Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › CYLINDER HEAD GASKET
RM33J0E _51 Engine / Hybrid System _038447 2KD-FTV ENGINE MECHANICAL _0201070 CYLINDER HEAD GASKET A

2KD-FTV ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

No. 3 injection pipe sub-assembly

·

No. 4 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing Gear Case Assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly, No. 3 injection pipe sub-assembly, No. 4 injection pipe sub-assembly and fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.
A352042C01
2.823,0.229 3.073,0.229 true 3.104,0.115 3.313,0.323 0.208,0.208 10 false *a 3.125,1.292 3.333,1.5 0.208,0.208 10 false *b
*a Measuring Tip
*b Protrusion


Check the piston protrusions for each cylinder.

i.

Clean the cylinder block sub-assembly with solvent.


ii.

Set the piston of the cylinder to be measured to slightly before TDC.


iii.

Place a dial indicator on the cylinder block sub-assembly, and position the measuring tip as shown in the illustration.


iv.

Set the dial indicator at 0 mm (0 in.)

HINT:

Make sure that the measuring tip is square to the cylinder block sub-assembly gasket surface and piston head when taking the measurements.




b.

Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.


c.
A352043C01
0.552,1.865 0.938,2.052 0.385,0.188 10 false X: *a
*a Measuring Point


Measure the piston protrusion of each cylinder at the 2 points shown in the illustration.


d.

For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.

Standard piston protrusion:

0.005 to 0.255 mm (0.000197 to 0.0100 in.)


HINT:

When installing the piston and connecting rod sub-assembly, if the protrusion is not as specified, remove the piston and connecting rod sub-assembly and reinstall them.



e.
A352044C01
2.719,1.021 2.969,1.188 0.25,0.167 10 false *a 1.667,0.552 1.917,0.719 0.25,0.167 10 false *a 0.479,0.156 0.635,0.323 0.156,0.167 10 false A 0.646,0.281 0.802,0.448 0.156,0.167 10 false B 0.792,0.396 0.948,0.563 0.156,0.167 10 false C 2.958,0.146 3.115,0.313 0.156,0.167 10 false D 3.104,0.25 3.26,0.417 0.156,0.167 10 false E
*a Cutout Mark
V100135

Front


Select a new cylinder head gasket.

HINT:

New cylinder head gaskets are available in 5 sizes, and are marked A, B, C, D or E.


New Cylinder Head Gasket Thickness:
Mark Specified Condition
A 0.80 to 0.90 mm (0.0315 to 0.0354 in.)
B 0.85 to 0.95 mm (0.0335 to 0.0374 in.)
C 0.90 to 1.00 mm (0.0354 to 0.0394 in.)
D 0.95 to 1.05 mm (0.0374 to 0.0413 in.)
E 1.00 to 1.10 mm (0.0394 to 0.0433 in.)


i.

Select the largest piston protrusion value from the measurements made. Then select a new appropriate cylinder head gasket according to the table below.

Gasket Size:
Item Specified Condition
Piston protrusion 0.005 to 0.054 mm (0.000197 to 0.00213 in.) 0.055 to 0.104 mm (0.00217 to 0.00409 in.) 0.105 to 0.154 mm (0.00413 to 0.00606 in.) 0.155 to 0.204 mm (0.00610 to 0.00803 in.) 0.205 to 0.255 mm (0.00807 to 0.0100 in.)
Gasket to be used A B C D E




f.

Place the cylinder head sub-assembly on the cylinder block sub-assembly.

NOTICE:
A352045C01
0,0 0,0 false
V100135

Front


Make sure the cylinder head gasket is installed facing the proper direction.



Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
·

The cylinder head set bolts are tightened in 3 progressive steps.

·

If any cylinder head set bolt is broken or deformed, replace it.



a.

Place the cylinder head sub-assembly on the cylinder head gasket.


b.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


c.
A352046C01
1.781,0.229 1.917,0.396 0.135,0.167 10 true 1 1.781,1.458 1.917,1.625 0.135,0.167 10 true 2 1.563,0.115 1.698,0.281 0.135,0.167 10 true 3 2,1.573 2.135,1.74 0.135,0.167 10 true 4 1.531,1.563 1.667,1.729 0.135,0.167 10 true 5 2.031,0.104 2.167,0.271 0.135,0.167 10 true 6 1.313,1.448 1.448,1.615 0.135,0.167 10 true 7 2.26,0.229 2.396,0.396 0.135,0.167 10 true 8 1.323,0.24 1.458,0.406 0.135,0.167 10 true 9 0.813,0.229 1.01,0.396 0.198,0.167 10 true 11 1.031,1.573 1.229,1.74 0.198,0.167 10 true 13 2.448,0.115 2.646,0.281 0.198,0.167 10 true 14 0.802,1.448 1,1.615 0.198,0.167 10 true 15 2.677,0.229 2.875,0.396 0.198,0.167 10 true 16 1.063,0.115 1.26,0.281 0.198,0.167 10 true 17 2.688,1.448 2.885,1.615 0.198,0.167 10 true 18 2.448,1.573 2.646,1.74 0.198,0.167 10 true 12 2.219,1.448 2.417,1.615 0.198,0.167 10 true 10
V100135

Bolt A
V100136

Bolt B


Install and uniformly tighten the 18 cylinder head set bolts and 18 washers in several passes in the sequence shown in the illustration.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

Standard Bolt Length
Item Specified Condition
Bolt A 110 mm (4.33 in.)
Bolt B 167 mm (6.57 in.)

If any of the cylinder head set bolts does not meet the torque specification, replace it.


d.
A060141C07
0.781,0.708 0.781,1.375 true 0.25,1.01 0.438,1.177 0.188,0.167 10 false *a 1.156,0.969 1.469,1.156 0.313,0.188 10 false 90° 1.802,0.531 2.115,0.719 0.313,0.188 10 false 90° 0.813,0.073 1.125,0.26 0.313,0.188 10 false 90° 0.052,0.479 0.365,0.667 0.313,0.188 10 false 90° 0.688,1.406 0.854,1.573 0.167,0.167 10 false *b
*a Front
*b Paint Mark


Mark the front of each cylinder head set bolt with paint.


e.

Further tighten the cylinder head set bolts by 90° in the sequence shown in the illustration above.


f.

Finally, tighten the cylinder head set bolts by an additional 90°.


g.

Check that the painted mark are now facing rearward.


Hide 11322B 5.INSTALL NO. 2 TIMING BELT COVER

a.
A352047C01
1.375,1.51 1.146,1.906 1.146,1.906 0.99,1.906 true 0.354,0.625 0.521,0.792 0.521,0.792 0.604,0.792 true 2.938,1.833 3.021,1.833 3.021,1.833 3.188,1.583 true 0.792,1.802 1.021,1.969 0.229,0.167 10 false *a 2.76,1.74 2.99,1.906 0.229,0.167 10 false *a 0.625,0.688 0.854,0.854 0.229,0.167 10 false *a
*a Seal Packing


Apply seal packing (FIPG) to the specified areas shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:

After applying FIPG, install the No. 2 timing belt cover within 3 minutes and tighten its bolts and nut within 15 minutes.



b.

Clean the bolts and their holes.


c.

Apply adhesive to 2 or 3 threads at the end of 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the No. 2 timing belt cover to the cylinder head sub-assembly and timing gear cover with the 4 bolts and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13523P 6.INSTALL CAMSHAFT TIMING PULLEY

a.
A352048

Install the camshaft timing pulley to the intake camshaft sub-assembly.


b.

Fasten the bolt of the camshaft timing pulley by holding the intake camshaft sub-assembly with a wrench.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)


Hide 13505 7.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

Hide 11322A 10.INSTALL NO. 1 TIMING BELT COVER

Hide 88431 11.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 88320 12.CONNECT COOLER COMPRESSOR ASSEMBLY

Hide 16711 13.INSTALL FAN SHROUD

Hide 23810A 15.INSTALL COMMON RAIL ASSEMBLY

Hide 23670 16.INSTALL INJECTOR ASSEMBLY

Hide 19850 17.INSTALL GLOW PLUG ASSEMBLY

Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION