Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.08
RM3250E _58 Vehicle Interior _038068 METER / GAUGE / DISPLAY _0184171 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the speedometer sensor*1 or brake actuator assembly (skid control ECU)*2.

*1: w/o ABS

*2: w/ ABS


WIRING DIAGRAM

E343437E02
0.521,1.531 2.146,1.938 1.625,0.406 10 false Brake Actuator Assembly (Skid Control ECU)*3 1.531,0.646 1.99,0.875 0.458,0.229 10 false SP1 1.99,0.75 2.448,0.979 0.458,0.229 10 false A4 1.927,0.552 2.385,0.781 0.458,0.229 10 false 14*1 2.427,0.76 2.885,0.99 0.458,0.229 10 false A3 2.375,0.542 2.833,0.771 0.458,0.229 10 false 22*2 2.594,2.75 4.219,3.156 1.625,0.406 10 false Speedomeer Sensor*4 2.594,2.604 3.083,2.833 0.49,0.229 10 false C62 3.542,1.75 4,1.979 0.458,0.229 10 false SI 3.771,1.75 4.229,1.979 0.458,0.229 10 false 3 5.427,0.635 5.885,0.865 0.458,0.229 10 false SI 5.177,0.646 5.635,0.875 0.458,0.229 10 false 18 5.406,3.792 5.865,4.021 0.458,0.229 10 false +S 5.135,3.781 5.594,4.01 0.458,0.229 10 false 19 5.073,4.229 5.531,4.458 0.458,0.229 10 false G9 5.094,4.375 6.917,4.656 1.823,0.281 10 false Combination Meter Assembly 1.74,3.885 2.229,4.115 0.49,0.229 10 false G88 2.167,3.885 2.656,4.115 0.49,0.229 10 false G45 2.583,3.885 3.073,4.115 0.49,0.229 10 false G85 3.021,3.885 3.51,4.115 0.49,0.229 10 false G83 1.708,3.656 2.198,3.885 0.49,0.229 10 false 12*5 2.156,3.646 2.646,3.875 0.49,0.229 10 false 23*6 2.583,3.646 3.073,3.875 0.49,0.229 10 false 10*7 2.99,3.646 3.479,3.875 0.49,0.229 10 false 17*8 0.833,4.302 1.406,4.531 0.573,0.229 10 false ECM*11 1.302,3.781 1.792,4.01 0.49,0.229 10 false SPD 0.844,6.135 1.448,6.365 0.604,0.229 10 false G120*12 1.323,5.604 1.813,5.833 0.49,0.229 10 false SP1 1.688,5.604 2.177,5.833 0.49,0.229 10 false 25 0.854,6.313 1.344,6.542 0.49,0.229 10 false ECM 5.604,6.135 6.094,6.365 0.49,0.229 10 false G27 5.625,6.302 6.625,6.51 1,0.208 10 false Body ECU*10 5.656,5.625 6.146,5.854 0.49,0.229 10 false SPD 5.469,5.615 5.958,5.844 0.49,0.229 10 false 5 5.26,7.844 5.75,8.073 0.49,0.229 10 false G69 5.271,8 6.802,8.354 1.531,0.354 10 false Certification ECU (Smart Key ECU Assembly)*9 5.667,7.458 6.156,7.688 0.49,0.229 10 false SPD 5.49,7.469 5.979,7.698 0.49,0.229 10 false 7 0.188,6.698 1.115,6.896 0.927,0.198 10 false *1: w/ VSC 0.188,7 1.115,7.198 0.927,0.198 10 false *2: w/o VSC 0.188,7.302 1.115,7.5 0.927,0.198 10 false *3: w/ ABS 0.188,7.698 1.115,7.896 0.927,0.198 10 false *4: w/o ABS 0.188,8 1.115,8.198 0.927,0.198 10 false *5: for 1GR-FE 0.188,8.323 1.792,8.542 1.604,0.219 10 false *6: for 1TR-FE, 2TR-FE 1.688,6.708 3.5,6.948 1.813,0.24 10 false *7: for 1GD-FTV, 2GD-FTV 1.698,7 3.51,7.24 1.813,0.24 10 false *8: for 1KD-FTV, 2KD-FTV 1.708,7.323 3.74,7.573 2.031,0.25 10 false *9: w/ Entry and Start System 1.708,7.698 3.74,7.948 2.031,0.25 10 false *10: w/ Body ECU 1.708,8 3.74,8.25 2.031,0.25 10 false *11: except 5L-E 1.708,8.313 3.74,8.563 2.031,0.25 10 false *12: for 5L-E

E353886E02
1.313,2.792 1.771,2.99 0.458,0.198 10 false SPD 1.313,0.948 1.771,1.146 0.458,0.198 10 false SPD 5.688,0.979 6.146,1.177 0.458,0.198 10 false SPD1 5.688,2.781 6.146,2.979 0.458,0.198 10 false SPD 1.719,0.958 2.031,1.156 0.313,0.198 10 false 17 1.719,2.813 2.031,3.01 0.313,0.198 10 false 17 5.438,2.802 5.75,3 0.313,0.198 10 false 17 5.427,0.958 5.74,1.156 0.313,0.198 10 false 25 0.521,1.5 1.135,1.698 0.615,0.198 10 false G113 0.479,1.667 5.063,1.865 4.583,0.198 10 false Navigation Receiver Assembly*2 0.5,3.323 0.958,3.521 0.458,0.198 10 false G37 0.469,3.479 3.063,3.708 2.594,0.229 10 false Radio and Display Receiver Assembly*3 6.052,1.479 6.51,1.677 0.458,0.198 10 false G90 6,1.646 6.771,1.844 0.771,0.198 10 false TCM*1 6.031,3.333 6.646,3.531 0.615,0.198 10 false G117 5.323,3.458 7.156,3.656 1.833,0.198 10 false Radio Receiver Assembly*4 5.51,5.313 7.135,5.552 1.625,0.24 10 false Telematics Transceiver*5 5.677,4.635 6.135,4.833 0.458,0.198 10 false SPDP 6.042,5.156 6.656,5.354 0.615,0.198 10 false G130 5.438,4.625 5.75,4.823 0.313,0.198 10 false 10 0.052,4.323 7.156,4.521 7.104,0.198 10 false *1: for 1KD-FTV, Automatic Transmission 0.052,4.615 3.719,4.813 3.667,0.198 10 false *2: w/ Navigation System 0.052,4.917 7.156,5.115 7.104,0.198 10 false *3: w/ Audio and Visual System (for Radio and Display Type) 0.052,5.208 7.156,5.406 7.104,0.198 10 false *4: w/ Audio and Visual System (for Radio Receiver Type) 0.052,5.49 3.719,5.688 3.667,0.198 10 false *5: w/ Telematics System

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

·

w/ Entry and Start System:

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

w/ Audio and Visual System (for Radio and Display Type):

When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PRECAUTION

·

If the body ECU has been replaced, it is necessary to initialize the body ECU.



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
NOTICE:

For vehicles without an entry and start system, go to "Check Body ECU".


*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Body ECU

*6: for 1KD-FTV, Automatic Transmission

*7: w/ Navigation System

*8: w/ Audio and Visual System (for Radio and Display Type)

*9: w/ Audio and Visual System (for Radio Receiver Type)

*10: for 5L-E

*11: w/ Telematics System


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*10 ECM connector.


c.

Disconnect the G27 body ECU connector.*5


d.

Disconnect the G90 TCM connector.*6


e.

Disconnect the G113 navigation receiver assembly connector.*7


f.

Disconnect the G37 radio and display receiver assembly connector.*8


g.

Disconnect the G117 radio receiver assembly connector.*9


h.

Disconnect the G130 telematics transceiver connector.*11


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK BODY ECU

NG

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
2.CHECK BODY ECU
NOTICE:

For vehicles without a body ECU, go to "Check TCM".


*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: for 1KD-FTV, Automatic Transmission

*7: w/ Navigation System

*8: w/ Audio and Visual System (for Radio and Display Type)

*9: w/ Audio and Visual System (for Radio Receiver Type)

*10: for 5L-E

*11: w/ Telematics System


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*10 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G90 TCM connector.*6


e.

Disconnect the G113 navigation receiver assembly connector.*7


f.

Disconnect the G37 radio and display receiver assembly connector.*8


g.

Disconnect the G117 radio receiver assembly connector.*9


h.

Disconnect the G130 telematics transceiver connector.*11


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK TCM

NG

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)
3.CHECK TCM
NOTICE:

For vehicles without a KD series engine, automatic transmission, go to "Check Navigation Receiver Assembly".


*1: w/ Entry and Start System

*2: w/ Body ECU

*3: w/ Navigation System

*4: w/ Audio and Visual System (for Radio and Display Type)

*5: w/ Audio and Visual System (for Radio Receiver Type)

*6: w/ Telematics System


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G83 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1


d.

Disconnect the G27 body ECU connector.*2


e.

Disconnect the G113 navigation receiver assembly connector.*3


f.

Disconnect the G37 radio and display receiver assembly connector.*4


g.

Disconnect the G117 radio receiver assembly connector.*5


h.

Disconnect the G130 telematics transceiver connector.*6


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
4.CHECK NAVIGATION RECEIVER ASSEMBLY
NOTICE:

For vehicles without a navigation system, go to "Check Radio and Display Receiver Assembly".


*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for 1KD-FTV, Automatic Transmission

*8: for 5L-E

*9: w/ Telematics System


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*8 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Disconnect the G130 telematics transceiver connector.*9


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
5.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
NOTICE:

For vehicles without an audio and visual system (for radio and display type), go to "Check Radio Receiver Assembly".


*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for 1KD-FTV, Automatic Transmission

*8: for 5L-E

*9: w/ Telematics System


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3 G83*4 or G120*8 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Disconnect the G130 telematics transceiver connector.*9


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK RADIO RECEIVER ASSEMBLY

NG

16.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
6.CHECK RADIO RECEIVER ASSEMBLY
NOTICE:

For vehicles without an audio and visual system (for radio receiver type), go to "Check ECM".


*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for 1KD-FTV, Automatic Transmission

*8: for 5L-E

*9: w/ Telematics System


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*8 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Disconnect the G130 telematics transceiver connector.*9


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK ECM

NG

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)
7.CHECK ECM

*1: w/ Entry and Start System

*2: w/ Body ECU

*3: for 1KD-FTV, Automatic Transmission

*4: w/ Navigation System

*5: w/ Audio and Visual System (for Radio and Display Type)

*6: w/ Audio and Visual System (for Radio Receiver Type)

*7: w/ Telematics System


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1


c.

Disconnect the G27 body ECU connector.*2


d.

Disconnect the G90 TCM connector.*3


e.

Disconnect the G113 navigation receiver assembly connector.*4


f.

Disconnect the G37 radio and display receiver assembly connector.*5


g.

Disconnect the G117 radio receiver assembly connector.*6


h.

Disconnect the G130 telematics transceiver connector.*7


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK TELEMATICS TRANSCEIVER

NG

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
8.CHECK TELEMATICS TRANSCEIVER
NOTICE:

For vehicles without a telematics system, go to "Check Veicle Type"


*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: w/ Entry and Start System

*4: w/ Body ECU

*5: w/ Audio and Visual System (for Radio and Display Type)

*6: w/ Audio and Visual System (for Radio Receiver Type)


a.
C240157C56
1.51,0.271 1.927,0.469 0.417,0.198 0.635,0.948 0.833,0.948 0.833,0.948 1.052,1.115 true 0.146,0.083 0.458,0.24 0.313,0.156 10 false *a 1.625,0.281 1.938,0.438 0.313,0.156 10 false G9 0.417,0.823 0.844,1.01 0.427,0.188 10 false +S
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Disconnect the G45*1, G85*2, ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*3


d.

Disconnect the G27 body ECU connector.*4


e.

Disconnect the G37 radio and display receiver assembly connector.*5


f.

