Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2015.06–2016.07
RM33J0E _58 Vehicle Interior _038504 HEATING / AIR CONDITIONING _0193639 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

The air conditioning amplifier assembly outputs the magnet clutch on request signal to the ECM. The ECM sends a magnet clutch on permission signal to the air conditioning amplifier assembly. The air conditioning amplifier assembly turns the magnet clutch on based on this signal.

WIRING DIAGRAM

E315708E07
5.208,3.385 5.667,3.583 0.458,0.198 10 false G33 5.219,3.552 6.792,4.01 1.573,0.458 10 false Air Conditioning Amplifier Assembly 5.417,1.604 5.875,1.802 0.458,0.198 10 false AC1 5.427,0.885 5.885,1.083 0.458,0.198 10 false ACT 5.427,2.542 5.885,2.74 0.458,0.198 10 false MGC 0.813,1.708 1.271,1.906 0.458,0.198 10 false AC1 0.813,0.979 1.271,1.177 0.458,0.198 10 false ACT 5.135,1.604 5.594,1.802 0.458,0.198 10 false 17 5.125,0.885 5.583,1.083 0.458,0.198 10 false 24 1.208,0.885 2.5,1.083 1.292,0.198 10 false 19*1,14*2, 24*3 1.219,1.604 2.688,1.802 1.469,0.198 10 false 18*1, 15*2, 30*3 5.156,2.542 5.615,2.74 0.458,0.198 10 false 20 4.51,2.542 4.969,2.74 0.458,0.198 10 false 1 3.313,2.542 3.771,2.74 0.458,0.198 10 false 2 3.302,2.948 3.76,3.146 0.458,0.198 10 false 5 4.521,2.948 4.979,3.146 0.458,0.198 10 false 3 3.635,3.385 5.083,3.635 1.448,0.25 10 false A/C COMP 4.802,3.99 5.26,4.188 0.458,0.198 10 false 1 3.188,4.49 4.823,4.74 1.635,0.25 10 false Magnet Clutch Assembly 2.813,4.979 4.448,5.229 1.635,0.25 10 false C3 2.813,5.125 5.479,5.375 2.667,0.25 10 false Compressor Assembly with Magnet Clutch 0.073,2.229 1.865,2.49 1.792,0.26 10 false G83*1, G86*2, G46*3 0.083,2.385 0.542,2.583 0.458,0.198 10 false ECM 0.26,2.646 2.083,2.875 1.823,0.229 10 false from IG1 NO.1 Relay 4.375,3.99 4.833,4.188 0.458,0.198 10 false MG+ 2.115,2.813 3,3.031 0.885,0.219 10 false IG1 NO.4 6,0.74 6.458,0.938 0.458,0.198 10 false +B 6.229,1.406 6.688,1.604 0.458,0.198 10 false IC 0.094,4.75 1.917,4.979 1.823,0.229 10 false *1: for 1KD-FTV 0.083,5.021 1.906,5.25 1.823,0.229 10 false *2: for 1GD-FTV 0.083,5.313 1.906,5.542 1.823,0.229 10 false *3: for 2TR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION



PROCEDURE

1.READ VALUE USING GTS (A/C SIGNAL)
a.

Use the Data List to check if the magnet clutch on request signal is functioning properly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/C Signal Magnet clutch on request signal ON or OFF ON: "A/C" switch on
OFF: "A/C" switch off
Operates with the engine idling and the blower switch on (LO level).
Powertrain > Engine and ECT > Data List
Tester Display
A/C Signal
50003 234 152
OK:

Display is as specified in normal condition.



Result:
Proceed to
OK
NG



OK

2.INSPECT MAGNET CLUTCH RELAY (A/C COMP)

NG

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
2.INSPECT MAGNET CLUTCH RELAY (A/C COMP)
a.

Remove the A/C COMP relay from the No. 4 instrument panel relay block assembly.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

REPLACE MAGNET CLUTCH RELAY (A/C COMP RELAY)

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
a.

Disconnect the air conditioning amplifier assembly connector.


b.
E269948C32
1.458,0.333 1.969,0.583 0.51,0.25 0.396,1.292 0.729,1.292 true 0.042,0.052 0.354,0.25 0.313,0.198 10 false *a 1.583,0.375 1.896,0.573 0.313,0.198 10 false G33 0.042,1.219 0.51,1.406 0.469,0.188 10 false MGC
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G33-20 (MGC) - Body ground Engine switch off Below 1 V
G33-20 (MGC) - Body ground Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


b.
E315707C04
1.229,0.344 1.729,0.594 0.5,0.25 0.375,0.594 0.625,0.594 0.625,0.594 0.677,1.135 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 1.333,0.385 1.792,0.583 0.458,0.198 10 false G33 0.042,0.51 0.5,0.708 0.458,0.198 10 false MGC
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G33-20 (MGC) - Body ground
·

Engine idling

·

Blower switch: On (LO level)

·

"A/C" switch: On (magnet clutch on)


Below 1 V
G33-20 (MGC) - Body ground
·

Engine idling

·

Blower switch on (LO level)

·

"A/C" switch off or on (magnet clutch off)


11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT MAGNET CLUTCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (A/C COMP RELAY - COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH AND BATTERY)
a.

Remove the A/C COMP relay from the No. 4 instrument panel junction block assembly.


b.

Disconnect the C3 compressor assembly with magnet clutch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 3 - C3-1 (MG+) Always Below 1 Ω
Relay terminal 3 or C3-1 (MG+) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Relay terminal 5 - Body ground Engine switch off Below 1 V
Relay terminal 5 - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
a.

Disconnect the G33 air conditioning amplifier assembly connector.


b.

Disconnect the G83*1, G86*2 or G46*3 ECM connector.

*1: for 1KD-FTV

*2: for 1GD-FTV

*3: for 2TR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV:
Tester Connection Condition Specified Condition
G33-17 (AC1) - G83-18 (AC1) Always Below 1 Ω
G33-24 (ACT) - G83-19 (ACT) Always Below 1 Ω
G33-17 (AC1) or G83-18 (AC1) - Body ground Always 10 kΩ or higher
G33-24 (ACT) or G83-19 (ACT) - Body ground Always 10 kΩ or higher

for 1GD-FTV:
Tester Connection Condition Specified Condition
G33-17 (AC1) - G86-15 (AC1) Always Below 1 Ω
G33-24 (ACT) - G86-14 (ACT) Always Below 1 Ω
G33-17 (AC1) or G86-15 (AC1) - Body ground Always 10 kΩ or higher
G33-24 (ACT) or G86-14 (ACT) - Body ground Always 10 kΩ or higher

for 2TR-FE:
Tester Connection Condition Specified Condition
G33-17 (AC1) - G46-30 (AC1) Always Below 1 Ω
G33-24 (ACT) - G46-24 (ACT) Always Below 1 Ω
G33-17 (AC1) or G46-30 (AC1) - Body ground Always 10 kΩ or higher
G33-24 (ACT) or G46-24 (ACT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


b.
E315707C05
1.229,0.344 1.729,0.594 0.5,0.25 0.531,0.594 0.781,0.594 0.781,0.594 0.917,1.135 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 1.344,0.385 1.802,0.583 0.458,0.198 10 false G33 0.24,0.51 0.698,0.708 0.458,0.198 10 false AC1
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G33-17 (AC1) - Body ground
·

Engine idling

·

Blower switch: On (LO level)

·

"A/C" switch: On


Below 1 V
G33-17 (AC1) - Body ground
·

Engine idling

·

Blower switch: On (LO level)

·

"A/C" switch: Off


11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECM)
a.

Disconnect the G33 air conditioning amplifier assembly connector.


b.

Disconnect the G83*1, G86*2 or G46*3 ECM connector.

*1: for 1KD-FTV

*2: for 1GD-FTV

*3: for 2TR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV:
Tester Connection Condition Specified Condition
G33-24 (ACT) - G83-19 (ACT) Always Below 1 Ω
G33-24 (ACT) or G83-19 (ACT) - Body ground Always 10 kΩ or higher

for 1GD-FTV:
Tester Connection Condition Specified Condition
G33-24 (ACT) - G86-14 (ACT) Always Below 1 Ω
G33-24 (ACT) or G86-14 (ACT) - Body ground Always 10 kΩ or higher

for 2TR-FE:
Tester Connection Condition Specified Condition
G33-24 (ACT) - G46-24 (ACT) Always Below 1 Ω
G33-24 (ACT) or G46-24 (ACT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK ECM
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


b.
E315707C06
1.229,0.344 1.729,0.594 0.5,0.25 2.479,1.823 2.177,1.823 2.177,1.823 2.01,1.292 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 1.344,0.385 1.802,0.583 0.458,0.198 10 false G33 2.531,1.729 2.99,1.927 0.458,0.198 10 false ACT
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G33-24 (ACT) - Body ground
·

Engine idling

·

Blower switch: On (LO level)

·

"A/C" switch: Off or on (magnet clutch off)


Below 1 V
G33-24 (ACT) - Body ground
·

Engine idling

·

Blower switch: On (LO level)

·

"A/C" switch: On (magnet clutch on)


4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG