Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2016.03
RM3250E _58 Vehicle Interior _053993 PRE-CRASH SAFETY _0264409 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

The millimeter wave radar sensor assembly is connected to the forward recognition camera via CAN communication.

The millimeter wave radar sensor assembly operates the pre-crash alarm by sending a buzzer request signal to the skid control buzzer.

If the millimeter wave radar sensor assembly detects a malfunction in the skid control buzzer circuit, it stores DTC C1A4A.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit When the ignition switch to ON and the pre-crash alarm is operating, either of the following conditions is met:
·

A buzzer request signal is sent to the skid control buzzer but the buzzer does not sound for 0.3 seconds or more.

·

A buzzer request signal is not sent to the skid control buzzer but the buzzer sounds for 0.3 seconds or more.


·

Skid control buzzer

·

Forward recognition camera

·

Millimeter wave radar sensor assembly

·

Wire harness or connector



WIRING DIAGRAM

C355031E01
3.531,3.938 6.313,4.271 2.781,0.333 10 false Millimeter Wave Radar Sensor Assembly 4.802,1.635 6.625,2.208 1.823,0.573 10 false Forward Recognition Camera 4.521,1.635 4.979,1.833 0.458,0.198 10 false Q4 5.333,0.906 5.792,1.104 0.458,0.198 10 false BZ 5.115,0.76 5.573,0.958 0.458,0.198 10 false 8 3.229,1.26 4.531,1.656 1.302,0.396 10 false Skid Control Buzzer 2.833,1.271 3.292,1.469 0.458,0.198 10 false G129 3.969,0.906 4.427,1.104 0.458,0.198 10 false BZ 4.292,0.771 4.75,0.969 0.458,0.198 10 false 1 3.333,0.906 3.792,1.104 0.458,0.198 10 false IG1 3.083,0.76 3.542,0.958 0.458,0.198 10 false 2 2.125,1.073 2.844,1.344 0.719,0.271 10 false IG1 NO. 5 0.458,0.906 1.906,1.167 1.448,0.26 10 false from IG Circuit 0.604,4.354 2.583,4.625 1.979,0.271 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT

·

When a malfunction occurs in the communication line to the forward recognition camera, U023A and/or U1002 is output. If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>U023A



PROCEDURE

1.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON / OFF Test possible with ignition switch to ON
Vehicle condition: Vehicle stopped
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Crash Alarm Buzzer
50004 220 5

c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

B

2.CHECK TERMINAL VOLTAGE
2.CHECK TERMINAL VOLTAGE
a.
B443157C02
1.5,0.177 1.906,0.438 0.406,0.26 1.99,1.333 2.5,1.156 true 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.531,0.229 1.99,0.427 0.458,0.198 10 false G129 2.552,1.063 3.01,1.26 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer)


Disconnect the G129 skid control buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G129-2 (IG1) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Connect the G129 skid control buzzer connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - FORWARD RECOGNITION CAMERA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER - BATTERY)

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - FORWARD RECOGNITION CAMERA)
a.

Disconnect the G129 skid control buzzer connector.


b.

Disconnect the Q4 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G129-1 (BZ) - Q4-8 (BZ) Always Below 1 Ω
G129-1 (BZ) or Q4-8 (BZ) - Body ground Always 10 kΩ or higher



d.

Connect the Q4 forward recognition camera connector.


e.

Connect the G129 skid control buzzer connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER - FORWARD RECOGNITION CAMERA)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER - FORWARD RECOGNITION CAMERA)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
5.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON / OFF Test possible with ignition switch to ON
Vehicle condition: Vehicle stopped

c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B

6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)
6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)
a.

Turn the ignition switch to ON.


b.

Check if the skid control buzzer is sounding.


Result:
Result Proceed to
The skid control buzzer does not sound when the ignition switch to ON A
The skid control buzzer sounds continuously when the ignition switch to ON B



A

7.INSPECT SKID CONTROL BUZZER (UNIT INSPECTION)

B

8.REPLACE SKID CONTROL BUZZER
7.INSPECT SKID CONTROL BUZZER (UNIT INSPECTION)


Result:
Result Proceed to
Skid control buzzer is abnormal A
Skid control buzzer is normal B



A

8.REPLACE SKID CONTROL BUZZER

B

9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
8.REPLACE SKID CONTROL BUZZER

NEXT

9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON / OFF Test possible with ignition switch to ON
Vehicle condition: Vehicle stopped

c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END

B

10.REPLACE FORWARD RECOGNITION CAMERA
10.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform Forward Recognition Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
11.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON / OFF Test possible with ignition switch to ON
Vehicle condition: Vehicle stopped

c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

12.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
12.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC (PRE-CRASH SAFETY SYSTEM)
13.CLEAR DTC (PRE-CRASH SAFETY SYSTEM)
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

Result:
Proceed to
NEXT



NEXT

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)