Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT › 2015.06–2016.01
RM3250E _58 Vehicle Interior _038073 HEATING / AIR CONDITIONING _0178610 FRONT AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 87211B 1.INSTALL NO. 3 AIR DUCT

a.
E320373

Attach the claw to install the No. 3 air duct.


Hide 2.INSTALL AIR CONDITIONING UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When installing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

Temporarily install the air conditioning unit assembly and instrument panel reinforcement assembly with the nut.

E320387C02
1.417,3.542 1.281,3.542 1.281,3.542 1.26,3.219 false 1.458,3.448 1.771,3.604 0.313,0.156 10 false *a
*a Standard Position - -



b.

Align the standard position, install the drain cooler hose.


c.

Tighten the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 55950G 3.INSTALL DEFROSTER NOZZLE ASSEMBLY

E320371

a.

Attach the claw to install the defroster nozzle assembly.


Hide 55330B 4.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When installing the air conditioning unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

for Automatic Transmission:

Install the 11 bolts.

E320370C02
1.094,0.906 1.344,1.063 0.25,0.156 10 true *A
*A for Manual Transmission - -
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Bolt D


Torque:
Bolt A : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Bolt B : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

for Manual Transmission:

Install the 12 bolts.

Torque:
Bolt A : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Bolt B : 18 N*m (184 kgf*cm, 13 ft.*lbf)


c.
E325413C01
0.073,0.104 0.385,0.26 0.313,0.156 10 true *A
*A for Driver Side


Install 2 new hole plugs.


Hide 55306A 5.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E320365C02
0,0 0,0 false
V100135

Nut
V100136

Bolt
V100137

Screw


Install the No. 1 instrument panel brace sub-assembly with the nut, bolt and 4 screws.

Torque:
Bolt, Nut : 20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Attach the clamp.


Hide 55307C 6.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E320366C02
0,0 0,0 false
V100135

Nut
V100136

Bolt
V100137

Screw


Install the No. 2 instrument panel brace sub-assembly with the nut, bolt and 3 screws.

Torque:
Bolt, Nut : 20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 7.TIGHTEN AIR CONDITIONER UNIT ASSEMBLY

a.

Tighten the 2 screws and 3 bolts in the order shown in the illustration.

Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)

E323709C01
3.125,1.406 3.333,1.604 0.208,0.198 10 true (1) 4.688,1.052 4.896,1.25 0.208,0.198 10 true (2) 4.021,1.26 4.229,1.458 0.208,0.198 10 true (3) 3.354,1.927 3.563,2.125 0.208,0.198 10 true (4) 4.094,1.792 4.302,1.99 0.208,0.198 10 true (4)
V100135

Bolt
V100136

Screw



Hide 82141 8.CONNECT INSTRUMENT PANEL WIRE

a.

Install each bolt, nut and screw, and then connect the instrument panel wire.

E324630C01
2.021,5.854 2.333,6.01 0.313,0.156 10 true *A 4.229,5.865 4.542,6.021 0.313,0.156 10 true *B 2.292,4.354 2.604,4.51 0.313,0.156 10 true *C 3.208,1.208 3.417,1.375 0.208,0.167 10 true *1 2.74,0.5 2.948,0.667 0.208,0.167 10 true *1 3.698,1.094 3.906,1.26 0.208,0.167 10 true *1 4.344,1.021 4.552,1.188 0.208,0.167 10 true *1 3.792,0.208 4,0.375 0.208,0.167 10 true *1 6.521,0.813 6.729,0.979 0.208,0.167 10 true *1
*A for Manual Air Conditioning System, Manual Cooler System *B for Automatic Air Conditioning System
*C w/ PTC Heater - -
*1 Ground Wire - -



b.

Connect each connector and attach each clamp.


c.

Install each bolt and each ground wire.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


d.
E320367

for Automatic Air Conditioning System:

i.

Attach the clamp.


ii.

Connect the connector.



e.
E320368

for Manual Air Conditioning System, Manual Cooler System:

i.

Attach the clamp.


ii.

Connect the connector.



Hide 87212 9.INSTALL NO. 1 REAR AIR DUCT (w/ Rear Foot Duct)

a.
E324638

Install the No. 1 rear air duct with the 2 clips.


Hide 87212G 10.INSTALL NO. 3 REAR AIR DUCT (w/ Rear Foot Duct)

a.
E324637

Attach the claw to install the No. 3 rear air duct.


Hide 87213 11.INSTALL NO. 2 REAR AIR DUCT (w/ Rear Foot Duct)

a.
E324636

Attach the claw to install the No. 2 rear air duct.


Hide 87216A 12.INSTALL NO. 5 REAR AIR DUCT (w/ Rear Foot Duct)

a.
E324635

Attach the claw to install the No. 5 rear air duct.


Hide 87216B 13.INSTALL NO. 4 REAR AIR DUCT (w/ Rear Foot Duct)

a.
E324634

Attach the claw to install the No. 4 rear air duct.


Hide 58861B 14.INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Resistor Duct)

a.
E320364

for Automatic Transmission:

i.

Install the No. 1 console box duct with the 2 clips.


ii.
E320363C02
0.333,0.188 0.563,0.344 0.229,0.156 10 true *A
*A w/ Smart Entry and Start System


w/ Smart Entry and Start System:

Attach the clamp to install the No. 2 console box mounting bracket.


iii.

Install the 2 bolts.



b.
E323938

for Manual Transmission:

i.

Install the No. 1 console box duct with the 3 clips.


ii.
E323937C01
2.333,0.25 2.594,0.406 0.26,0.156 10 true *A
*A w/ Smart Entry and Start System


w/ Smart Entry and Start System

Attach the clamp to install the No. 2 console box mounting bracket.


iii.

Install the 2 bolts.



Hide 55215D 15.INSTALL NO. 3 DASH PANEL INSULATOR PAD

a.
E320362

Install the No. 3 dash panel insulator pad.


Hide 55214C 16.INSTALL NO. 2 DASH PANEL INSULATOR PAD

a.
E320361

Install the No. 2 dash panel insulator pad.


Hide 55395C 17.INSTALL NO. 1 INSTRUMENT PANEL INNER BRACKET COVER LH (for LHD)

a.
E323201

Install the No. 1 instrument panel inner bracket cover LH with the 3 clips.


Hide 18.INSTALL FRONT FLOOR CARPET ASSEMBLY

a.

Attach the guide to install the front floor carpet assembly to the original position as shown in the illustration.

E320388C02
1.771,1.125 2.083,1.323 0.313,0.198 10 true *A
*A for LHD - -
V100155

Fastener
V113147

Install in this Direction



b.

Attach each fastener.


c.

for LHD:

Install the 5 clips.


d.

for RHD:

Install the 4 clips.


Hide 62414A 19.INSTALL LOWER CENTER PILLAR GARNISH LH (for Double Cab)

Hide 62413A 20.INSTALL LOWER CENTER PILLAR GARNISH RH (for Double Cab)

Hide 67918E 21.INSTALL REAR DOOR SCUFF PLATE LH (for Double Cab)

Hide 67917C 22.INSTALL REAR DOOR SCUFF PLATE RH (for Double Cab)

Hide 62112 23.INSTALL COWL SIDE TRIM BOARD LH

Hide 62111C 25.INSTALL COWL SIDE TRIM BOARD RH

Hide 27.INSTALL STEERING COLUMN ASSEMBLY

Hide 87211 28.INSTALL NO. 1 AIR DUCT

a.
E320358

Attach the claw to install the No. 1 air duct.

NOTICE:

If the No. 1 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.



b.

Install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87211A 29.INSTALL NO. 2 AIR DUCT

E320359

a.

Attach the claw to install the No. 2 air duct.

NOTICE:

If the No. 2 air duct is reused, it may fall off or abnormal noise may occur. Therefore, make sure to replace it with a new one.



Hide 55303B 30.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 58810J 31.INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58811A 32.INSTALL FRONT CONSOLE BOX (w/o Console Box Lid)

Hide 34.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 87128 35.INSTALL HEATER GROMMET (w/ Heater)

E315751

a.

Press the marked parts to attach the claw and install the heater grommet.

NOTICE:
·

Securely install the heater grommet in order to prevent water ingress.

·

Install the heater grommet so that there is no clearance between the grommet and heater pipe.




Hide 36.CONNECT HEATER WATER INLET HOSE (w/ Heater)

a.
E315772C02
1.042,3.854 1.167,3.854 1.167,3.854 1.219,3.771 false 0.677,2.594 0.99,2.75 0.313,0.156 10 false *a 0.885,3.76 1.198,3.917 0.313,0.156 10 false *b 0.542,3.781 0.854,3.938 0.313,0.156 10 false *c 2.406,0.865 2.563,1.063 0.156,0.198 10 true A
*a View A
*b for 1GR-FE: Marking (Yellow)
for 1GD-FTV, 2GD-FTV: Marking (Yellow)
for 1KD-FTV, 2KD-FTV: Marking (Yellow)
for 1TR-FE, 2TR-FE: Marking (Yellow)
*c Clip Installation Angle (45°)


Connect the heater water inlet hose with the marking facing left and attach the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the heater water inlet hose.



Hide 37.CONNECT HEATER WATER OUTLET HOSE (w/ Heater)

a.
E315773C01
0.875,3.198 1.01,3.198 1.01,3.198 1.094,3.281 false 0.583,2.313 0.896,2.469 0.313,0.156 10 false *a 0.698,3.125 1.01,3.281 0.313,0.156 10 false *b 0.406,3.458 0.719,3.615 0.313,0.156 10 false *c 2.021,0.458 2.177,0.656 0.156,0.198 10 true A
*a View A
*b for 1GR-FE: Marking (White)
for 1GD-FTV, 2GD-FTV: Marking (White)
for 1KD-FTV, 2KD-FTV: Marking (White)
for 1TR-FE, 2TR-FE: Marking (White)
*c Clip Installation Angle (40°)


Connect the heater water outlet hose with the marking facing left and attach the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the heater water outlet hose.



Hide 17129 38.INSTALL INTAKE AIR SURGE TANK (for 1GR-FE)

Hide 88710E 39.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (except 1GD-FTV, 2GD-FTV)

a.
E315748

Remove the vinyl tape from the air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.

Connect the air conditioner tube and accessory assembly.


Hide 88707 40.CONNECT SUCTION PIPE SUB-ASSEMBLY (except 1GD-FTV, 2GD-FTV)

a.
E315747

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.

Connect the suction pipe sub-assembly.


e.
E315774C01
0,0 0,0 false
V113147

Install in this Direction


Rotate the hook connector as shown in the illustration.


f.

Insert the pipe joint into the fitting hole securely and tighten the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 88710E 41.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (for 1GD-FTV, 2GD-FTV)

a.
E315746

Remove the vinyl tape from the air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the 2 O-rings to the air conditioner tube and accessory assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the air conditioner tube and accessory assembly.


e.

Tighten the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 44. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 47. INITIALIZATION SERVO MOTOR (for Automatic Air Conditioning System)