The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the oil pump removal/installation are shown below.
When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
| Replaced Parts (A) | Pipes Requiring New Replacement |
|---|---|
·
Injector assembly (including shuffling the injector assemblies between the cylinders) ·
Common rail assembly ·
Cylinder head sub-assembly |
·
No. 1 injection pipe sub-assembly ·
No. 2 injection pipe sub-assembly ·
No. 3 injection pipe sub-assembly ·
No. 4 injection pipe sub-assembly |
·
Supply pump assembly ·
Common rail assembly ·
Cylinder block sub-assembly ·
Cylinder head sub-assembly ·
Cylinder head gasket ·
Timing Gear Case Assembly |
Fuel inlet pipe sub-assembly |
After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.DRAIN ENGINE OIL
4.DRAIN ENGINE COOLANT
5.REMOVE ENGINE ASSEMBLY
11322A
6.REMOVE NO. 1 TIMING BELT COVER
13568
7.REMOVE TIMING BELT
13505
8.REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
88440D
9.REMOVE NO. 2 IDLE PULLEY ASSEMBLY
27020
10.REMOVE GENERATOR ASSEMBLY
12511C
11.REMOVE GENERATOR BRACKET
16620
12.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
88431
13.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
17118
14.REMOVE MANIFOLD STAY
15301
15.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
23701
16.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY
23704
17.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY
23804C
18.REMOVE FUEL INLET PIPE SUB-ASSEMBLY
23770
19.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
11201
20.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
13523P
21.REMOVE CAMSHAFT TIMING PULLEY
11322B
22.REMOVE NO. 2 TIMING BELT COVER
16100
23.REMOVE ENGINE WATER PUMP ASSEMBLY
29300
24.REMOVE VACUUM PUMP ASSEMBLY
44320
25.REMOVE VANE PUMP ASSEMBLY
26.REMOVE CAMSHAFT POSITION SENSOR
27.REMOVE CRANKSHAFT POSITION SENSOR
13522P
28.REMOVE PUMP DRIVE SHAFT PULLEY
Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley from the timing gear cover.
Using SST, hold the crankshaft pulley and remove the nut and O-ring.
13408
29.REMOVE CRANKSHAFT PULLEY SUB-ASSEMBLY
30.REMOVE TIMING GEAR COVER
13613E
31.REMOVE INJECTION GEAR
19315
32.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
13521
33.REMOVE CRANKSHAFT TIMING GEAR
13572
34.REMOVE IDLE GEAR THRUST PLATE
13525
35.REMOVE NO. 1 IDLE GEAR
13581
36.REMOVE NO. 1 IDLE GEAR SHAFT
22100
37.REMOVE FUEL SUPPLY PUMP ASSEMBLY
12101
38.REMOVE OIL PAN SUB-ASSEMBLY
15104
39.REMOVE OIL STRAINER SUB-ASSEMBLY
11320
40.REMOVE TIMING GEAR CASE ASSEMBLY