Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) › from 2016.08
RM3250E _57 Power Source / Network _038063 NETWORKING _0262515 CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)  Short to B+ in CAN Bus Line  


DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom Trouble Area

*1: w/ VSC

*2: for Automatic Air Conditioning System or for Manual Air Conditioning System

*3: w/ Entry and Start System

*4: for 4WD

*5: w/ Audio and Visual System (for Radio and Display Type)

*6: w/ Navigation System

*7: for LED Headlight or w/ Headlight Cleaner System

*8: w/ Airbag System

*9: w/ Stop and Start System

*10: w/ Telematics Transceiver

The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
·

Short between CAN bus lines and +B

·

ECM

·

Brake actuator assembly (skid control ECU)

·

Spiral with sensor cable sub-assembly (steering angle sensor)*1

·

Air conditioning amplifier assembly*2

·

Airbag sensor assembly*8

·

Certification ECU (smart key ECU assembly)*3

·

4 wheel drive control ECU*4

·

Radio and display receiver assembly*5

·

Navigation receiver assembly*6

·

Headlight leveling ECU assembly*7

·

Engine stop and start ECU*9

·

Telematics transceiver*10

·

Combination meter assembly

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C348143E01
6.063,0.177 6.542,0.354 0.479,0.177 10 false CANH 6.063,0.958 6.542,1.135 0.479,0.177 10 false CANL 6.021,2.344 6.5,2.521 0.479,0.177 10 false CANH 6.031,2.875 6.51,3.052 0.479,0.177 10 false CANL 0.875,0.302 1.354,0.479 0.479,0.177 10 false CANH 0.885,0.844 1.365,1.021 0.479,0.177 10 false CANL 0.885,2.354 1.365,2.531 0.479,0.177 10 false CANH 0.885,2.854 1.365,3.031 0.479,0.177 10 false CANL 1.021,4.677 1.354,4.844 0.333,0.167 10 false TX+ 1.031,5.198 1.365,5.365 0.333,0.167 10 false TX- 6.01,4.698 6.49,4.875 0.479,0.177 10 false CANP 6.052,5.229 6.531,5.406 0.479,0.177 10 false CANN 4.354,0.833 4.833,1.01 0.479,0.177 10 false G45 4.365,0.313 4.844,0.49 0.479,0.177 10 false G45 4.75,0.302 5.229,0.479 0.479,0.177 10 false G85 4.771,0.833 5.25,1.01 0.479,0.177 10 false G85 5.177,0.302 5.656,0.479 0.479,0.177 10 false G83 5.167,0.844 5.646,1.021 0.479,0.177 10 false G83 5.563,0.302 6.042,0.479 0.479,0.177 10 false G121 5.573,0.833 6.052,1.01 0.479,0.177 10 false G121 4.333,0.104 4.813,0.26 0.479,0.156 10 false 13*1 4.74,0.104 5.219,0.26 0.479,0.156 10 false 17*2 5.167,0.104 5.646,0.26 0.479,0.156 10 false 24*3 5.563,0.104 6.042,0.26 0.479,0.156 10 false 25*10 4.323,0.635 4.802,0.792 0.479,0.156 10 false 14*1 4.74,0.635 5.219,0.792 0.479,0.156 10 false 28*2 5.167,0.635 5.646,0.792 0.479,0.156 10 false 23*3 5.542,0.635 6.021,0.792 0.479,0.156 10 false 31*10 3.583,0.198 3.844,0.375 0.26,0.177 10 false 5 3.594,0.698 3.854,0.875 0.26,0.177 10 false 15 6.188,1.313 6.667,1.49 0.479,0.177 10 false ECM 2.635,0.177 2.896,0.354 0.26,0.177 10 false 3 2.573,0.698 2.833,0.875 0.26,0.177 10 false 13 1.448,0.177 1.708,0.354 0.26,0.177 10 false 40 1.448,0.719 1.708,0.896 0.26,0.177 10 false 18 0.104,1.177 1.938,1.552 1.833,0.375 10 false G70 0.104,1.354 1.938,1.729 1.833,0.375 10 false Certification ECU (Smart Key ECU Assembly)*4 3.635,2.219 3.896,2.396 0.26,0.177 10 false 4 3.594,2.74 3.854,2.917 0.26,0.177 10 false 14 5.698,2.229 5.958,2.406 0.26,0.177 10 false 20 5.688,2.76 5.948,2.938 0.26,0.177 10 false 40 5.333,3.323 7.156,3.542 1.823,0.219 10 false 4 Wheel Drive Control ECU*7 5.323,3.156 7.146,3.375 1.823,0.219 10 false C39 2.656,2.219 2.917,2.396 0.26,0.177 10 false 7 2.583,2.75 2.844,2.927 0.26,0.177 10 false 17 1.854,2.354 2.333,2.531 0.479,0.177 10 false G113 1.844,2.875 2.323,3.052 0.479,0.177 10 false G113 1.448,2.354 1.927,2.531 0.479,0.177 10 false G37 1.458,2.885 1.938,3.063 0.479,0.177 10 false G37 1.469,2.135 1.948,2.292 0.479,0.156 10 false 9*5 1.875,2.146 2.354,2.302 0.479,0.156 10 false 9*6 1.417,2.677 1.896,2.833 0.479,0.156 10 false 10*5 1.854,2.688 2.333,2.844 0.479,0.156 10 false 10*6 0.042,3.313 2.563,3.75 2.521,0.438 10 false Radio and Display Receiver Assembly*5, Navigation Receiver Assembly*6 3.625,4.563 3.885,4.74 0.26,0.177 10 false 9 3.583,5.104 3.844,5.281 0.26,0.177 10 false 19 3.625,5.667 3.885,5.844 0.26,0.177 10 false 6 3.583,6.219 3.844,6.396 0.26,0.177 10 false 16 2.563,4.573 2.823,4.75 0.26,0.177 10 false 10 2.552,5.104 2.813,5.281 0.26,0.177 10 false 20 1.885,4.677 2.365,4.854 0.479,0.177 10 false G77 1.875,5.229 2.354,5.406 0.479,0.177 10 false G77 1.438,4.688 1.917,4.865 0.479,0.177 10 false G33 1.458,5.229 1.938,5.406 0.479,0.177 10 false G33 1.427,4.469 1.906,4.625 0.479,0.156 10 false 11*8 1.896,4.469 2.375,4.625 0.479,0.156 10 false 8*9 1.427,5 1.906,5.156 0.479,0.156 10 false 12*8 1.885,5.01 2.365,5.167 0.479,0.156 10 false 9*9 0.01,5.698 2.458,5.927 2.448,0.229 10 false Air Conditioning Amplifier Assembly 2.49,6.917 4.448,7.135 1.958,0.219 10 false No. 2 CAN Junction Connector 2.469,6.76 4.427,6.979 1.958,0.219 10 false G68 5.708,4.573 5.969,4.75 0.26,0.177 10 false 15 5.708,5.094 5.969,5.271 0.26,0.177 10 false 16 5.417,5.688 7.146,5.906 1.729,0.219 10 false Telematics Transceiver*11 5.427,5.521 7.156,5.74 1.729,0.219 10 false G130 0.083,6.667 2.042,6.885 1.958,0.219 10 false *1: for 1TR-FE, 2TR-FE 0.083,7.042 2.042,7.26 1.958,0.219 10 false *2: for 1GD-FTV, 2GD-FTV 0.083,7.365 2.042,7.583 1.958,0.219 10 false *3: for 1KD-FTV, 2KD-FTV 0.115,7.74 2.073,7.958 1.958,0.219 10 false *4: w/ Entry and Start System 0.125,8.094 3.844,8.385 3.719,0.292 10 false *5: w/ Audio and Visual System (for Radio and Display Type) 0.115,8.479 3.833,8.771 3.719,0.292 10 false *6: w/ Navigation System 3.896,7.313 6.167,7.573 2.271,0.26 10 false *7: for 4WD 3.875,7.948 6.625,8.156 2.75,0.208 10 false *9: for Manual Air Conditioning System 3.865,7.635 6.615,7.844 2.75,0.208 10 false *8: for Automatic Air Conditioning System 3.875,8.25 6.625,8.458 2.75,0.208 10 false *10: for 5L-E 3.875,8.552 6.625,8.76 2.75,0.208 10 false *11: w/ Telematics Transceiver

C348076E01
4.146,0.458 4.302,0.656 0.156,0.198 10 false 6 4.125,0.76 4.438,0.958 0.313,0.198 10 false 16 4.146,1.177 4.302,1.375 0.156,0.198 10 false 1 4.146,1.708 4.458,1.906 0.313,0.198 10 false 11 5.156,1.063 5.583,1.354 0.427,0.292 10 false 25*1 5.594,1.063 6.021,1.354 0.427,0.292 10 false 22*2 5.583,1.573 6.01,1.865 0.427,0.292 10 false 10*2 5.146,1.573 5.573,1.865 0.427,0.292 10 false 14*1 5.219,1.292 5.625,1.542 0.406,0.25 10 false A3 5.229,1.823 5.635,2.073 0.406,0.25 10 false A3 5.656,1.813 6.063,2.063 0.406,0.25 10 false A4 5.646,1.292 6.052,1.542 0.406,0.25 10 false A4 6.021,1.292 6.521,1.51 0.5,0.219 10 false CANH 6.021,1.823 6.521,2.042 0.5,0.219 10 false CANL 3.156,1.135 3.313,1.333 0.156,0.198 10 false 2 3.094,1.667 3.406,1.865 0.313,0.198 10 false 12 1.438,1.135 1.75,1.333 0.313,0.198 10 false 13 1.448,1.646 1.76,1.844 0.313,0.198 10 false 22 0.865,1.292 1.365,1.51 0.5,0.219 10 false CANH 0.885,1.813 1.385,2.031 0.5,0.219 10 false CANL 5.479,2.24 7.115,2.656 1.635,0.417 10 false Brake Actuator Assembly (Skid Control ECU) 0.094,2.292 2.448,2.688 2.354,0.396 10 false Airbag Sensor Assembly*4 4.167,3.01 4.323,3.208 0.156,0.198 10 false 3 4.156,3.521 4.469,3.719 0.313,0.198 10 false 13 3.135,3.01 3.292,3.208 0.156,0.198 10 false 4 3.104,3.521 3.417,3.719 0.313,0.198 10 false 14 5.75,3.01 5.906,3.208 0.156,0.198 10 false 3 5.729,3.531 5.885,3.729 0.156,0.198 10 false 2 6.01,3.156 6.51,3.375 0.5,0.219 10 false CANH 6.052,3.708 6.552,3.927 0.5,0.219 10 false CANL 0.083,2.104 2.438,2.5 2.354,0.396 10 false G42 4.698,3.958 7.052,4.354 2.354,0.396 10 false G21 4.708,4.156 7.156,4.583 2.448,0.427 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)*2 1.458,3.542 1.771,3.74 0.313,0.198 10 false 14 1.469,3.01 1.625,3.208 0.156,0.198 10 false 6 0.906,3.146 1.406,3.365 0.5,0.219 10 false CANH 0.917,3.708 1.417,3.927 0.5,0.219 10 false CANL 0.792,4.156 3.146,4.552 2.354,0.396 10 false G8 0.74,4.344 3.094,4.74 2.354,0.396 10 false DLC3 4.167,7.198 4.323,7.396 0.156,0.198 10 false 5 4.167,7.75 4.479,7.948 0.313,0.198 10 false 15 6.021,7.24 6.521,7.458 0.5,0.219 10 false CANH 6.052,8.063 6.552,8.281 0.5,0.219 10 false CANL 5.656,7.219 5.969,7.417 0.313,0.198 10 false 36 5.646,7.75 5.958,7.948 0.313,0.198 10 false 35 5.219,8.323 7.156,8.615 1.938,0.292 10 false Combination Meter Assembly 5.219,8.177 7.156,8.469 1.938,0.292 10 false G9 3.135,5.115 3.292,5.313 0.156,0.198 10 false 8 3.104,5.635 3.417,5.833 0.313,0.198 10 false 18 1.458,5.083 1.615,5.281 0.156,0.198 10 false 6 1.448,5.646 1.604,5.844 0.156,0.198 10 false 7 0.854,5.271 1.354,5.49 0.5,0.219 10 false CANH 0.917,5.781 1.417,6 0.5,0.219 10 false CANL 0.042,6.24 2.625,6.5 2.583,0.26 10 false Headlight Leveling ECU Assembly*3 0.042,6.083 2.625,6.344 2.583,0.26 10 false G80 4.167,5.135 4.323,5.333 0.156,0.198 10 false 7 4.146,5.656 4.458,5.854 0.313,0.198 10 false 17 5.667,5.125 5.979,5.323 0.313,0.198 10 false 13 5.677,5.646 5.99,5.844 0.313,0.198 10 false 14 6,5.25 6.5,5.469 0.5,0.219 10 false CANH 6.031,5.802 6.531,6.021 0.5,0.219 10 false CANL 5.25,6.219 7.156,6.458 1.906,0.24 10 false Engine Stop and Start ECU*5 5.25,6.063 7.156,6.302 1.906,0.24 10 false G127 2.844,8.198 4.781,8.49 1.938,0.292 10 false No. 1 CAN Junction Connector 2.833,8.031 4.771,8.323 1.938,0.292 10 false G67 0.094,6.729 2.677,6.99 2.583,0.26 10 false *1: w/o VSC 0.125,7.115 2.708,7.375 2.583,0.26 10 false *2: w/ VSC 0.125,7.448 2.365,7.813 2.24,0.365 10 false *3: for LED Headlight or w/ Headlight Cleaner System 0.125,8.073 2.417,8.354 2.292,0.281 10 false *4: w/ Airbag System 0.135,8.406 2.427,8.688 2.292,0.281 10 false *5: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

Type C:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION

·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the service bulletin.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

·

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION



PROCEDURE

1.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
a.
C300827C25
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 1.552,0.385 1.552,0.385 1.406,0.385 true 1.938,1.49 1.781,1.906 1.781,1.906 1.594,1.906 true 2.313,1.49 2.51,1.906 2.51,1.906 2.646,1.906 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.219,1.042 0.469,1.219 0.25,0.177 10 false G8 1,0.333 1.49,0.479 0.49,0.146 10 false CANH 1.25,1.833 1.865,2.031 0.615,0.198 10 false CANL 2.719,1.844 3.063,2 0.344,0.156 10 false BAT
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-6 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G8-14 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

2.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR SIDE)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR SIDE)
a.
C300827C25
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 1.552,0.385 1.552,0.385 1.406,0.385 true 1.938,1.49 1.781,1.906 1.781,1.906 1.594,1.906 true 2.313,1.49 2.51,1.906 2.51,1.906 2.646,1.906 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.219,1.042 0.469,1.219 0.25,0.177 10 false G8 1,0.333 1.49,0.479 0.49,0.146 10 false CANH 1.25,1.833 1.865,2.031 0.615,0.198 10 false CANL 2.719,1.844 3.063,2 0.344,0.156 10 false BAT
*a Front view of DLC3


Disconnect the No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-6 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G8-14 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)

NG

27.CONNECT CONNECTOR
4.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

C348063C16
1.813,0.563 2.333,0.865 0.521,0.302 5.24,0.417 5.76,0.719 0.521,0.302 1.5,1.406 0.99,0.802 0.99,0.802 0.823,0.802 true 1.51,1.573 0.969,2.104 0.969,2.104 0.802,2.104 true 2.385,1.417 3.052,0.385 3.052,0.385 3.208,0.385 true 2.406,1.552 3.115,2.542 3.115,2.542 3.271,2.542 true 6.104,1.74 6.344,2.198 6.344,2.198 6.5,2.198 true 1.698,1.563 1.115,2.323 1.115,2.323 0.948,2.323 true 1.688,1.417 1.115,0.615 1.115,0.615 0.948,0.615 true 1.844,1.417 1.208,0.427 1.208,0.427 1.042,0.427 true 1.854,1.573 1.229,2.521 1.229,2.521 1.063,2.521 true 2.771,1.552 3.365,2.354 3.365,2.354 3.521,2.354 true 2.771,1.417 3.333,0.573 3.333,0.573 3.49,0.573 true 2.969,1.427 3.438,0.792 3.438,0.792 3.594,0.792 true 2.979,1.563 3.469,2.188 3.469,2.188 3.625,2.188 true 1.938,0.625 2.552,0.823 0.615,0.198 10 false G68 5.406,0.49 6.021,0.688 0.615,0.198 10 false G8 0.281,0.708 1.198,0.906 0.917,0.198 10 false CANH*c 0.396,0.521 1.313,0.719 0.917,0.198 10 false CANH*d 3.531,0.5 4.448,0.698 0.917,0.198 10 false CANH*g 0.49,0.323 1.406,0.521 0.917,0.198 10 false CANH*e 0.292,2 1.208,2.198 0.917,0.198 10 false CANL*c 0.427,2.25 1.344,2.448 0.917,0.198 10 false CANL*d 0.521,2.438 1.438,2.635 0.917,0.198 10 false CANL*e 3.563,2.271 4.479,2.469 0.917,0.198 10 false CANL*g 0.135,0.104 1.052,0.302 0.917,0.198 10 false *a 4.146,0.135 5.063,0.333 0.917,0.198 10 false *b 6.594,2.115 7,2.51 0.406,0.396 10 false BAT 3.25,0.313 4.167,0.51 0.917,0.198 10 false CANH*f 3.323,2.469 4.24,2.667 0.917,0.198 10 false CANL*f 3.688,2.115 4.604,2.313 0.917,0.198 10 false CANL*h 3.635,0.719 4.552,0.917 0.917,0.198 10 false CANH*h
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b Front view of DLC3
*c to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *d to 4 Wheel Drive Control ECU (for 4WD)
*e to ECM *f
·

to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])

·

to Navigation Receiver Assembly (w/ Navigation System)


*g to Telematics Transceiver (w/ Telematics Transceiver) *h
·

to Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System)

·

to Air Conditioning Amplifier Assembly (for Manual Air Conditioning System)




Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Entry and Start System

*2: for 4WD

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: w/ Navigation System

*5: for Automatic Air Conditioning System

*6: for Manual Air Conditioning System

*7: w/ Telematics Transceiver

G68-3 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Certification ECU (Smart Key ECU Assembly)*1
G68-13 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G68-4 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher 4 Wheel Drive Control ECU*2
G68-14 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G68-5 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
G68-15 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G68-7 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
·

Radio and Display Receiver Assembly*3

·

Navigation Receiver Assembly*4


G68-17 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G68-9 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Telematics Transceiver*7
G68-19 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G68-10 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Air Conditioning Amplifier Assembly*5, *6
G68-20 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Result Proceed to
OK A
NG (to certification ECU [smart key ECU assembly] CAN branch wire) (w/ Entry and Start System) B
NG (to 4 wheel drive control ECU CAN branch wire) (for 4WD) C
NG (to ECM CAN main wire) (for 1TR-FE, 2TR-FE) D
NG (to ECM CAN main wire) (for 1KD-FTV, 2KD-FTV) E
NG (to ECM CAN main wire) (for 1GD-FTV, 2GD-FTV) F
NG (to ECM CAN main wire) (for 5L-E) G
NG (to radio and display receiver assembly CAN branch wire) (w/ Audio and Visual System [for Radio and Display Type]) H
NG (to navigation receiver assembly CAN branch wire) (w/ Navigation System) I
NG (to telematics transceiver CAN branch wire) (w/ Telematics Transceiver) J
NG (to air conditioning amplifier assembly CAN branch wire) (for Automatic Air Conditioning System) K
NG (to air conditioning amplifier assembly CAN branch wire) (for Manual Air Conditioning System) L



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

5.CONNECT CONNECTOR

C

7.CONNECT CONNECTOR

D

9.CONNECT CONNECTOR

E

11.CONNECT CONNECTOR

F

13.CONNECT CONNECTOR

G

15.CONNECT CONNECTOR

H

17.CONNECT CONNECTOR

I

19.CONNECT CONNECTOR

J

21.CONNECT CONNECTOR

K

23.CONNECT CONNECTOR

L

25.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CERTIFICATION ECU BRANCH WIRE)
6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CERTIFICATION ECU BRANCH WIRE)
a.
C317104C03
1.417,2.521 1.896,2.813 0.479,0.292 1.458,0.125 1.938,0.417 0.479,0.292 2.594,4.354 2.438,4.354 2.438,4.354 2.354,3.802 true 3.094,1.052 2.833,0.427 2.833,0.427 2.677,0.427 true 3.063,1.26 2.875,2 2.875,2 2.719,2 true 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a 0.094,2.438 0.406,2.594 0.313,0.156 10 false *b 1.573,0.188 2.031,0.385 0.458,0.198 10 false G70 1.573,2.583 2.031,2.781 0.458,0.198 10 false G8 2.688,4.25 3.146,4.448 0.458,0.198 10 false BAT 2.281,1.927 2.771,2.188 0.49,0.26 10 false CANH 2.26,0.365 2.698,0.625 0.438,0.26 10 false CANL
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])
*b Front view of DLC3


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-40 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G70-18 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

7.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (4 WHEEL DRIVE CONTROL ECU BRANCH WIRE)
8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (4 WHEEL DRIVE CONTROL ECU BRANCH WIRE)
a.
C317105C03
1.458,0.198 1.917,0.469 0.458,0.271 1.344,2.552 1.802,2.823 0.458,0.271 2.948,1.198 2.833,0.531 2.833,0.531 2.677,0.531 true 2.635,4.271 2.5,4.271 2.5,4.271 2.344,3.802 true 2.948,1.438 2.875,2.021 2.875,2.021 2.719,2.021 true 0.073,0.042 0.385,0.198 0.313,0.156 10 false *a 0.125,2.521 0.438,2.677 0.313,0.156 10 false *b 1.563,0.25 2.021,0.448 0.458,0.198 10 false C39 1.5,2.615 1.958,2.813 0.458,0.198 10 false G8 2.313,1.948 2.74,2.208 0.427,0.26 10 false CANL 2.24,0.469 2.677,0.76 0.438,0.292 10 false CANH 2.729,4.188 3.344,4.385 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)
*b Front view of DLC3


Disconnect the 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-20 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C39-40 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4 WHEEL DRIVE CONTROL ECU (CANH, CANL)

9.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
a.
C317106C09
0.094,0.906 0.521,1.208 0.427,0.302 1.448,2.542 1.875,2.844 0.427,0.302 2.594,4.313 2.458,4.313 2.458,4.313 2.354,3.802 true 2.677,0.271 2.51,0.271 2.51,0.271 2.052,1.156 true 2.177,1.135 2.5,0.563 2.5,0.563 2.625,0.563 true 0.188,0.969 0.646,1.167 0.458,0.198 10 false G45 1.573,2.594 2.031,2.792 0.458,0.198 10 false G8 2.719,0.208 3.333,0.406 0.615,0.198 10 false CANH 2.729,0.479 3.344,0.677 0.615,0.198 10 false CANL 2.677,4.229 3.292,4.427 0.615,0.198 10 false BAT 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.156,2.469 0.469,2.625 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-13 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G45-14 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

11.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
a.
C317106C11
0.083,1.313 0.51,1.615 0.427,0.302 1.448,2.542 1.875,2.844 0.427,0.302 2.594,4.313 2.458,4.313 2.458,4.313 2.323,3.813 true 1.458,1.979 1.604,1.979 1.604,1.979 1.885,1.396 true 1.552,2.25 1.698,2.25 1.698,2.25 2.021,1.375 true 0.198,1.385 0.656,1.583 0.458,0.198 10 false G83 1.573,2.594 2.031,2.792 0.458,0.198 10 false G8 1.094,2.177 1.542,2.375 0.448,0.198 10 false CANH 1.052,1.906 1.448,2.094 0.396,0.188 10 false CANL 2.677,4.229 3.292,4.427 0.615,0.198 10 false BAT 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.156,2.469 0.469,2.625 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G83-24 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G83-23 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

13.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
a.
C317106C13
1.49,0.063 1.917,0.365 0.427,0.302 1.448,2.542 1.875,2.844 0.427,0.302 2.594,4.313 2.458,4.313 2.458,4.313 2.344,3.813 true 0.688,2.031 0.833,2.031 0.833,2.031 1.073,1.563 true 0.677,1 0.802,1 0.802,1 1.052,1.292 true 1.604,0.135 2.063,0.333 0.458,0.198 10 false G85 1.583,2.604 2.042,2.802 0.458,0.198 10 false G8 0.229,0.927 0.667,1.125 0.438,0.198 10 false CANH 0.25,1.948 0.677,2.135 0.427,0.188 10 false CANL 2.677,4.229 3.292,4.427 0.615,0.198 10 false BAT 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.156,2.469 0.469,2.625 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-17 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G85-28 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

15.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)
a.
C334426C01
1.406,0.083 1.948,0.406 0.542,0.323 1.458,1.948 2,2.271 0.542,0.323 2.281,1.281 2.594,1.083 2.594,1.083 2.708,1.083 true 2.281,1.5 2.583,1.906 2.583,1.906 2.698,1.906 true 2.198,2.938 2.448,3.24 2.448,3.24 2.563,3.24 true 0.063,0.031 0.375,0.188 0.313,0.156 10 false *a 0.073,2.042 0.385,2.198 0.313,0.156 10 false *b 2.771,1 3.385,1.198 0.615,0.198 10 false CANH 2.771,1.823 3.385,2.021 0.615,0.198 10 false CANL 1.51,0.156 2.125,0.354 0.615,0.198 10 false G121 1.635,2.021 2.25,2.219 0.615,0.198 10 false G8 2.646,3.146 3.26,3.344 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G121-25 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G121-31 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

17.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
a.
C317107C05
1.448,2.531 1.917,2.833 0.469,0.302 1.51,0.177 1.979,0.479 0.469,0.302 1.948,1.125 0.938,0.594 0.938,0.594 0.771,0.594 true 2.063,1.135 2.521,0.646 2.521,0.646 2.656,0.646 true 2.74,4.333 2.583,4.333 2.583,4.333 2.344,3.792 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 0.146,2.479 0.458,2.635 0.313,0.156 10 false *b 1.615,0.24 2.073,0.438 0.458,0.198 10 false G37 1.615,2.583 2.073,2.781 0.458,0.198 10 false G8 0.344,0.531 0.958,0.729 0.615,0.198 10 false CANH 2.729,0.552 3.344,0.75 0.615,0.198 10 false CANL 2.802,4.25 3.417,4.448 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of DLC3


Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-9 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G37-10 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

19.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
a.
C317107C07
1.448,2.531 1.917,2.833 0.469,0.302 1.51,0.177 1.979,0.479 0.469,0.302 1.948,1.125 0.938,0.594 0.938,0.594 0.771,0.594 true 2.063,1.135 2.521,0.646 2.521,0.646 2.656,0.646 true 2.74,4.333 2.583,4.333 2.583,4.333 2.344,3.792 true 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 0.146,2.479 0.458,2.635 0.313,0.156 10 false *b 1.573,0.24 2.031,0.438 0.458,0.198 10 false G113 1.615,2.583 2.073,2.781 0.458,0.198 10 false G8 0.344,0.531 0.958,0.729 0.615,0.198 10 false CANH 2.729,0.552 3.344,0.75 0.615,0.198 10 false CANL 2.802,4.25 3.417,4.448 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of DLC3


Disconnect the navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G113-9 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G113-10 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)

21.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (TELEMATICS TRANSCEIVER BRANCH WIRE)
22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (TELEMATICS TRANSCEIVER BRANCH WIRE)
a.
C300851C16
0.167,3.406 0.573,3.698 0.406,0.292 0.146,1.177 0.552,1.469 0.406,0.292 1.802,4.344 1.948,4.344 1.948,4.344 2.313,3.844 true 1.177,0.563 1.323,0.563 1.323,0.563 1.823,1.333 true 2.448,0.552 2.302,0.552 2.302,0.552 1.927,1.323 true 0.146,0.167 0.458,0.323 0.313,0.156 10 false *a 0.229,2.51 0.542,2.667 0.313,0.156 10 false *b 0.188,1.24 0.583,1.427 0.396,0.188 10 false G130 0.271,3.479 0.583,3.646 0.313,0.167 10 false G8 0.802,0.49 1.219,0.635 0.417,0.146 10 false CANP 2.5,0.49 2.917,0.635 0.417,0.146 10 false CANN 1.51,4.281 1.927,4.427 0.417,0.146 10 false BAT
*a Front view of wire harness connector
(to Telematics Transceiver)
*b Front view of DLC3


Disconnect the telematics transceiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G130-15 (CANP) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G130-16 (CANN) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO TELEMATICS TRANSCEIVER (CANP, CANN)

23.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.
C317114C05
1.448,2.521 1.927,2.781 0.479,0.26 1.521,0.125 2,0.385 0.479,0.26 1.74,1.083 2.49,0.531 2.49,0.531 2.635,0.531 true 1.646,1.073 0.885,0.552 0.885,0.552 0.719,0.552 true 2.688,4.344 2.531,4.344 2.531,4.344 2.344,3.802 true 0.104,0.063 0.417,0.219 0.313,0.156 10 false *a 0.104,2.438 0.417,2.594 0.313,0.156 10 false *b 1.646,0.177 2.104,0.375 0.458,0.198 10 false G33 1.604,2.563 2.063,2.76 0.458,0.198 10 false G8 2.719,0.438 3.177,0.635 0.458,0.198 10 false TX+ 0.438,0.458 0.896,0.656 0.458,0.198 10 false TX- 2.76,4.26 3.219,4.458 0.458,0.198 10 false BAT
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-11 (TX+) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G33-12 (TX-) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (TX+, TX-)

25.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.
C300856C11
1.542,2.781 1.958,3.052 0.417,0.271 1.396,0.208 1.813,0.479 0.417,0.271 1.865,1.927 1.979,1.927 1.979,1.927 2.521,1.063 true 2.667,1.063 2.719,1.948 2.719,1.948 2.833,1.948 true 1.781,4.427 1.906,4.427 1.906,4.427 2.344,3.958 true 0.146,0.104 0.458,0.26 0.313,0.156 10 false *a 0.198,2.635 0.51,2.792 0.313,0.156 10 false *b 1.656,2.844 1.938,3.01 0.281,0.167 10 false G8 1.479,0.26 1.844,0.417 0.365,0.156 10 false G77 1.583,1.844 2.01,2 0.427,0.156 10 false TX+ 2.896,1.875 3.323,2.031 0.427,0.156 10 false TX- 1.469,4.365 1.896,4.521 0.427,0.156 10 false BAT
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G77-8 (TX+) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G77-9 (TX-) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (TX+, TX-)

27.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

28.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
28.CHECK SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C348063C12
1.813,0.563 2.333,0.865 0.521,0.302 5.24,0.417 5.76,0.719 0.521,0.302 1.083,1.417 0.854,1.01 0.854,1.01 0.688,1.01 true 1.281,1.427 0.99,0.802 0.99,0.802 0.823,0.802 true 1.094,1.583 0.885,1.906 0.885,1.906 0.719,1.906 true 1.292,1.573 0.969,2.104 0.969,2.104 0.802,2.104 true 2.229,1.406 2.896,0.375 2.896,0.375 3.052,0.375 true 2.198,1.563 2.906,2.552 2.906,2.552 3.063,2.552 true 6.104,1.74 6.344,2.198 6.344,2.198 6.5,2.198 true 1.5,1.563 1.115,2.313 1.115,2.313 0.948,2.313 true 1.479,1.417 1.115,0.615 1.115,0.615 0.948,0.615 true 1.844,1.417 1.208,0.427 1.208,0.427 1.042,0.427 true 1.854,1.573 1.229,2.521 1.229,2.521 1.063,2.521 true 2.406,1.563 3,2.365 3,2.365 3.156,2.365 true 2.438,1.417 3,0.573 3,0.573 3.156,0.573 true 2.625,1.427 3.094,0.792 3.094,0.792 3.25,0.792 true 2.625,1.583 3.115,2.208 3.115,2.208 3.271,2.208 true 1.938,0.625 2.552,0.823 0.615,0.198 10 false G67 5.406,0.49 6.021,0.688 0.615,0.198 10 false G8 0.167,0.938 1.083,1.135 0.917,0.198 10 false CANH*c 0.25,0.729 1.167,0.927 0.917,0.198 10 false CANH*d 3.083,0.292 4,0.49 0.917,0.198 10 false CANH*g 0.396,0.542 1.313,0.74 0.917,0.198 10 false CANH*e 0.167,1.833 1.083,2.031 0.917,0.198 10 false CANL*c 0.26,2.031 1.177,2.229 0.917,0.198 10 false CANL*d 0.375,2.24 1.292,2.438 0.917,0.198 10 false CANL*e 3.125,2.479 4.042,2.677 0.917,0.198 10 false CANL*g 0.135,0.104 1.052,0.302 0.917,0.198 10 false *a 4.146,0.135 5.063,0.333 0.917,0.198 10 false *b 6.594,2.115 7,2.51 0.406,0.396 10 false BAT 0.5,0.333 1.417,0.531 0.917,0.198 10 false CANH*f 0.542,2.427 1.458,2.625 0.917,0.198 10 false CANL*f 3.24,2.281 4.156,2.479 0.917,0.198 10 false CANL*h 3.219,0.5 4.135,0.698 0.917,0.198 10 false CANH*h 3.313,0.708 4.229,0.906 0.917,0.198 10 false CANH*i 3.333,2.125 4.25,2.323 0.917,0.198 10 false CANL*i
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3
*c to Brake Actuator Assembly (Skid Control ECU) *d to Airbag Sensor Assembly (w/ Airbag System)
*e to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) (w/ VSC) *f to Combination Meter Assembly
*g to No. 2 CAN Junction Connector *h to Engine Stop and Start ECU (w/ Stop and Start System)
*i to Headlight Leveling ECU Assembly (for LED Headlight or w/ Headlight Cleaner System) - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ VSC

*2: for LED Headlight or w/ Headlight Cleaner System

*3: w/ Airbag System

*4: w/ Stop and Start System

G67-1 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Brake Actuator Assembly (Skid Control ECU)
G67-11 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G67-2 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Airbag Sensor Assembly*3
G67-12 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G67-3 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)*1
G67-13 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G67-5 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Combination Meter Assembly
G67-15 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G67-6 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher No. 2 CAN Junction Connector
G67-16 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G67-7 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Engine Stop and Start ECU*4
G67-17 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G67-8 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Headlight Leveling ECU Assembly*2
G67-18 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Result Proceed to
OK A
NG (to brake actuator assembly [skid Control ECU] CAN branch wire) B
NG (to airbag sensor assembly CAN branch wire) (w/ Airbag System) C
NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) (w/ VSC) D
NG (to combination meter assembly CAN main wire) E
NG (to engine stop and start ECU CAN branch wire) (w/ Stop and Start System) F
NG (to headlight leveling ECU assembly CAN branch wire) (for LED Headlight or w/ Headlight Cleaner System) G
NG (to No. 2 CAN junction connector CAN main wire) H



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

29.CONNECT CONNECTOR

C

31.CONNECT CONNECTOR

D

33.CONNECT CONNECTOR

E

35.CONNECT CONNECTOR

F

37.CONNECT CONNECTOR

G

39.CONNECT CONNECTOR

H

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

29.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)
30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)
a.

Disconnect the brake actuator assembly (skid control ECU) connector.

C317108C05
1.083,0.292 1.521,0.573 0.438,0.281 3.448,0.26 3.885,0.542 0.438,0.281 5.823,0.281 6.26,0.563 0.438,0.281 2.917,2.26 3.115,2.26 3.115,2.26 3.375,1.5 true 6.25,2.219 6.396,2.219 6.396,2.219 6.594,1.583 true 3.375,1.406 3.01,0.646 3.01,0.646 2.865,0.646 true 1.635,1.208 0.927,0.656 0.927,0.656 0.76,0.656 true 0.917,2.167 1.073,2.167 1.073,2.167 1.615,1.344 true 0.094,0.104 0.406,0.26 0.313,0.156 10 false *a 4.938,0.104 5.25,0.26 0.313,0.156 10 false *b 1.229,0.344 1.542,0.542 0.313,0.198 10 false A4 3.583,0.323 3.896,0.521 0.313,0.198 10 false A3 5.958,0.344 6.271,0.542 0.313,0.198 10 false G8 0.333,2.094 0.948,2.292 0.615,0.198 10 false CANH*A 0.198,0.583 0.813,0.781 0.615,0.198 10 false CANL*A 2.323,2.177 2.938,2.375 0.615,0.198 10 false CANH*B 2.292,0.563 2.906,0.76 0.615,0.198 10 false CANL*B 1.625,0.365 1.938,0.563 0.313,0.198 10 false *A 3.99,0.333 4.302,0.531 0.313,0.198 10 false *B 5.917,2.135 6.25,2.354 0.333,0.219 10 false BAT
*A w/ VSC *B w/o VSC
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
*b Front view of DLC3



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ VSC
Tester Connection Condition Specified Condition
A4-22 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A4-10 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

w/o VSC
Tester Connection Condition Specified Condition
A3-25 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A3-14 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

31.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
a.
C317109C09
1.479,2.573 1.958,2.865 0.479,0.292 1.531,0.125 2.01,0.417 0.479,0.292 2.083,1.094 2.469,0.615 2.469,0.615 2.625,0.615 true 2.188,1.344 2.5,1.906 2.5,1.906 2.646,1.906 true 2.656,4.333 2.51,4.333 2.51,4.333 2.344,3.802 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.156,2.542 0.469,2.698 0.313,0.156 10 false *b 1.656,0.177 2.115,0.375 0.458,0.198 10 false G42 1.646,2.625 2.104,2.823 0.458,0.198 10 false G8 2.688,0.531 3.302,0.729 0.615,0.198 10 false CANH 2.729,1.813 3.344,2.01 0.615,0.198 10 false CANL 2.729,4.26 3.344,4.458 0.615,0.198 10 false BAT
*a Rear view of wire harness connector
(to Airbag sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.

Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

Type C:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G42-13 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G42-22 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY (CANH, CANL)

33.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

34.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
34.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR BRANCH WIRE)
a.
C317110C03
1.49,2.521 1.958,2.792 0.469,0.271 1.542,0.167 2.01,0.438 0.469,0.271 1.813,1.344 1.958,1.906 1.958,1.906 2.094,1.906 true 1.635,1.354 1.469,1.854 1.469,1.854 1.323,1.854 true 2.344,3.781 2.49,4.281 2.49,4.281 2.625,4.281 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.146,2.458 0.458,2.615 0.313,0.156 10 false *b 1.646,0.219 2.104,0.417 0.458,0.198 10 false G21 1.635,2.573 2.094,2.771 0.458,0.198 10 false G8 2.167,1.813 2.781,2.01 0.615,0.198 10 false CANH 0.906,1.802 1.323,2.042 0.417,0.24 10 false CANL 2.708,4.208 3.323,4.406 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])
*b Front view of DLC3


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G21-3 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G21-2 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (CANH, CANL)

35.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

36.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
36.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
a.
C317111C03
1.479,2.583 1.938,2.875 0.458,0.292 1.458,0.052 1.917,0.344 0.458,0.292 1.385,1.073 1.219,1.948 1.219,1.948 1.083,1.948 true 2.656,4.26 2.521,4.26 2.521,4.26 2.344,3.792 true 1.313,1.073 1.073,1.615 1.073,1.615 0.938,1.615 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 0.146,2.521 0.458,2.677 0.313,0.156 10 false *b 1.604,0.125 1.917,0.323 0.313,0.198 10 false G9 1.635,2.635 1.948,2.833 0.313,0.198 10 false G8 0.51,1.542 1.125,1.74 0.615,0.198 10 false CANH 0.667,1.875 1.281,2.073 0.615,0.198 10 false CANL 2.74,4.167 3.354,4.365 0.615,0.198 10 false BAT
*a Rear view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-36 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G9-35 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

37.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ENGINE STOP AND START ECU BRANCH WIRE)
38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ENGINE STOP AND START ECU BRANCH WIRE)
a.
C317112C03
1.448,0.125 1.917,0.375 0.469,0.25 1.406,2.604 1.875,2.854 0.469,0.25 2.677,4.323 2.542,4.323 2.542,4.323 2.344,3.792 true 2.635,1.844 2.51,1.844 2.51,1.844 2.24,1.188 true 2.625,0.615 2.49,0.615 2.49,0.615 2.333,1.135 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.104,2.594 0.417,2.75 0.313,0.156 10 false *b 1.521,0.177 1.979,0.375 0.458,0.198 10 false G127 1.552,2.646 2.01,2.844 0.458,0.198 10 false G8 2.708,1.75 3.323,1.948 0.615,0.198 10 false CANL 2.708,0.531 3.323,0.729 0.615,0.198 10 false CANH 2.75,4.24 3.365,4.438 0.615,0.198 10 false BAT
*a Rear view of wire harness connector
(to Engine Stop and Start ECU)
*b Front view of DLC3


Disconnect the engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-13 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G127-14 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ENGINE STOP AND START ECU (CANH, CANL)

39.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

40.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (HEADLIGHT LEVELING ECU ASSEMBLY BRANCH WIRE)
40.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (HEADLIGHT LEVELING ECU ASSEMBLY BRANCH WIRE)
a.
C317113C03
1.417,2.51 1.906,2.781 0.49,0.271 1.49,0.125 1.979,0.396 0.49,0.271 2.24,0.938 1.146,0.417 1.146,0.417 0.969,0.417 true 2.646,4.365 2.521,4.365 2.521,4.365 2.333,3.781 true 2.417,0.948 2.563,0.385 2.563,0.385 2.688,0.385 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 0.146,2.49 0.458,2.646 0.313,0.156 10 false *b 1.594,0.177 2.052,0.375 0.458,0.198 10 false G80 1.583,2.573 2.042,2.771 0.458,0.198 10 false G8 0.542,0.344 1.156,0.542 0.615,0.198 10 false CANH 2.74,0.302 3.354,0.5 0.615,0.198 10 false CANL 2.74,4.271 3.354,4.469 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
*b Front view of DLC3


Disconnect the headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G80-6 (CANH) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G80-7 (CANL) - G8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT LEVELING ECU ASSEMBLY (CANH, CANL)