Home › Engine / Hybrid System › 5L-E ENGINE MECHANICAL › CYLINDER HEAD GASKET › from 2016.01
RM3250E _51 Engine / Hybrid System _049911 5L-E ENGINE MECHANICAL _0245945 CYLINDER HEAD GASKET A

5L-E ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.
A058740C01
2.625,0.521 2.813,0.365 2.813,0.365 2.906,0.365 false 3.063,1.281 2.979,1.281 2.979,1.281 2.75,1.365 false 2.969,0.26 3.125,0.417 0.156,0.156 10 false *a 3.083,1.188 3.24,1.344 0.156,0.156 10 false *b
*a Measuring Tip
*b Protrusion


Check the piston protrusion for each cylinder.

i.

Clean the cylinder block sub-assembly with solvent.


ii.

Set the piston of the cylinder to be measured to slightly before TDC.


iii.
A056896C02
3.083,1.563 3.302,1.76 0.219,0.198 10 true *b 0.188,1.417 0.396,1.635 0.208,0.219 10 true *b 0.302,1.958 0.688,2.156 0.385,0.198 10 true X: *a
*a Measuring Point
*b 25.0 mm (0.984 in.)
V100135

Front


Place a dial indicator on the cylinder block sub-assembly, and position the measuring tip as shown in the illustration.


iv.

Set the dial indicator at 0 mm (0 in.).

HINT:

Make sure that the measuring tip is square to the cylinder block sub-assembly gasket surface and piston head when taking the measurements.



v.

Measure the protrusion of each cylinder at 2 places as shown in the illustration, making a total of 8 measurements.


vi.

For the piston protrusion value of each cylinder, use the average of the 2 measurements of that cylinder.

Standard protrusion:

0.68 to 0.98 mm (0.0268 to 0.0386 in.)


HINT:

When installing the piston and connecting rod sub-assembly, if the protrusion is not as specified, remove the piston and connecting rod sub-assembly and reinstall them.



vii.

Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.



b.
A118135C02
1.938,1.646 2.25,1.844 0.313,0.198 10 false *a 2.792,1.948 3.104,2.146 0.313,0.198 10 false *a 1.333,0.542 1.49,0.74 0.156,0.198 10 false B 1.802,0.729 1.958,0.927 0.156,0.198 10 false D 2.927,0.896 3.083,1.094 0.156,0.198 10 false F
*a Cutout Mark
V100135

Front


Select a new cylinder head gasket.

HINT:

New cylinder head gaskets are available in 3 sizes, and are marked using cutouts for size B, D or F.


New Cylinder Head Gasket Thickness:
Mark Specified Condition
B 1.40 to 1.50 mm (0.0552 to 0.0590 in.)
D 1.50 to 1.60 mm (0.0591 to 0.0629 in.)
F 1.60 to 1.70 mm (0.0630 to 0.0669 in.)


i.

Select the largest piston protrusion value from the measurements made. Then select a new appropriate cylinder head gasket according to the table below.

Gasket Size:
Item Specified Condition
Piston protrusion 0.73 to 0.78 mm (0.0288 to 0.0307 in.) 0.83 to 0.88 mm (0.0327 to 0.0346 in.) 0.93 to 0.98 mm (0.0367 to 0.0385 in.)
Gasket to be used B D F




c.

Place a new cylinder head gasket in position on the cylinder block sub-assembly.

NOTICE:
A056909

Make sure the cylinder head gasket is installed facing the proper direction.



Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
·

The cylinder head set bolts are tightened in 3 progressive steps.

·

Set the No. 1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.

·

If any cylinder head set bolt is broken or deformed, replace it.



A374973C01
0.5,1.521 1.146,1.979 1.146,1.979 0.615,1.479 true 1.177,1.906 1.49,2.104 0.313,0.198 10 false *a
*a Timing Mark
V100135

Turn


a.

Using the crankshaft pulley bolt, turn the crankshaft 90° counterclockwise, and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case sub-assembly.


b.

Place the cylinder head sub-assembly on the cylinder block sub-assembly.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head sub-assembly.

·

Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the cylinder head gasket with the bottom part of the cylinder head sub-assembly.




c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


d.
A058739N01
3.031,0.76 3.219,0.906 0.188,0.146 10 false 15 2.417,0.771 2.521,0.917 0.104,0.146 10 false 7 1.74,0.771 1.833,0.917 0.094,0.146 10 false 1 1.042,0.771 1.146,0.917 0.104,0.146 10 false 9 0.323,0.781 0.51,0.927 0.188,0.146 10 false 17 3.073,2.208 3.26,2.354 0.188,0.146 10 false 18 2.396,2.208 2.583,2.354 0.188,0.146 10 false 10 1.75,2.208 1.844,2.354 0.094,0.146 10 false 2 1.042,2.208 1.146,2.354 0.104,0.146 10 false 8 0.344,2.365 0.563,2.531 0.219,0.167 10 false B 0.313,2.208 0.5,2.354 0.188,0.146 10 false 16 2.719,0.51 2.938,0.677 0.219,0.167 10 false A 2.688,0.667 2.875,0.813 0.188,0.146 10 false 13 2.052,0.667 2.156,0.813 0.104,0.146 10 false 5 1.375,0.667 1.479,0.813 0.104,0.146 10 false 3 0.656,0.667 0.844,0.813 0.188,0.146 10 false 11 2.75,2.427 2.938,2.573 0.188,0.146 10 false 12 2.115,2.427 2.219,2.573 0.104,0.146 10 false 4 1.448,2.427 1.552,2.573 0.104,0.146 10 false 6 0.688,2.427 0.875,2.573 0.188,0.146 10 false 14 0.74,2.583 0.958,2.75 0.219,0.167 10 false B 1.042,2.354 1.26,2.521 0.219,0.167 10 false B 1.438,2.604 1.656,2.771 0.219,0.167 10 false B 1.74,2.375 1.958,2.542 0.219,0.167 10 false B 2.104,2.573 2.323,2.74 0.219,0.167 10 false B 2.438,2.354 2.656,2.521 0.219,0.167 10 false B 2.792,2.573 3.01,2.74 0.219,0.167 10 false B 3.115,2.344 3.333,2.51 0.219,0.167 10 false B 0.354,0.604 0.573,0.771 0.219,0.167 10 false B 1.031,0.615 1.25,0.781 0.219,0.167 10 false B 1.729,0.604 1.948,0.771 0.219,0.167 10 false B 2.406,0.604 2.625,0.771 0.219,0.167 10 false B 3.063,0.583 3.281,0.75 0.219,0.167 10 false B 2.042,0.51 2.26,0.677 0.219,0.167 10 false A 1.365,0.521 1.583,0.688 0.219,0.167 10 false A 0.688,0.521 0.906,0.688 0.219,0.167 10 false A

Install and uniformly tighten the 18 cylinder head set bolts, in several passes in the sequence shown in the illustration.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

Standard Bolt Length
Item Specified Condition
Bolt A 107 mm (4.21 in.)
Bolt B 127 mm (5.00 in.)

If any of the cylinder head set bolts does not meet the torque specification, replace it.


e.
A060141C07
0.781,0.708 0.781,1.375 true 0.25,1.01 0.438,1.177 0.188,0.167 10 false *a 1.156,0.969 1.469,1.156 0.313,0.188 10 false 90° 1.802,0.531 2.115,0.719 0.313,0.188 10 false 90° 0.813,0.073 1.125,0.26 0.313,0.188 10 false 90° 0.052,0.479 0.365,0.667 0.313,0.188 10 false 90° 0.688,1.406 0.854,1.573 0.167,0.167 10 false *b
*a Front
*b Paint Mark


Mark the front of each cylinder head set bolt with paint.


f.

Further tighten the cylinder head set bolts by 90° in the sequence shown in the illustration above.


g.

Finally, tighten the cylinder head set bolts by an additional 90°.


h.

Check that the painted mark are now facing rearward.


Hide 23770B 3.CONNECT FUEL HOSE

a.

Connect the fuel hose to the nozzle leakage pipe assembly, and slide the clamp to secure the hose.


Hide 4.CONNECT WIRE HARNESS

a.

Attach the 7 wire harness clamps and connect the wire harness.


b.

Connect the engine coolant temperature sensor connector.


c.

Connect the engine wire and install the No. 2 glow plug resistor insulator and plate washer with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 23701 5.INSTALL INJECTION PIPE SUB-ASSEMBLY

Hide 87245A 6.CONNECT HEATER WATER HOSE SUB-ASSEMBLY