Home › Engine / Hybrid System › 2GD-FTV LUBRICATION › OIL PUMP › from 2016.08
RM3250E _51 Engine / Hybrid System _038011 2GD-FTV LUBRICATION _0187780 OIL PUMP A

2GD-FTV LUBRICATION  OIL PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

Make sure foreign matter does not enter the fuel path.

·

The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck or dropped.

·

Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control valve or fuel pipe, etc.



PROCEDURE

Hide 11310 1.INSTALL TIMING CHAIN CASE ASSEMBLY AND ENGINE WATER PUMP ASSEMBLY

a.

Apply a light coat of engine oil to the 4 new O-rings.


b.

Install the 4 O-rings to the cylinder block sub-assembly and cylinder head sub-assembly.


c.

Clean and degrease the contact surfaces of the timing chain case assembly, cylinder head sub-assembly and cylinder block sub-assembly.


d.

Apply a coating of seal packing to the timing chain case assembly at the points shown in the illustration.

A339594C01
4.375,6.74 4.708,6.74 true 1.135,7.313 1.469,7.313 true 2.927,7.313 3.26,7.313 true 6.635,6.74 6.865,6.74 true 1.396,0.729 1.625,0.948 0.229,0.219 10 false *a 5.802,0.76 6.031,0.948 0.229,0.188 10 false *b 2.531,5.625 2.771,5.844 0.24,0.219 10 false E 6.917,6.646 7.135,6.833 0.219,0.188 10 false *d 6.917,6.188 7.146,6.385 0.229,0.198 10 false *c 4.781,6.635 4.979,6.823 0.198,0.188 10 false *f 1.531,6.906 1.729,7.083 0.198,0.177 10 false *e 1.552,7.219 1.781,7.427 0.229,0.208 10 false *f 5.521,4.958 5.698,5.146 0.177,0.188 10 true C 4.49,0.792 4.698,0.969 0.208,0.177 10 true B 5.104,0.781 5.292,0.958 0.188,0.177 10 true B 2.333,0.865 2.531,1.042 0.198,0.177 10 true A 4.938,4.969 5.104,5.135 0.167,0.167 10 true C 3.448,1.531 3.625,1.708 0.177,0.177 10 true D 2.49,2.052 2.677,2.229 0.188,0.177 10 true E 3.26,2.063 3.448,2.24 0.188,0.177 10 true E 3.969,1.385 4.177,1.552 0.208,0.167 10 true E 4.896,1.229 5.083,1.396 0.188,0.167 10 true E 6.208,5.958 6.906,6.188 0.698,0.229 10 true A-A , B-B 2.823,0.75 3.021,0.927 0.198,0.177 10 true A 4.25,5.938 4.635,6.156 0.385,0.219 10 true C-C 0.708,5.615 0.896,5.823 0.188,0.208 10 false D 4.802,6.198 5.01,6.385 0.208,0.188 10 false *c 3.344,6.917 3.573,7.135 0.229,0.219 10 false *c 3.344,7.219 3.563,7.417 0.219,0.198 10 false *f 5.01,0.115 5.219,0.302 0.208,0.188 10 false *c 2.198,0.094 2.531,0.333 0.333,0.24 10 false *g 2.063,5.25 2.344,5.458 0.281,0.208 10 false *h 5.5,5.333 5.781,5.542 0.281,0.208 11 false *i
*a 46 mm (1.81 in.) *b 50 mm (1.97 in.)
*c 2.0 to 3.0 mm (0.0787 to 0.118 in.) *d 2.5 to 3.5 mm (0.0984 to 0.138 in.)
*e 3.0 to 4.0 mm (0.118 to 0.158 in.) *f 1.5 to 2.5 mm (0.0591 to 0.0984 in.)
*g 13 to 15 mm (0.512 to 0.591 in.) *h 9.0 to 11 mm (0.354 to 0.433 in.)
*i 31 to 33 mm (1.22 to 1.30 in.) - -


Seal packing:
for line area D:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent.

for line area A-A, B-B, C-C and E:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.


