Home › Engine / Hybrid System › 2GD-FTV ENGINE CONTROL › ECD SYSTEM(w/ Urea SCR System) › from 2016.03
RM3250E _51 Engine / Hybrid System _038005 2GD-FTV ENGINE CONTROL _0262511 ECD SYSTEM(w/ Urea SCR System) C

2GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P205B  Reductant Tank Temperature Sensor Circuit Range/Performance  


DESCRIPTION

Refer to DTC P202B.

Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECD SYSTEM(w/ Urea SCR System)>P202B

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P205B Reductant Tank Temperature Sensor Circuit Range/Performance After the system has soaked for an appropriate length of time after the previous trip (while the engine coolant temperature has not yet increased after the engine has started), the temperature difference between the engine coolant and the urea solution (absolute value) is equal to or greater than a fixed value for 4 seconds or more (1 trip detection logic). Temperature sensor (urea pump) Comes on DTC stored

Related Data List
DTC No. Data List
P205B Reductant Pressure

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P205B After the engine has soaked for an appropriate length of time, start the engine and idle it for 4 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:
Handling the urea injector set
·

The urea injector set is a precision instrument. Take necessary precautions for installation and shipping. Do not use the part if it has been struck or dropped.

·

If the urea solution remaining inside the urea injector set dries out, it may become unable to inject urea solution. Therefore, conduct urea tube with heater assembly installation and removal quickly.

·

If the urea solution dries out and deposition occurs, urea may cling to the O-ring of the pipe and cause seal problems. Therefore, clean the urea tube with heater assembly and intake port of the urea injector set with water before attaching them.

·

Perform this procedure in an environment where urea solution will not freeze.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P205B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P205B is output A
DTC P205B and other DTCs are output* B


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.




A

2.CHECK AROUND BOTTOM OF VEHICLE

B

2.CHECK AROUND BOTTOM OF VEHICLE
a.

Check around the bottom of the vehicle.

HINT:

If the urea solution dries on an object, deposition occurs and leaves behind a white powder.


Area to check:

·

Areas connecting the urea pump and urea injector set.

·

Perforations in the urea tank sub-assembly.

·

Connectors not connected properly.

·

Clogging of the cooling fins of the urea injector set.

HINT:

If the cooling fins are clogged with foreign matter, remove the foreign matter and clean the cooling fins.




b.

Repair any trouble areas.


Result:
Proceed to
NEXT



NEXT

3.READ VALUE USING GTS (REDUCTANT TEMPERATURE)
3.READ VALUE USING GTS (REDUCTANT TEMPERATURE)
a.

Prepare a bucket or other receptacle for collecting urea solution.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pump Check (Backward).


e.

Perform the Active Test.

Powertrain > Engine > Active Test
Tester Display
Reductant Pump Check (Backward)
50004 234 322

f.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Purge.


g.

Perform the Active Test.

HINT:

Perform the Reductant Purge to draw the urea solution back into the urea tank sub-assembly from the urea injector set.


Powertrain > Engine > Active Test
Tester Display
Reductant Purge
50004 234 323

h.

After performing the Active Test, remove the urea tube with heater assembly from the urea injector set.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>UREA INJECTOR>REMOVAL

NOTICE:

If the urea solution remaining inside the urea injector set dries out, it may become unable to inject urea solution. Therefore, seal the urea injector set with an item such as a cover or rubber cap so that the inside does not dry out.



i.

Prepare a bucket or other receptacle for collecting urea solution from the urea tube with heater assembly.


j.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Discharge.


k.

Perform the Active Test.

Powertrain > Engine > Active Test
Tester Display
Reductant Discharge
50004 234 320

l.

According to the display on the GTS, perform the Active Test.

NOTICE:

When the Active Test is executed, urea solution will come out of the urea tube with heater assembly. Collect the urea solution with a bucket or other receptacle.



m.

After completing the Active Test, refill approximately 1 L of urea solution.

Click hereEngine / Hybrid System>2GD-FTV EMISSION CONTROL>UREA TANK>REFILL

HINT:

Check the temperature of the urea solution to be used for refilling.



n.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Temperature.


o.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display
Reductant Temperature
50003 234 1131
OK:

Within +/-5°C (9°F) of urea solution used for refilling.



Result:
Proceed to
OK
NG



OK

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

4.REPLACE UREA PUMP
4.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Stop the engine and allow it to soak.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Start the engine.


h.

Idle the engine for 4 seconds or more.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END