Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2015.06–2016.01
RM3250E _51 Engine / Hybrid System _037982 1GR-FE ENGINE MECHANICAL _0177654 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of ECM Vehicle Identification Number (VIN) registration DTC P0630 is output (Click here)
Code registration
(Immobiliser system)
Engine start function See the Service Bulletin for the registration method.
Replacement of engine assembly Inspection after repair Poor idle, engine start, etc. (Click here)
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of cylinder head LH

·

Replacement of camshaft

·

Replacement of No. 2 camshaft

·

Replacement of No. 3 camshaft sub-assembly

·

Replacement of No. 4 camshaft sub-assembly

·

Replacement of camshaft timing gear assembly

·

Replacement of piston sub-assembly

·

Replacement of piston ring

·

Replacement of intake mass air flow meter sub-assembly

·

Replacement of fuel injector assembly

·

Replacement of fuel pump

·

Replacement of air fuel ratio sensor

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Replacement of knock sensor


Inspection after repair Poor idle, engine start, etc. (Click here)
for AC60E:
·

Automatic transmission assembly

·

Transmission valve body assembly

·

Any of the shift solenoid valves


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AC60E:

Automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
for AC60F:
·

Automatic transmission assembly

·

Transmission valve body assembly

·

Any of the shift solenoid valves


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AC60F:

Automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly may fall off the engine lifter.

·
A343690

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.

·
A343701

Do not remove the radiator cap sub-assembly,cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

·
A358535

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A358533

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 53301 6.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer nozzle hose.


b.

Remove the 4 bolts and hood sub-assembly.


Hide 51410 7.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (for 4WD)

Hide 51442 8.REMOVE NO. 2 ENGINE UNDER COVER (for 4WD)

Hide 51407A 9.REMOVE NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY (for 4WD)

Hide 10.DRAIN DIFFERENTIAL OIL (for 4WD)

Hide 53735B 11.REMOVE FRONT UPPER FENDER APRON SEAL LH

a.

Remove the 6 clips and front upper fender apron seal LH.


Hide 53735B 12.REMOVE FRONT UPPER FENDER APRON SEAL RH

a.

Remove the 6 clips and front upper fender apron seal RH.


Hide 53882F 13.REMOVE FRONT FENDER SEAL LH

a.

for 2WD:

Remove the 5 clips and front fender seal LH.


b.

for 4WD:

Remove the 6 clips and front fender seal LH.


Hide 53882F 14.REMOVE FRONT FENDER SEAL RH

a.

for 2WD:

Remove the 5 clips and front fender seal RH.


b.

for 4WD:

Remove the 6 clips and front fender seal RH.


Hide 53294C 15.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 53293C 16.REMOVE RADIATOR SIDE DEFLECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 17705 17.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE

Hide 17801 18.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 19.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A346258

Disconnect the 3 clamps from the air cleaner case sub-assembly.


b.

Remove the 3 bolts and air cleaner case sub-assembly.


Hide 16593 20.REMOVE NO. 1 RADIATOR AIR GUIDE

Hide 16571 21.REMOVE RADIATOR HOSE INLET

Hide 16572 22.REMOVE RADIATOR HOSE OUTLET

Hide 16470 23.REMOVE RADIATOR RESERVOIR

Hide 16711 24.REMOVE FAN SHROUD

Hide 32941 25.DISCONNECT NO. 1 OIL COOLER INLET HOSE

Hide 32942 26.DISCONNECT NO. 1 OIL COOLER OUTLET HOSE

Hide 16400 27.REMOVE RADIATOR ASSEMBLY

Hide 44320 28.DISCONNECT VANE PUMP ASSEMBLY

a.
A344578

Disconnect the connector.


b.

Remove the 2 bolts and disconnect the vane pump assembly.

NOTICE:

Do not hit other parts with the pulley when disconnecting the vane pump assembly.


HINT:

Be sure to suspend the vane pump assembly securely.



Hide 17129 29.REMOVE INTAKE AIR SURGE TANK

Hide 17450B 30.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 17410 31.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 17104 33.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17119 34.REMOVE NO. 2 MANIFOLD STAY

Hide 17105 35.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 28100 36.REMOVE STARTER ASSEMBLY

Hide 11363A 37.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 55607 38.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Cover)

Hide 55550 39.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 82121 41.DISCONNECT ENGINE WIRE

a.
A340245

Detach the 2 clamps and disconnect the 3 connectors from the instrument panel wire.


b.
A346253

Disconnect the connector.


c.
A346254

Remove the bolt and disconnect the engine wire.


d.
A346255

Detach the clamp and disconnect the engine wire from the bracket.


e.

Detach the grommet and pull out the engine wire from the cabin.


f.
A349973

Remove the nut and disconnect the engine room main wire from the battery positive cable.


g.
A349974

Loosen the nut and remove the positive (+) battery terminal.


h.
A349975

Loosen the 2 nuts and remove the battery hold down clamp.


i.

Remove the battery.


j.

Remove the battery tray.


k.
A349976

Detach the 2 clamps and remove the 2 bolts and disconnect the No. 2 engine wire.


l.
A349977

Detach the 3 claws and remove the No. 1 relay block cover upper from the engine room relay block.


m.
A349978

Detach the 2 claws and remove the No. 1 relay block cover side from the engine room relay block.


n.
A349979

Remove the nut and disconnect the engine wire from the engine room relay block.


o.

Disconnect the 2 connectors from the engine room relay block.


Hide 88320 43.DISCONNECT COOLER COMPRESSOR ASSEMBLY

Hide 44.REMOVE WATER HOSE SUB-ASSEMBLY

a.
A346252

Remove the bolt.


b.

Slide the 4 clamps and remove the water hose sub-assembly.


Hide 23801P 45.DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23802B 46.DISCONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

A346256

a.

Slide the clamp and disconnect the No. 2 fuel pipe sub-assembly.


Hide 37140 48.REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

Hide 43514C 49.REMOVE FRONT AXLE HUB GREASE CAP (for 4WD)

Hide 43502H 50.REMOVE FRONT AXLE SHAFT NUT (for 4WD)

Hide 89543 51.DISCONNECT FRONT SPEED SENSOR LH (for 4WD)

Hide 52.DISCONNECT TIE ROD END SUB-ASSEMBLY LH (for 4WD)

Hide 48069 53.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for 4WD)

Hide 43420 54.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH (for 4WD)

Hide 43410D 55.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING (for 4WD)

Hide 43410 56.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:

Use the same procedure described for the LH side.


Hide 45219 57.DISCONNECT STEERING SLIDING YOKE (for 4WD)

Hide 58.REMOVE POWER STEERING LINK ASSEMBLY (for 4WD)

Hide 41110F 59.REMOVE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

Hide 37100 61.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 2WD)

Hide 37100 62.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)

Hide 63.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 32101 65.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 66.INSTALL ENGINE HANGER

a.
A344580C01
0.333,0.313 0.552,0.313 0.552,0.313 0.792,0.688 true 2.292,0.313 2.51,0.313 2.51,0.313 2.792,0.667 true 0.135,0.24 0.344,0.448 0.208,0.208 10 true *1 2.094,0.24 2.323,0.427 0.229,0.188 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-31060
No. 2 Engine Hanger 12282-31040
Bolt 90119-08A87



Hide 11000 67.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.
A344581

Remove the 4 bolts and 4 nuts from the body.


c.

Remove the engine assembly by operating the engine sling device and chain block.

NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While lowering the engine from the vehicle, do not allow it to contact the vehicle.




Hide 11000 68.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine to an engine stand with bolts.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.




b.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.