Disconnect the G117 radio receiver assembly connector.*6


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK VEHICLE TYPE

NG

19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TELEMATICS TRANSCEIVER)
9.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ ABS A
w/o ABS B



A

10.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

B

20.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
10.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.
C317099C04
1.448,2.479 1.896,2.771 0.448,0.292 1.458,0.125 1.906,0.417 0.448,0.292 0.51,1.729 0.688,1.729 0.688,1.729 1.094,1.021 true 2.531,4.406 2.344,4.406 2.344,4.406 1.958,3.594 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 2.604,4.313 3.219,4.51 0.615,0.198 10 false SP1 1.604,0.177 1.917,0.375 0.313,0.198 10 false A4 1.594,2.531 1.906,2.729 0.313,0.198 10 false A3 1.979,0.198 2.292,0.396 0.313,0.198 10 false *A 1.958,2.542 2.271,2.74 0.313,0.198 10 false *B 0.177,1.594 0.792,1.792 0.615,0.198 10 false SP1
*A w/ VSC
*B w/o VSC
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ VSC
Tester Connection Switch Condition Specified Condition
A4-14 (SP1) - Body ground Ignition switch ON 11 to 14 V

w/o VSC
Tester Connection Switch Condition Specified Condition
A3-22 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

21.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
11.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E200403C12
1.521,0.26 1.917,0.479 0.396,0.219 1.052,1.125 0.771,0.865 0.771,0.865 0.615,0.865 true 0.406,0.76 0.708,1.073 0.302,0.313 10 false SI 1.625,0.281 1.99,0.469 0.365,0.188 10 false G9 1.333,4.094 1.458,4.24 0.125,0.146 10 false A 2.969,3.51 3.427,3.885 0.458,0.375 10 false GND 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.094,2.448 0.406,2.604 0.313,0.156 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Connect an oscilloscope to terminal G9-18 (SI) and body ground.


c.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G9-18 (SI) - Body ground
Tool Setting 5 V/DIV, 20 ms./DIV
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Body ECU

*6: for 1KD-FTV, Automatic Transmission

*7: w/ Navigation System

*8: w/ Audio and Visual System (for Radio and Display Type)

*9: w/ Audio and Visual System (for Radio Receiver Type)

*10: for 5L-E

*11: w/ Telematics System


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*10 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G27 body ECU connector.*5


e.

Disconnect the G90 TCM connector.*6


f.

Disconnect the G113 navigation receiver assembly connector.*7


g.

Disconnect the G37 radio and display receiver assembly connector.*8


h.

Disconnect the G117 radio receiver assembly connector.*9


i.

Disconnect the G130 telematics transceiver connector.*11


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G69-7 (SPD) Always Below 1 Ω
G9-19 (+S) or G69-7 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY ECU)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: for 1KD-FTV, Automatic Transmission

*7: w/ Navigation System

*8: w/ Audio and Visual System (for Radio and Display Type)

*9: w/ Audio and Visual System (for Radio Receiver Type)

*10: for 5L-E

*11: w/ Telematics System


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*10 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.


e.

Disconnect the G90 TCM connector.*6


f.

Disconnect the G113 navigation receiver assembly connector.*7


g.

Disconnect the G37 radio and display receiver assembly connector.*8


h.

Disconnect the G117 radio receiver assembly connector.*9


i.

Disconnect the G130 telematics transceiver connector.*11


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G27-5 (SPD) Always Below 1 Ω
G9-19 (+S) or G27-5 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)

*1: w/ Entry and Start System

*2: w/ Body ECU

*3: w/ Navigation System

*4: w/ Audio and Visual System (for Radio and Display Type)

*5: w/ Audio and Visual System (for Radio Receiver Type)

*6: w/ Telematics System


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G83 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*1


d.

Disconnect the G27 body ECU connector.*2


e.

Disconnect the G90 TCM connector.


f.

Disconnect the G113 navigation receiver assembly connector.*3


g.

Disconnect the G37 radio and display receiver assembly connector.*4


h.

Disconnect the G117 radio receiver assembly connector.*5


i.

Disconnect the G130 telematics transceiver connector.*6


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G90-25 (SPD1) Always Below 1 Ω
G9-19 (+S) or G90-25 (SPD1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for 1KD-FTV, Automatic Transmission

*8: for 5L-E

*9: w/ Telematics System


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*8 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Disconnect the G113 navigation receiver assembly connector.


g.

Disconnect the G130 telematics transceiver connector.*9


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G113-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G113-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for 1KD-FTV, Automatic Transmission

*8: for 5L-E

*9: w/ Telematics System


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*8 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Disconnect the G37 radio and display receiver assembly connector.


g.

Disconnect the G130 telematics transceiver connector.*9


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G37-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G37-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO RECEIVER ASSEMBLY)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for 1KD-FTV, Automatic Transmission

*8: for 5L-E

*9: w/ Telematics System


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*8 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Disconnect the G117 radio receiver assembly connector.


g.

Disconnect the G130 telematics transceiver connector.*9


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G117-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G117-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Body ECU

*7: for 1KD-FTV, Automatic Transmission

*8: w/ Navigation System

*9: w/ Audio and Visual System (for Radio and Display Type)

*10: w/ Audio and Visual System (for Radio Receiver Type)

*11: for 5L-E

*12: w/ Telematics System


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G88*1, G45*2, G85*3, G83*4 or G120*11 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


d.

Disconnect the G27 body ECU connector.*6


e.

Disconnect the G90 TCM connector.*7


f.

Disconnect the G113 navigation receiver assembly connector.*8


g.

Disconnect the G37 radio and display receiver assembly connector.*9


h.

Disconnect the G117 radio receiver assembly connector.*10


i.

Disconnect the G130 telematics transceiver connector.*12


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE
Tester Connection Condition Specified Condition
G9-19 (+S) - G88-12 (SPD) Always Below 1 Ω
G9-19 (+S) or G88-12 (SPD) - Body ground Always 10 kΩ or higher

for 1TR-FE, 2TR-FE
Tester Connection Condition Specified Condition
G9-19 (+S) - G45-23 (SPD) Always Below 1 Ω
G9-19 (+S) or G45-23 (SPD) - Body ground Always 10 kΩ or higher

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Specified Condition
G9-19 (+S) - G85-10 (SPD) Always Below 1 Ω
G9-19 (+S) or G85-10 (SPD) - Body ground Always 10 kΩ or higher

for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G9-19 (+S) - G83-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G83-17 (SPD) - Body ground Always 10 kΩ or higher

for 5L-E
Tester Connection Condition Specified Condition
G9-19 (+S) - G120-25 (SP1) Always Below 1 Ω
G9-19 (+S) or G120-25 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TELEMATICS TRANSCEIVER)

*1: for 2TR-FE

*2: for 1GD-FTV, 2GD-FTV

*3: w/ Entry and Start System

*4: w/ Body ECU

*5: w/ Audio and Visual System (for Radio and Display Type)

*6: w/ Audio and Visual System (for Radio Receiver Type)


a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G45*1 or G85*2 ECM connector.


c.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*3


d.

Disconnect the G27 body ECU connector.*4


e.

Disconnect the G37 radio and display receiver assembly connector.*5


f.

Disconnect the G117 radio receiver assembly connector.*6


g.

Disconnect the G130 telematics transceiver connector.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G130-10 (SPDP) Always Below 1 Ω
G9-19 (+S) or G130-10 (SPDP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E200403C12
1.521,0.26 1.917,0.479 0.396,0.219 1.052,1.125 0.771,0.865 0.771,0.865 0.615,0.865 true 0.406,0.76 0.708,1.073 0.302,0.313 10 false SI 1.625,0.281 1.99,0.469 0.365,0.188 10 false G9 1.333,4.094 1.458,4.24 0.125,0.146 10 false A 2.969,3.51 3.427,3.885 0.458,0.375 10 false GND 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.094,2.448 0.406,2.604 0.313,0.156 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Connect an oscilloscope to terminal G9-18 (SI) and body ground.


c.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G9-18 (SI) - Body ground
Tool Setting 5 V/DIV, 20 ms./DIV
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

22.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
21.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the A4*1 or A3*2 brake actuator assembly (skid control ECU) connector.

*1: w/ VSC

*2: w/o VSC



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ VSC
Tester Connection Condition Specified Condition
G9-18 (SI) - A4-14 (SP1) Always Below 1 Ω
G9-18 (SI) or A4-14 (SP1) - Body ground Always 10 kΩ or higher

w/o VSC
Tester Connection Condition Specified Condition
G9-18 (SI) - A3-22 (SP1) Always Below 1 Ω
G9-18 (SI) or A3-22 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the C62 speedometer sensor connector.


b.

Disconnect the G9 and G10 combination meter assembly connectors.


c.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C62-3 (SI) - G9-18 (SI) Always Below 1 Ω
C62-3 (SI) or G9-18 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR