Refer to DTC P16A0.
Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P16A0
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P16A1 | Delivery Heater Control Module Stuck ON | The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plugs are on (1 trip detection logic). | Glow plug controller | Does not come on | DTC stored |
| P16A3 | Cylinder 1 Delivery Heater Circuit/Open | An open circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic). | ·
Glow plug controller ·
No. 1 glow plug assembly ·
Open in No. 1 glow plug circuit ·
GLOW relay |
Does not come on | DTC stored |
| P16A4 | Cylinder 2 Delivery Heater Circuit/Open | An open circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic). | ·
Glow plug controller ·
No. 2 glow plug assembly ·
Open in No. 2 glow plug circuit ·
GLOW relay |
Does not come on | DTC stored |
| P16A5 | Cylinder 3 Delivery Heater Circuit/Open | An open circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic). | ·
Glow plug controller ·
No. 3 glow plug assembly ·
Open in No. 3 glow plug circuit ·
GLOW relay |
Does not come on | DTC stored |
| P16A6 | Cylinder 4 Delivery Heater Circuit/Open | An open circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic). | ·
Glow plug controller ·
No. 4 glow plug assembly ·
Open in No. 4 glow plug circuit ·
GLOW relay |
Does not come on | DTC stored |
| P16A7 | Cylinder 1 Delivery Heater Circuit High | A short circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic). | ·
Glow plug controller ·
No. 1 glow plug assembly ·
Short in No. 1 glow plug circuit |
Does not come on | DTC stored |
| P16A8 | Cylinder 2 Delivery Heater Circuit High | A short circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic). | ·
Glow plug controller ·
No. 2 glow plug assembly ·
Short in No. 2 glow plug circuit |
Does not come on | DTC stored |
| P16A9 | Cylinder 3 Delivery Heater Circuit High | A short circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic). | ·
Glow plug controller ·
No. 3 glow plug assembly ·
Short in No. 3 glow plug circuit |
Does not come on | DTC stored |
| P16AA | Cylinder 4 Delivery Heater Circuit High | A short circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (1 trip detection logic). | ·
Glow plug controller ·
No. 4 glow plug assembly ·
Short in No. 4 glow plug circuit |
Does not come on | DTC stored |
| P16AB | Disconnection between Delivery Heater and Delivery Heater Control Module | A short circuit in a wire harness between the glow plugs is detected 3 times while the glow plugs are on (1 trip detection logic). | ·
Glow plug controller ·
Short in glow plug circuit |
Does not come on | DTC stored |
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Turn the GTS on.
Using the GTS, switch the ECM from normal mode to check mode.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P16A1, P16A3 P16A4, P16A5, P16A6, P16A7, P16A8, P16A9, P16AA or P16AB.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P16A0.
Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P16A0
Inspect the fuses of circuits related to this system before performing the following procedure.
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P16A3, P16A4, P16A5 and/or P16A6 is output | A |
| P16A7, P16A8, P16A9 and/or P16AA is output | B |
| P16A1 and/or P16AB is output | C |
A
B
C
| *a | Front view of wire harness connector
(to Glow Plug Controller) |
Disconnect the glow plug controller connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Delivery Heater.
| Tester Display |
|---|
| Delivery Heater |
Operate the delivery heater using the Active Test function and measure the voltage according to the value(s) in the table below.
| Tester Connection | GTS Operation | Specified Condition |
|---|---|---|
| A56-1(BATT) - Body ground | Delivery heater is ON | 11 to 14 V |
Maximum operation time is 10 seconds.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connectors of the glow plug controller.
| *1 | Glow Plug Connector | - | - |
| *a | Front view of wire harness connector
(to Glow Plug Controller) |
*b | Front view of wire harness connector
(to Glow Plug Controller) |
Remove the glow plug connector from the glow plug assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C98-1 (GL1) - d1-1 | Always | Below 1 Ω |
| C98-2 (GL2) - d2-1 | Always | Below 1 Ω |
| C97-1 (GL3) - d3-1 | Always | Below 1 Ω |
| C97-2 (GL4) - d4-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect glow plug assembly.
Click hereEngine / Hybrid System>2TR-FBE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the GLOW relay.
Click hereEngine / Hybrid System>2TR-FBE FUEL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Remove the GLOW relay from the engine room relay block and junction block assembly.
Disconnect connectors of the glow plug controller.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GLOW relay terminal 5 - Battery positive terminal | Always | Below 1 Ω |
| GLOW relay terminal 1 - Body ground | Always | Below 1 Ω |
| GLOW relay terminal 3 - A56-1 (BATT) | Always | Below 1 Ω |
| GLOW relay terminal 2 - G46-7 (GREL) | Always | Below 1 Ω |
| GLOW relay terminal 5 or Battery positive terminal - Body ground | Always | 10 kΩ or higher |
| GLOW relay terminal 3 or A56-1 (BATT) - Body ground | Always | 10 kΩ or higher |
| GLOW relay terminal 2 or G46-7(GREL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connectors of the glow plug controller.
| *1 | Glow Plug Connector | - | - |
| *a | Front view of wire harness connector
(to Glow Plug Controller) |
*b | Front view of wire harness connector
(to Glow Plug Controller) |
Remove the glow plug connector from the glow plug assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C98-1 (GL1) or d1-1 - Other terminals | Always | 10 kΩ or higher |
| C98-2 (GL2) or d2-1 - Other terminals | Always | 10 kΩ or higher |
| C97-1 (GL3) or d3-1 - Other terminals | Always | 10 kΩ or higher |
| C97-2 (GL4) or d4-1 - Other terminals | Always | 10 kΩ or higher |
Make sure that there are no short circuits to the battery.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the glow plug controller.
Click hereEngine / Hybrid System>2TR-FBE FUEL>GLOW PLUG CONTROLLER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Turn the GTS on.
Using the GTS, switch the ECM from normal mode to check mode.
| Tester Display |
|---|
| Check Mode |
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
No DTC is output.
Check for DTCs in check mode.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect connectors of the glow plug controller.
| *1 | Glow Plug Connector | - | - |
| *a | Front view of wire harness connector
(to Glow Plug Controller) |
*b | Front view of wire harness connector
(to Glow Plug Controller) |
Remove the glow plug connector from the glow plug assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C98-1 (GL1) or d1-1 - Other terminals | Always | 10 kΩ or higher |
| C98-2 (GL2) or d2-1 - Other terminals | Always | 10 kΩ or higher |
| C97-1 (GL3) or d3-1 - Other terminals | Always | 10 kΩ or higher |
| C97-2 (GL4) or d4-1 - Other terminals | Always | 10 kΩ or higher |
Make sure that there are no short circuits to the battery.
| Proceed to |
|---|
| OK |
| NG |
OK
NG