When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. Upon receiving the signal, the ECM cancels the cruise control system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0571 | Brake Switch "A" Circuit | When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 seconds or more | ·
Stop light switch assembly ·
ECM ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Disconnect the stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-2 - Body ground | Always | 11 to 14 V |
| A35-4 - Body ground | Ignition switch ON | 11 to 14 V |
| A35-4 - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1KD-FTV
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G83-14 (ST1-) - Body ground | Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |
| G83-15 (STP) - Body ground | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | 0 to 1.5 V |
for 1GD-FTV
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G86-12 (ST1-) - Body ground | Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |
| G86-13 (STP) - Body ground | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | 0 to 1.5 V |
for 2TR-FBE
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G46-11 (ST1-) - Body ground | Ignition switch ON, brake pedal depressed | Below 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |
| G46-10 (STP) - Body ground | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2TR-FBE: Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>ECM>REMOVAL
NG