Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL RELAY › 2015.06–2016.01
RM3250E _58 Vehicle Interior _038064 DOOR LOCK _0186388 DOOR CONTROL RELAY G

DOOR LOCK  DOOR CONTROL RELAY  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION (w/ Airbag System)

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45100 3.REMOVE STEERING WHEEL ASSEMBLY

Hide 55410C 4.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 55900 8.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 84930G 9.REMOVE DOOR LOCK CONTROL RELAY

a.
B438905C07
1.625,0.698 1.354,0.323 1.354,0.323 1.073,0.323 true 1.646,1.083 1.302,1.521 1.302,1.521 1.021,1.521 true 0.854,0.24 1.167,0.438 0.313,0.198 10 true *1 0.854,1.438 1.167,1.635 0.313,0.198 10 true *2
*1 No. 1 Door Lock Control Relay
*2 No. 2 Door Lock Control Relay


Remove the door lock control relay.


Hide 84930G 10.INSPECT NO. 1 DOOR LOCK CONTROL RELAY

a.
B441598N08
2.875,1.24 2.979,1.24 false 2.875,1.583 2.979,1.583 false 2.188,1.063 2.26,0.969 false 2.563,1.063 2.635,0.969 false 2.969,1.073 3.042,0.979 false 1.573,0.896 1.729,1.094 0.156,0.198 10 false 5 1.573,1.396 1.729,1.594 0.156,0.198 10 false 2 1.573,0.396 1.729,0.594 0.156,0.198 10 false 4 0.281,0.688 0.438,0.885 0.156,0.198 10 false 3 0.292,1.396 0.448,1.594 0.156,0.198 10 false 1 3.031,1.177 3.188,1.375 0.156,0.198 10 false 5 3.031,1.521 3.188,1.719 0.156,0.198 10 false 3 2.104,1.031 2.26,1.229 0.156,0.198 10 false 1 2.458,1.021 2.615,1.219 0.156,0.198 10 false 4 2.854,1.01 3.01,1.208 0.156,0.198 10 false 2

Inspect the No. 1 door lock control relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 1 door lock control relay.



Hide 84930H 11.INSPECT NO. 2 DOOR LOCK CONTROL RELAY

a.
B441598N09
2.875,1.24 2.979,1.24 false 2.875,1.583 2.979,1.583 false 2.188,1.063 2.26,0.969 false 2.563,1.063 2.635,0.969 false 2.969,1.073 3.042,0.979 false 1.573,0.896 1.729,1.094 0.156,0.198 10 false 5 1.573,1.396 1.729,1.594 0.156,0.198 10 false 2 1.573,0.396 1.729,0.594 0.156,0.198 10 false 4 0.281,0.688 0.438,0.885 0.156,0.198 10 false 3 0.292,1.396 0.448,1.594 0.156,0.198 10 false 1 3.031,1.177 3.188,1.375 0.156,0.198 10 false 5 3.031,1.521 3.188,1.719 0.156,0.198 10 false 3 2.104,1.031 2.26,1.229 0.156,0.198 10 false 1 2.458,1.021 2.615,1.219 0.156,0.198 10 false 4 2.854,1.01 3.01,1.208 0.156,0.198 10 false 2

Inspect the No. 2 door lock control relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied to terminals 1 and 2 Below 1 Ω
Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the No. 2 door lock control relay.



Hide 84930G 12.INSTALL DOOR LOCK CONTROL RELAY

a.
B438905C08
1.625,0.698 1.354,0.323 1.354,0.323 1.073,0.323 true 1.646,1.083 1.302,1.521 1.302,1.521 1.021,1.521 true 0.854,0.24 1.167,0.438 0.313,0.198 10 true *1 0.854,1.438 1.167,1.635 0.313,0.198 10 true *2
*1 No. 1 Door Lock Control Relay
*2 No. 2 Door Lock Control Relay


Install the door lock control relay.


Hide 55900 16.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 55410C 17.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

Hide 45100 18.INSTALL STEERING WHEEL ASSEMBLY

Hide 19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION