bolt Hole to Center of Seal Packing
A - A and C - C 2.0 to 3.0 mm (0.0787 to 0.118 in.) 8.0 mm (0.315 in.)
B - B 2.0 to 3.0 mm (0.0787 to 0.118 in.) 6.5 mm (0.256 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not start the engine for at least 4 hours after the installation.




c.
A344598C01
0.99,0.042 1.146,0.24 0.156,0.198 10 false 1 1.396,0.052 1.604,0.219 0.208,0.167 10 false 10 1.802,0.052 2.01,0.219 0.208,0.167 10 false 11 2.219,0.052 2.427,0.219 0.208,0.167 10 false 12 2.635,0.052 2.844,0.219 0.208,0.167 10 false 13 3,0.021 3.208,0.188 0.208,0.167 10 false 14 3.219,0.323 3.396,0.49 0.177,0.167 10 false 15 3.24,0.76 3.417,0.927 0.177,0.167 10 false 16 2.74,2.021 2.948,2.167 0.208,0.146 10 false 17 2.375,2.021 2.583,2.167 0.208,0.146 10 false 18 0.188,0.198 0.344,0.396 0.156,0.198 10 false 9 0.135,0.448 0.292,0.646 0.156,0.198 10 false 8 0.208,1.573 0.313,1.771 0.104,0.198 10 true 7 0.292,1.948 0.448,2.146 0.156,0.198 10 false 6 0.625,2.01 0.771,2.177 0.146,0.167 10 false 5 1.594,1.198 1.729,1.365 0.135,0.167 10 true 4 2.375,1.198 2.521,1.385 0.146,0.188 10 true 2 1.969,1.177 2.135,1.354 0.167,0.177 10 true 3
V100135

Bolt A
V100136

Bolt B
V100137

Nut


Temporarily install the oil pan sub-assembly with the 16 bolts and 2 nuts.

Bolt Length:
Item Length
Bolt A 20 mm (0.787 in.)
Bolt B 40 mm (1.57 in.)



d.

Uniformly tighten the 16 bolts and 2 nuts in the order shown in the illustration.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


Hide 15104 6.INSTALL OIL STRAINER SUB-ASSEMBLY

a.
A349941C01
1.219,0.135 1.448,0.135 1.448,0.135 1.615,0.26 true 1.698,0.302 2.052,0.177 2.052,0.177 2.198,0.177 true 1.031,0.042 1.188,0.229 0.156,0.188 10 true *a 2.229,0.094 2.542,0.25 0.313,0.156 10 false *b
*a Protrusion
*b Groove


Install a new gasket to the oil strainer sub-assembly.

HINT:

Align the protrusion of the gasket with the groove of the oil strainer sub-assembly.



b.
A334454N01
2.417,0.719 2.573,0.917 0.156,0.198 10 true 1 2.708,1.521 2.865,1.719 0.156,0.198 10 false 2 1.01,1.573 1.167,1.75 0.156,0.177 10 true 3

Install the oil strainer sub-assembly with the 2 bolts and nut in the sequence shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12102A 7.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.


b.
A344599C01
1.917,2.365 2.323,2.365 false 2.531,0.5 2.813,0.167 2.813,0.167 2.969,0.167 true 1.667,1.906 1.885,2.083 0.219,0.177 10 false *b 3.01,0.083 3.323,0.24 0.313,0.156 10 false *a 2.344,2.281 2.594,2.479 0.25,0.198 10 false *a 0.135,1.021 0.292,1.219 0.156,0.198 10 false A 0.531,1 0.667,1.177 0.135,0.177 10 true A
*a Seal Packing
*b 6.0 mm (0.236 in.)


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Application Specification:
Seal Packing Diameter Distance from Center of Bolt Hole to Center of Seal Packing
2.5 to 3.5 mm (0.0984 to 0.138 in.) 6.0 mm (0.236 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 oil pan sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not start the engine for at least 4 hours after the installation.




c.

Temporarily install the No. 2 oil pan sub-assembly with the 16 bolts, 4 adjusting screws and 2 nuts.


d.
A344600C01
1.031,0.073 1.375,0.25 0.344,0.177 10 true 1, 23 1.448,0.063 1.583,0.24 0.135,0.177 10 false 2 1.74,0.063 1.875,0.24 0.135,0.177 10 false 3 2,0.146 2.135,0.323 0.135,0.177 10 false 4 2.271,0.292 2.406,0.469 0.135,0.177 10 true 5 2.99,0.469 3.125,0.646 0.135,0.177 10 true 6 3.063,1.01 3.406,1.198 0.344,0.188 10 true 7, 24 3.01,1.677 3.125,1.875 0.115,0.198 10 true 8 2.333,1.927 2.469,2.104 0.135,0.177 10 true 9 2.042,1.958 2.229,2.135 0.188,0.177 10 false 10 1.76,1.927 1.948,2.104 0.188,0.177 10 false 11 1.458,1.927 1.646,2.104 0.188,0.177 10 false 12 1.01,1.917 1.438,2.104 0.427,0.188 10 false 13, 25 0.802,1.979 0.99,2.156 0.188,0.177 10 false 14 0.438,2.01 0.635,2.167 0.198,0.156 10 false 15 0.052,1.906 0.25,2.063 0.198,0.156 10 false 16 0.01,1.604 0.208,1.76 0.198,0.156 10 false 17 0,1.115 0.427,1.302 0.427,0.188 10 true 18, 26 0,0.396 0.198,0.552 0.198,0.156 10 false 19 0.135,0.063 0.333,0.219 0.198,0.156 10 false 20 0.458,0 0.656,0.156 0.198,0.156 10 false 21 0.813,0.031 1.01,0.188 0.198,0.156 10 false 22
V100135

Bolt
V100136

Nut
V100137

Adjusting Screw


Uniformly tighten the 16 bolts, 4 adjusting screws and 2 nuts in the order shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


e.