Seal Packing Application Specification:
Line Type and Area Seal Packing Diameter Application Area Seal Packing Application Length
Dashed Line 1.5 to 2.5 mm (0.0591 to 0.0984 in.) 2.0 to 3.0 mm (0.0787 to 0.118 in.) -
A - A 2.5 to 3.5 mm (0.0984 to 0.138 in.) 2.0 to 3.0 mm (0.0787 to 0.118 in.) 46 mm (1.81 in.)
B - B 2.5 to 3.5 mm (0.0984 to 0.138 in.) 2.0 to 3.0 mm (0.0787 to 0.118 in.) 50 mm (1.97 in.)
D 1.5 to 2.5 mm (0.0591 to 0.0984 in.) 3.0 to 4.0 mm (0.118 to 0.158 in.) -


NOTICE:
·

Using non-residue solvent, clean and remove any oil from the installation surface.

·

Install the part within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine within 2 hours after installation.




e.

Temporarily install the timing chain case assembly with the 15 bolts.

A339608C01
0.125,0.063 0.354,0.26 0.229,0.198 10 false *a 3.625,0.052 3.854,0.229 0.229,0.177 10 false *b 0.938,0.25 1.135,0.406 0.198,0.156 10 true A 1.031,0.542 1.219,0.698 0.188,0.156 10 true A 0.979,0.75 1.167,0.906 0.188,0.156 10 true D 0.875,0.99 1.063,1.146 0.188,0.156 10 true B 0.813,1.323 1,1.479 0.188,0.156 10 true B 0.646,1.729 0.833,1.885 0.188,0.156 10 true B 0.615,2.104 0.802,2.26 0.188,0.156 10 true B 0.646,2.51 0.833,2.667 0.188,0.156 10 true B 2.792,2.479 2.979,2.635 0.188,0.156 10 true B 2.885,2.073 3.073,2.229 0.188,0.156 10 true B 1.594,2.042 1.781,2.198 0.188,0.156 10 true B 1.792,1.927 1.948,2.083 0.156,0.156 10 true C 2.406,1.281 2.594,1.438 0.188,0.156 10 true C 2.177,2.042 2.365,2.198 0.188,0.156 10 true A 1.99,1.917 2.146,2.073 0.156,0.156 10 true C 1.771,1.177 1.958,1.333 0.188,0.156 10 true D 1.594,0.781 1.781,0.938 0.188,0.156 10 true C 2.573,1.031 2.76,1.188 0.188,0.156 10 true A 1.667,0.188 1.865,0.344 0.198,0.156 10 true A 1.969,0.188 2.167,0.344 0.198,0.156 10 true A 2.625,0.219 2.823,0.375 0.198,0.156 10 true A 2.656,0.479 2.854,0.635 0.198,0.156 10 true A 2.542,0.802 2.729,0.958 0.188,0.156 10 true D 5.948,1.271 6.104,1.427 0.156,0.156 10 true 1 4.26,1.75 4.417,1.896 0.156,0.146 10 true 2 4.406,1.302 4.552,1.448 0.146,0.146 10 true 3 4.469,0.99 4.625,1.135 0.156,0.146 10 true 4 5.135,0.792 5.281,0.948 0.146,0.156 10 true 5 5.531,1.917 5.677,2.073 0.146,0.156 10 true 6 5.354,1.917 5.51,2.073 0.156,0.156 10 true 7 5.167,2.042 5.313,2.198 0.146,0.156 10 true 8 4.25,2.51 4.406,2.656 0.156,0.146 10 true 9 4.156,2.104 4.354,2.26 0.198,0.156 10 true 10 5.688,2.052 5.885,2.219 0.198,0.167 10 true 11 6.427,2.094 6.635,2.26 0.208,0.167 10 true 12 6.323,2.479 6.531,2.646 0.208,0.167 10 true 13 6.125,1.052 6.323,1.208 0.198,0.156 10 true 14 6.083,0.833 6.271,0.99 0.188,0.156 10 true 15 5.323,1.177 5.521,1.333 0.198,0.156 10 true 16 4.531,0.75 4.719,0.896 0.188,0.146 10 true 17 4.51,0.271 4.708,0.417 0.198,0.146 10 true 18 4.594,0.563 4.792,0.708 0.198,0.146 10 true 19 5.208,0.198 5.406,0.344 0.198,0.146 10 true 20 5.521,0.198 5.708,0.344 0.188,0.146 10 true 21 6.208,0.49 6.406,0.635 0.198,0.146 10 true 22 6.208,0.208 6.406,0.365 0.198,0.156 10 true 23
*a Type of bolt *b Tightening


Bolt Length:
Item Length Thread Diameter
Bolt A 30 mm (1.18 in.) 8.0 mm (0.315 in.)
Bolt B 45 mm (1.77 in.) 8.0 mm (0.315 in.)
Bolt C 65 mm (2.56 in.) 8.0 mm (0.315 in.)
Bolt D 30 mm (1.18 in.) 10 mm (0.394 in.)



f.

Temporarily install a new gasket and the engine water pump assembly with the 8 bolts.


g.

Tighten the 23 bolts in the order shown in the illustration.

Torque:
for bolt A, B and C : 25 N*m (255 kgf*cm, 18 ft.*lbf)
for bolt D : 43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

Check the torque of bolt 1 after tightening bolt 23.



Hide 22815A 2.INSTALL INJECTION PUMP INSULATOR

Hide 22100 3.INSTALL SUPPLY PUMP ASSEMBLY

Hide 13559 4.INSTALL NO. 1 CHAIN TENSIONER SLIPPER

Hide 13561 5.TEMPORARILY INSTALL NO. 1 CHAIN VIBRATION DAMPER

Hide 13506 6.INSTALL CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

Hide 13561 7.TIGHTEN NO. 1 CHAIN VIBRATION DAMPER

Hide 13540 8.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13523 10.INSTALL CAMSHAFT TIMING SPROCKET

Hide 13562 11.INSTALL NO. 2 CHAIN VIBRATION DAMPER

Hide 13507 12.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

Hide 13559 13.INSTALL NO. 2 CHAIN TENSIONER SLIPPER

Hide 13550 14.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 13566B 15.INSTALL TIMING CHAIN GUIDE

Hide 16.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13519 17.INSTALL OIL PUMP DRIVE GEAR

a.

Install the oil pump drive gear to the crankshaft.


Hide 11324 18.INSTALL TIMING CHAIN COVER PLATE

Hide 11302 19.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new timing chain case gasket.


b.

Install the timing chain case gasket to the timing chain case assembly.


c.

Clean and degrease the contact surfaces of the timing chain cover sub-assembly and timing chain case assembly.


d.

Apply a coating of seal packing to the timing chain cover sub-assembly at the points shown in the illustration.

A339587C01
1.615,6.938 1.99,6.938 true 6.125,6.365 6.5,6.365 true 3.333,6.365 3.708,6.365 true 2.01,6.552 2.219,6.719 0.208,0.167 10 false *a 2.052,6.854 2.271,7.021 0.219,0.167 10 false *b 1.885,1.188 2.063,1.354 0.177,0.167 10 true A 2.375,1.167 2.552,1.333 0.177,0.167 10 true A 3.271,2.583 3.448,2.75 0.177,0.167 10 true B 2.792,2.5 2.969,2.667 0.177,0.167 10 true B 2.344,1.771 2.521,1.938 0.177,0.167 10 true C 3.479,0.51 3.656,0.677 0.177,0.167 10 true C 1.208,5.083 1.385,5.25 0.177,0.167 10 true C 3.167,5.365 3.479,5.542 0.313,0.177 10 true A-A 5.875,5.323 6.188,5.5 0.313,0.177 10 true B-B 3.719,5.844 3.927,6.01 0.208,0.167 10 false *a 3.76,6.271 3.979,6.438 0.219,0.167 10 false *b 6.406,5.833 6.615,6 0.208,0.167 10 false *a 6.542,6.271 6.76,6.438 0.219,0.167 10 false *b
*a 2.0 to 3.0 mm (0.0787 to 0.118 in.) *b 2.5 to 3.5 mm (0.0984 to 0.138 in.)


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.


Standard seal packing diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Using non-residue solvent, clean and remove any oil from the installation surface.

·

Install the part within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine within 2 hours after installation.




e.

Temporarily install the timing chain cover sub-assembly with the 20 bolts.

A339589C01
0.042,0.031 0.271,0.208 0.229,0.177 10 false *a 3.583,0.052 3.813,0.219 0.229,0.167 10 false *b 0.927,0.167 1.083,0.333 0.156,0.167 10 true A 0.969,0.594 1.115,0.75 0.146,0.156 10 true B 1.458,1.198 1.604,1.354 0.146,0.156 10 true B 1.781,1.26 1.938,1.417 0.156,0.156 10 true B 2.563,1.292 2.708,1.448 0.146,0.156 10 true B 1.667,1.479 1.823,1.635 0.156,0.156 10 true B 1.323,1.51 1.479,1.677 0.156,0.167 10 true A 1.135,0.99 1.281,1.146 0.146,0.156 10 true B 0.781,1.917 0.938,2.083 0.156,0.167 10 true A 0.75,2.24 0.906,2.406 0.156,0.167 10 true A 0.854,2.542 1.01,2.708 0.156,0.167 10 true A 2.677,2.542 2.833,2.708 0.156,0.167 10 true A 2.896,2.229 3.042,2.375 0.146,0.146 10 true B 3.083,1.865 3.24,2.031 0.156,0.167 10 true A 3.24,1.552 3.406,1.708 0.167,0.156 10 true B 3.167,1.156 3.333,1.313 0.167,0.156 10 true B 2.875,0.156 3.031,0.323 0.156,0.167 10 true A 3.094,0.74 3.26,0.906 0.167,0.167 10 true B 2.469,0.573 2.615,0.719 0.146,0.146 10 true B 2.146,0.115 2.323,0.281 0.177,0.167 11 true B 5.854,1.26 6.021,1.427 0.167,0.167 10 true 1 6.542,1.563 6.688,1.708 0.146,0.146 10 true 2 6.385,1.854 6.531,2 0.146,0.146 10 true 3 6.177,2.229 6.333,2.385 0.156,0.156 10 true 4 5.99,2.552 6.146,2.708 0.156,0.156 10 true 5 4.188,2.531 4.344,2.688 0.156,0.156 10 true 6 4.063,2.24 4.219,2.396 0.156,0.156 10 true 7 4.073,1.906 4.229,2.063 0.156,0.156 10 true 8 4.635,1.51 4.792,1.667 0.156,0.156 10 true 9 4.948,1.5 5.135,1.656 0.188,0.156 10 true 10 5.083,1.271 5.271,1.427 0.188,0.156 10 true 11 4.771,1.198 4.958,1.344 0.188,0.146 10 true 12 4.375,0.99 4.563,1.135 0.188,0.146 10 true 13 4.271,0.594 4.458,0.74 0.188,0.146 10 true 14 4.177,0.177 4.365,0.323 0.188,0.146 10 true 15 5.406,0.135 5.594,0.281 0.188,0.146 10 true 16 6.167,0.156 6.365,0.313 0.198,0.156 10 true 17 6,0.573 6.198,0.729 0.198,0.156 10 true 18 6.385,0.75 6.583,0.906 0.198,0.156 10 true 19 6.49,1.156 6.688,1.313 0.198,0.156 10 true 20
*a Type of bolt *b Tightening


Bolt Length:
Item Length Thread Diameter
Bolt A 40 mm (1.57 in.) 8.0 mm (0.315 in.)
Bolt B 25 mm (0.984 in.) 8.0 mm (0.315 in.)



f.

Tighten the 20 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Check the torque of bolt 1 after tightening bolt 20.



Hide 12101 21.INSTALL OIL PAN SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.


b.
A339599C01
0,0 0,0 false
V100143

Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes after applying seal packing.

·

Do not add engine oil within 2 hours of installation.

·

Do not start the engine for at least 2 hours after the installation.




c.
A339600C02
0.323,0.344 0.49,0.51 0.167,0.167 10 true A 0.948,0.052 1.115,0.219 0.167,0.167 10 true A 0.25,0.667 0.417,0.833 0.167,0.167 10 true A 0.188,1.104 0.354,1.271 0.167,0.167 10 true A 0.271,1.625 0.438,1.792 0.167,0.167 10 true A 0.688,1.938 0.854,2.104 0.167,0.167 10 true A 0.969,1.958 1.135,2.125 0.167,0.167 10 true A
V100135

Bolt
V100136

Nut


Install the oil pan sub-assembly to the cylinder block sub-assembly with the 23 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Check the torque of all nuts and bolts labeled A again.



Hide 89491 22.INSTALL ENGINE OIL LEVEL SENSOR

Hide 12144 23.INSTALL OIL PAN COVER SILENCER

a.

Install the oil pan cover silencer to the oil pan sub-assembly with the 5 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11201 24.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to the O-ring of the camshaft position sensor.


b.

Install a new cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil hole gaskets to the cylinder head cover sub-assembly.


c.

Clean and degrease the contact surfaces of the cylinder head cover sub-assembly and cylinder head sub-assembly.


d.

Apply seal packing as shown in the illustration.

A339583C01
2.5,1.406 2.969,1.406 true 0.51,2.344 0.51,1.698 true 1.354,2.333 1.354,1.073 true 6.052,1.156 6.521,1.156 true 4.375,0.375 5.333,0.375 true 0.469,3.698 0.698,3.104 0.698,3.104 0.844,3.104 true 1.354,4.979 1.354,4.271 true 2.938,4.979 2.813,4.979 2.813,4.979 2.406,4.563 true 0.427,2.396 0.646,2.563 0.219,0.167 10 false *1 1.281,2.385 1.49,2.542 0.208,0.156 10 true *2 3.052,1.323 3.26,1.5 0.208,0.177 10 false *3 6.604,1.073 6.823,1.24 0.219,0.167 10 false *4 0.792,0.302 1,0.469 0.208,0.167 10 true *a 2.51,1 2.719,1.188 0.208,0.188 10 true *b 0.302,1 0.51,1.167 0.208,0.167 10 true *c 5.917,0.156 6.104,0.323 0.188,0.167 10 true *d 1.875,0.313 2.083,0.479 0.208,0.167 10 true *a 6.719,0.521 6.927,0.688 0.208,0.167 10 true *a 6.719,1.667 6.927,1.833 0.208,0.167 10 true *a 5.927,2.01 6.115,2.177 0.188,0.167 10 true *d 4.135,0.292 4.344,0.448 0.208,0.156 10 true *3 0.896,3.479 1.104,3.646 0.208,0.167 10 true *a 1.885,3.49 2.094,3.656 0.208,0.167 10 true *a 2.375,4.135 2.583,4.323 0.208,0.188 10 true *b 0.406,4.156 0.615,4.323 0.208,0.167 10 true *c 0.917,3.021 1.135,3.188 0.219,0.167 10 false *1 1.271,5.01 1.479,5.167 0.208,0.156 10 true *2 3,4.906 3.208,5.083 0.208,0.177 10 false *3
*1 Timing Chain Cover Sub-assembly *2 Timing Chain Case Assembly
*3 Cylinder Head Sub-assembly *4 No. 3 Camshaft Bearing Cap
*a Seal Diameter: 3.0 to 6.0 mm (0.118 to 0.236 in.) *b Application Width: 7.0 mm (0.276 in.)
*c Application Width: 9.0 mm (0.354 in.) *d Application Width: 11.0 mm (0.433 in.)


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 6.0 mm (0.118 to 0.236 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine within 2 hours after installation.




e.
A339609C01
0,0 0.167,0.156 0.167,0.156 10 true 6 0.448,0.958 0.625,1.125 0.177,0.167 10 true 6 0.063,0.042 0.271,0.208 0.208,0.167 10 true 20 0.563,0.031 0.76,0.208 0.198,0.177 10 true 15 0.948,0.052 1.167,0.24 0.219,0.188 10 true 11 1.354,0.104 1.573,0.292 0.219,0.188 10 true 9 1.917,0.115 2.146,0.302 0.229,0.188 10 true 13 2.552,0.073 2.771,0.26 0.219,0.188 10 true 17 3.125,0.021 3.333,0.188 0.208,0.167 10 true 19 0.052,0.719 0.208,0.896 0.156,0.177 10 true 5 0.469,1.396 0.625,1.563 0.156,0.167 10 true 3 1.042,1.375 1.24,1.552 0.198,0.177 10 true 1 1.656,1.365 1.844,1.542 0.188,0.177 10 true 2 2.26,1.375 2.438,1.552 0.177,0.177 10 true 4 2.833,1.5 3.01,1.667 0.177,0.167 10 true 7 0.156,2.01 0.365,2.177 0.208,0.167 10 true 18 0.396,1.99 0.604,2.156 0.208,0.167 10 true 14 0.802,1.99 1,2.156 0.198,0.167 10 true 10 1.323,1.927 1.531,2.104 0.208,0.177 10 true 8 1.885,1.917 2.104,2.094 0.219,0.177 10 true 12 2.469,1.917 2.688,2.094 0.219,0.177 10 true 16 3.104,1.958 3.302,2.135 0.198,0.177 10 true 21 0,0 0.188,0.167 0.188,0.167 10 true *b 0,0 0.135,0.167 0.135,0.167 10 true 5 0,0 0.167,0.177 0.167,0.177 10 true 7 0,0 0.177,0.167 0.177,0.167 10 true 8 0,0 0.167,0.167 0.167,0.167 10 true 9 0,0 0.198,0.167 0.198,0.167 10 true 10 0,0 0.198,0.167 0.198,0.167 10 true 11 0,0 0.198,0.167 0.198,0.167 10 true 12 0,0 0.219,0.167 0.219,0.167 10 true 13 0,0 0.167,0.167 0.167,0.167 10 true 4 0,0 0.167,0.167 0.167,0.167 10 true 3 0,0 0.177,0.167 0.177,0.167 10 true 2 0,0 0.167,0.156 0.167,0.156 10 true 1 0,0 0.177,0.167 0.177,0.167 10 true 14 0,0 0.188,0.167 0.188,0.167 10 true 21 0,0 0.177,0.167 0.177,0.167 10 true 20 0,0 0.188,0.167 0.188,0.167 10 true 19 0,0 0.188,0.167 0.188,0.167 10 true 18 0,0 0.208,0.167 0.208,0.167 10 true 17 0,0 0.208,0.167 0.208,0.167 10 true 16 0,0 0.208,0.167 0.208,0.167 10 true 15
V100135

Bolt
V100136

Nut
V100137

Nozzle Holder Clamp Seat


Tighten the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and camshaft position sensor in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

When reusing the camshaft position sensor, check the O-rings.

·

Make sure that the O-ring is not cracked or jammed when installing it on the cylinder head cover sub-assembly.

·

Replace with a new part if it is dropped or if it receives a strong impact.

·

Check the torque of bolts 1 to 4 again.




Hide 23682 25.INSTALL NOZZLE HOLDER GASKET

Hide 23670 26.TEMPORARILY INSTALL INJECTOR ASSEMBLY

Hide 12501 27.INSTALL GENERATOR BRACKET SUB-ASSEMBLY

Hide 12281A 28.INSTALL NO. 1 ENGINE HANGER

Hide 16575C 29.INSTALL NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF)

Hide 88451B 32.INSTALL VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater)

Hide 16620 33.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

Install the V-ribbed belt tensioner assembly to the timing chain cover sub-assembly with 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16603 34.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.

Install the No. 1 idler pulley sub-assembly to the generator bracket sub-assembly with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16304 37.INSTALL WATER OUTLET SUB-ASSEMBLY

Hide 16207 38.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 15407 39.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY

Hide 17141 40.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 17141 43.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

Hide 87101 45.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)

Hide 16284 46.CONNECT NO. 1 AND NO. 2 TURBO WATER HOSE

Hide 16268 47.INSTALL NO. 1 WATER BY-PASS PIPE

Hide 16279 48.INSTALL NO. 3 WATER BY-PASS PIPE

Hide 12261 49.INSTALL PCV HOSE (except Cold Area Specification Vehicles)

Hide 89467B 54.INSTALL AIR FUEL RATIO SENSOR (w/ DPF)

Hide 23295D 55.INSTALL NO. 1 INJECTOR HOLDER (w/ DPF)

Hide 16281 56.CONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF)

Hide 16282 57.INSTALL NO. 5 WATER BY-PASS HOSE (w/ DPF)

Hide 12229 58.INSTALL PCV PIPE (for Cold Area Specification Vehicles)

Hide 16630D 59.INSTALL IDLER PULLEY ASSEMBLY (w/o Air Conditioning System)

Hide 88431 60.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 23701 62.TEMPORARILY INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 23670 63.TIGHTEN INJECTOR ASSEMBLY

Hide 23701 64.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

Hide 65.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 23760 66.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 68.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 23770 70.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 23804C 71.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

Hide 23815D 72.INSTALL NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

Hide 23804D 73.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ Pressurized Fuel Filter)

Hide 23271H 74.INSTALL NO. 1 FUEL HOSE

Hide 23273H 75.INSTALL NO. 2 FUEL HOSE

Hide 23243B 76.INSTALL FUEL PUMP MOTOR WIRE

Hide 22803 77.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY

Hide 79.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 11409 81.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 25624 82.INSTALL EGR VALVE ADAPTER WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/o EGR Cooler)

Hide 25800 83.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Cooler)

Hide 84.INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY (w/ DPF)

Hide 16209 85.INSTALL NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 25804 86.INSTALL VACUUM CONTROL VALVE SET (w/ EGR Cooler)

Hide 25601 87.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY (w/o DPF)

Hide 16206B 89.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/o EGR Cooler)

Hide 16206B 90.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 25625 92.INSTALL EGR VALVE BRACKET

Hide 12631A 95.INSTALL ENGINE COVER BRACKET

Hide 25734 97.TEMPORARILY INSTALL NO. 2 VACUUM PIPE (w/ DPF)

Hide 25733A 98.TEMPORARILY INSTALL NO. 1 VACUUM PIPE (w/ DPF)

Hide 89425 101.INSTALL EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)

Hide 89481B 102.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ DPF)

Hide 16278 103.INSTALL NO. 2 WATER BY-PASS PIPE

Hide 26100G 104.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 12631A 106.INSTALL ENGINE COVER BRACKET

Hide 82121 107.INSTALL ENGINE WIRE

Hide 12632 108.INSTALL NO. 2 ENGINE COVER BRACKET

Hide 44763C 109.INSTALL NO. 2 HOSE TO HOSE TUBE