1.REMOVE ENGINE ASSEMBLY
2.INSTALL ENGINE TO ENGINE STAND
11301M
3.REMOVE VVT SENSOR (for Bank 1)
11301M
4.REMOVE VVT SENSOR (for Bank 2)
15330B
5.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)
15340
6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)
19500
7.REMOVE IGNITION COIL ASSEMBLY
11452
8.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
16031
9.REMOVE WATER INLET ASSEMBLY
16620
10.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
16604
11.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY
16603
12.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
13471
13.REMOVE CRANKSHAFT PULLEY
| *a | Hold |
| *b | Loosen |
Using SST, hold the crankshaft pulley and loosen the crankshaft pulley set bolt.
Screw the crankshaft pulley set bolt into the crankshaft by 2 or 3 threads.
| *1 | Crankshaft Pulley Set Bolt |
| *a | Hold |
| *b | Turn |
Using the crankshaft pulley set bolt and SST, remove the crankshaft pulley and crankshaft pulley set bolt.
12102A
14.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
|
Bolt |
|
Nut |
Remove the 14 bolts and 2 nuts.
| *a | Oil Pan Seal Cutter |
Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and No. 2 oil pan sub-assembly. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.
Be careful not to damage the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.
Be careful not to damage the flange of the No. 2 oil pan sub-assembly.
15104
15.REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.
12101
16.REMOVE OIL PAN SUB-ASSEMBLY
|
Bolt |
|
Nut |
Remove the 17 bolts and 2 nuts.
| *a | Protective Tape |
Using a screwdriver, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block as shown in the illustration.
Be careful not to damage the contact surfaces of the cylinder block and oil pan sub-assembly.
Tape the screwdriver tip before use.
Remove the O-ring from the timing chain cover sub-assembly.
23801P
17.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY AND NO. 2 FUEL PIPE SUB-ASSEMBLY
11201
18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
|
Bolt |
|
Nut |
Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover sub-assembly and cylinder head cover gasket.
11202
19.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
|
Bolt |
|
Nut |
Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover sub-assembly LH and cylinder head cover gasket.
15601
20.REMOVE OIL FILTER SUB-ASSEMBLY
15609
21.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY
|
Bolt |
|
Nut |
Remove the 3 bolts, 2 nuts, oil filter bracket sub-assembly and gasket.
11302
22.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
|
Bolt |
|
Nut |
Remove the 24 bolts and 2 nuts.
| *a | Protective Tape |
Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.
Be careful not to damage the contact surfaces of the timing chain cover sub-assembly, cylinder block sub-assembly and cylinder head sub-assembly.
Tape the screwdriver tip before use.
Remove the O-ring from the cylinder head LH.
11303A
23.REMOVE FRONT CRANKSHAFT OIL SEAL
Using a screwdriver and wooden block, pry out the front crankshaft oil seal.
Tape the screwdriver tip before use.
Do not damage the surface of the oil seal press fit hole and crankshaft.