Install a new gasket and the oil pan drain plug.

Torque:
37.5 N*m (382 kgf*cm, 28 ft.*lbf)


Hide 12144 8.INSTALL OIL PAN COVER SILENCER

a.

Install the oil pan cover silencer with the 4 No. 1 oil pan plugs.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 13471 9.INSTALL CRANKSHAFT PULLEY

a.
A344601C01
1.292,0.802 0.885,0.26 true 0.677,0.26 0.896,0.26 0.896,0.26 1.552,0.771 true 1.521,1.938 1.76,2.115 0.24,0.177 10 false *a 0.375,0.208 0.667,0.406 0.292,0.198 10 false SST
*a Hold
V100135

Turn


Align the key groove of the crankshaft pulley with the pulley set key and slide on the crankshaft pulley.


b.

Using SST, install a new crankshaft pulley set bolt.

SST
09213-54015  (91651-60855)
09330-00021  

Torque:
260 N*m (2651 kgf*cm, 192 ft.*lbf)

NOTICE:

Do not reuse the crankshaft pulley set bolt.



Hide 11201 10.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the timing chain cover sub-assembly, cylinder head and cylinder head cover sub-assembly.


b.
A337640C01
0.604,1.896 0.76,2.094 0.156,0.198 10 false -
V100135

Seal Packing Application Area


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal packing diameter:

4.0 mm (0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add the engine oil for at least 4 hours after the installation.

·

Do not start the engine for at least 4 hours after the installation.




c.

Install a new No. 1 camshaft bearing cap oil hole gasket to the cylinder head cover connector sub-assembly.


d.

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.


e.
A337666C02
0.188,0.667 0.875,0.667 true 0.583,0.677 0.583,1.052 0.583,1.052 0.865,1.052 true 0.021,0.583 0.188,0.76 0.167,0.177 10 false *a 1.188,1.354 1.51,1.542 0.323,0.188 10 true 1, 24 1.208,0.542 1.552,0.698 0.344,0.156 10 true 2, 25 1.688,0.792 2.01,0.958 0.323,0.167 10 true 3, 26 1.677,1.438 2,1.625 0.323,0.188 10 true 4, 27 2.167,1.344 2.49,1.51 0.323,0.167 10 true 5, 28 2,0.615 2.323,0.771 0.323,0.156 10 true 6, 29 2.656,0.75 2.979,0.906 0.323,0.156 10 true 7, 30 2.594,1.448 2.927,1.625 0.333,0.177 10 true 8, 31 0.844,1.354 1.021,1.521 0.177,0.167 10 true 23 0.833,0.208 1.01,0.385 0.177,0.177 10 true 22 3.208,0.865 3.385,1.042 0.177,0.177 10 false 9 3.229,1.604 3.406,1.781 0.177,0.177 10 false 10 2.333,1.865 2.51,2.042 0.177,0.177 10 false 11 1.99,1.865 2.167,2.042 0.177,0.177 10 false 12 1.49,1.885 1.667,2.063 0.177,0.177 10 false 13 1.031,1.969 1.208,2.146 0.177,0.177 10 false 14 0.208,1.906 0.385,2.083 0.177,0.177 10 false 15 0.021,1.115 0.198,1.292 0.177,0.177 10 false 16 0.406,0.021 0.583,0.198 0.177,0.177 10 false 17 1.021,0.021 1.198,0.198 0.177,0.177 10 false 18 1.667,0.115 1.844,0.292 0.177,0.177 10 false 19 2.323,0.135 2.521,0.313 0.198,0.177 10 false 20 3.188,0.229 3.385,0.406 0.198,0.177 10 false 21
*a Plate Washer and Seal Washer
V100135

Bolt
V100136

Nut


Install the cylinder head cover sub-assembly, 2 plate washers and 2 seal washers with the 21 bolts and 2 nuts, and tighten the 21 bolts and 2 nuts in the sequence shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:

Make sure that the metal face of the seal washer is facing upward.



Hide 11101J 11.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11301M 12.INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11301M 13.INSTALL CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 12108 14.INSTALL OIL FILLER CAP SUB-ASSEMBLY

Hide 16268 15.INSTALL NO. 1 WATER BY-PASS PIPE

Hide 16603 16.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 16620D 17.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 88431 20.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 27020 21.INSTALL GENERATOR ASSEMBLY

Hide 23250 23.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23814B 24.INSTALL FUEL DELIVERY PIPE WITH FUEL INJECTOR ASSEMBLY

Hide 23270 25.INSTALL FUEL PRESSURE PULSATION DAMPER ASSEMBLY

Hide 22030 26.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 30.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND