12361
1.INSTALL FRONT ENGINE MOUNTING INSULATOR
Install the 2 front engine mounting insulators to the 2 front engine mounting brackets with the 2 nuts.
12391
2.INSTALL FRONT ENGINE MOUNTING INSULATOR RH
Install the front engine mounting insulator RH to the front engine mounting insulator sub-assembly with the bolt.
82121
3.INSTALL ENGINE WIRE
Install the engine wire to the engine assembly.
4.INSTALL ENGINE HANGER
5.REMOVE ENGINE ASSEMBLY TO ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.
Attach the engine sling device and hang the engine assembly with the chain block.
Remove the engine assembly from the engine stand.
6.INSTALL ENGINE ASSEMBLY
Slowly lower the engine assembly into the engine compartment.
Install the engine assembly to the body with the 4 bolts and 4 nuts.
Make sure to tighten the side with the nut.
When installing a bolt with a claw (stopper), make sure that the claw (stopper) does not damage the body of the vehicle.
Remove the 3 bolts, No. 1 engine hanger upper and No. 2 engine hanger.
11355
7.INSTALL REAR END PLATE
Install the rear end plate to the cylinder block with the bolt.
13405
8.INSTALL FLYWHEEL SUB-ASSEMBLY
Clean the bolt holes.
Using SST, hold the crankshaft pulley.
for Manual Transmission:
Install the flywheel sub-assembly to the crankshaft with the 8 bolts.
| *1 | Flywheel Sub-assembly |
| *2 | Pump Impeller Drive Plate |
| *3 | Rear Drive Plate Spacer |
| *a | Engine Side |
| *b | Transmission Side |
for Automatic Transmission:
Install the flywheel sub-assembly, the pump impeller drive plate and the rear drive plate spacer to the crankshaft with the 8 bolts.
Align either hole in the pump impeller drive plate and either hole in the rear drive plate spacer with the knock pin of the flywheel sub-assembly, and then install the flywheel sub-assembly, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.
Do not start the engine for at least 1 hour after installation.
As the rear drive plate spacer and pump impeller drive plate are not reversible, be sure to install them in the direction shown in the illustration.
for Automatic Transmission:
Install and uniformly tighten and tighten the 8 bolts in several steps in the sequence shown in the illustration.
w/o Viscous Heater:
Install the crankshaft pulley cover to the crankshaft pulley with the 4 bolts.
w/ Viscous Heater:
Install the crankshaft pulley cover and viscous heater crankshaft pulley to the crankshaft pulley with the 4 bolts.
31250
9.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)
for R151:
Click hereDrivetrain>CLUTCH>CLUTCH UNIT(for R151)>INSTALLATION
for RC60:
Click hereDrivetrain>CLUTCH>CLUTCH UNIT(for RC60, RC61)>INSTALLATION
31210
10.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)
for R151:
Click hereDrivetrain>CLUTCH>CLUTCH UNIT(for R151)>INSTALLATION
for RC60:
Click hereDrivetrain>CLUTCH>CLUTCH UNIT(for RC60, RC61)>INSTALLATION
31210
11.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)
for R151:
Click hereDrivetrain>CLUTCH>CLUTCH UNIT(for R151)>INSTALLATION
for RC60:
Click hereDrivetrain>CLUTCH>CLUTCH UNIT(for RC60, RC61)>INSTALLATION
35000
12.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
32101A
13.INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transmission)
33030
14.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
37100
15.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
37140
16.INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
17410
17.INSTALL FRONT EXHAUST PIPE ASSEMBLY
w/ Urea SCR System:
Click hereEngine / Hybrid System>2GD-FTV INTAKE / EXHAUST>EXHAUST PIPE(for Urea SCR System)>INSTALLATION
w/o Urea SCR System:
Click hereEngine / Hybrid System>2GD-FTV INTAKE / EXHAUST>EXHAUST PIPE>INSTALLATION
87120G
18.INSTALL VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)
Install the viscous heater with magnet clutch assembly to the No. 1 viscous heater bracket.
Connect the connector to the viscous heater with magnet clutch assembly.
19.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)
Install the water hose sub-assembly to the viscous heater with magnet clutch assembly, No. 2 water pipe and water outlet sub-assembly, and slide the 4 clamps to secure the 2 hoses.
Connect the water hose sub-assembly to the water inlet with the bolt.
88320
20.CONNECT COOLER COMPRESSOR ASSEMBLY
Temporarily install the cooler compressor assembly to the compressor mounting bracket with the 2 stud bolts.
Using an E8 "TORX" socket wrench, tighten the 2 stud bolts.
Install the 2 bolts and 2 nuts.
Connect the connector to the cooler compressor assembly.
Connect the suction hose sub-assembly to the water inlet and timing chain cover with the 2 bolts.
27020
21.INSTALL GENERATOR ASSEMBLY
44774
22.CONNECT UNION TO CONNECTOR TUBE HOSE
Connect the union to connector tube hose to the No. 1 hose to hose tube, and slide the clamp to secure the hose.
44320
23.CONNECT VANE PUMP ASSEMBLY
Connect the vane pump assembly to the generator bracket with the 2 bolts.
Connect the connector to the power steering oil pressure switch.
24.CONNECT WATER HOSE SUB-ASSEMBLY
Connect the water hose sub-assembly to the air conditioning unit assembly, slide the 2 clamps secure the 2 hoses.
74431
25.INSTALL BATTERY TRAY
28800
26.INSTALL BATTERY
74404B
27.INSTALL BATTERY CLAMP SUB-ASSEMBLY
Install the battery clamp sub-assembly to the battery with the 2 nuts.
28.CONNECT WIRE HARNESS
Connect the engine room main wire to the battery positive cable with the nut.
Attach the clamp and connect the No. 2 engine wire with the 2 bolts.
Connect the 2 connectors to the engine room relay block sub-assembly.
Connect the wire to wire to the engine room relay block sub-assembly with the nut.
Attach the 2 clips and install the No. 1 relay block cover side to the engine room relay block sub-assembly.
Attach the 3 clips and install the No. 1 relay block cover upper to the engine room relay block sub-assembly.
23273H
29.CONNECT NO. 2 FUEL HOSE
Connect the No. 2 fuel hose to the No. 3 nozzle leakage pipe assembly, and slide the clamp to secure the hose.
Attach the clamp to the No. 2 fuel hose.
23271H
30.CONNECT NO. 1 FUEL HOSE
Connect the No. 1 fuel hose to the No. 2 fuel pipe, and slide the clamp to secure the hose.
Attach the clamp to the No. 1 fuel hose.
77826A
31.INSTALL NO. 1 UREA TANK FILLER PIPE SUPPORT (w/ Urea SCR System)
77910
32.CONNECT UREA TANK FILLER PIPE ASSEMBLY (w/ Urea SCR System)
23300
33.CONNECT FUEL FILTER ASSEMBLY
17363K
34.INSTALL INTERCOOLER AIR TUBE
Install the intercooler air tube to the diesel throttle body assembly, and slide the clamp to secure the hose.
Connect the connector to the intake air temperature sensor.
17344E
35.INSTALL NO. 4 AIR TUBE
Install the No. 4 air hose to the No. 2 air tube and intercooler air tube, and slide the 2 clamps to secure the hose.
Connect the oil return hose to the engine oil level dipstick guide assembly, and slide the clamp to secure the hose.
17341F
36.INSTALL NO. 1 AIR HOSE
Install the No. 1 air hose to the compressor outlet elbow and No. 1 air tube, and slide the 2 clamps to secure the 2 hoses.
17801
37.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
38.INSTALL AIR CLEANER CAP AND HOSE
Attach the 4 clips and install the air cleaner cap and hose.
Tighten the hose clamp.
Attach the 2 clamp and connect the connector to the mass air flow meter.
82121
39.CONNECT ENGINE WIRE
Pass the engine wire into the cabin.
Attach the grommet to the body.
Make sure the direction of grommet is shown in the illustration.
Attach the clamp to connect the engine wire to the bracket.
Attach the clamp and connect the 4 connectors to the glow plug controller.
Connect the connector to the engine room main wire.
Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.
Install the ECM.
Click hereEngine / Hybrid System>2GD-FTV ENGINE CONTROL>ECM>INSTALLATION
16400
40.INSTALL RADIATOR ASSEMBLY
53301
41.INSTALL HOOD SUB-ASSEMBLY
Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.
Connect the washer nozzle hose to the hood sub-assembly.
42.ADD ENGINE OIL
43.ADD MANUAL TRANSMISSION OIL (for Manual Transmission)
44.ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
46.BLEED AIR FROM FUEL SYSTEM
47.ADD ENGINE COOLANT
48.INSPECT FOR COOLANT LEAK
49.INSPECT ENGINE OIL LEVEL
50.INSPECT ENGINE IDLE SPEED AND MAXIMUM SPEED
12601B
51.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
51442
52.INSTALL NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)
51410
53.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (for 4WD and Pre-Runner)